/* Target-struct-independent code to start (run) and stop an inferior
process.
- Copyright (C) 1986-2012 Free Software Foundation, Inc.
+ Copyright (C) 1986-2013 Free Software Foundation, Inc.
This file is part of GDB.
#include "mi/mi-common.h"
#include "event-top.h"
#include "record.h"
+#include "record-full.h"
#include "inline-frame.h"
#include "jit.h"
#include "tracepoint.h"
#include "skip.h"
#include "probe.h"
#include "objfiles.h"
+#include "completer.h"
+#include "target-descriptions.h"
/* Prototypes for local functions */
fprintf_filtered (file, _("Displace stepping debugging is %s.\n"), value);
}
-int debug_infrun = 0;
+unsigned int debug_infrun = 0;
static void
show_debug_infrun (struct ui_file *file, int from_tty,
struct cmd_list_element *c, const char *value)
"this platform."));
}
+/* User interface for non-stop mode. */
-/* If the program uses ELF-style shared libraries, then calls to
- functions in shared libraries go through stubs, which live in a
- table called the PLT (Procedure Linkage Table). The first time the
- function is called, the stub sends control to the dynamic linker,
- which looks up the function's real address, patches the stub so
- that future calls will go directly to the function, and then passes
- control to the function.
-
- If we are stepping at the source level, we don't want to see any of
- this --- we just want to skip over the stub and the dynamic linker.
- The simple approach is to single-step until control leaves the
- dynamic linker.
-
- However, on some systems (e.g., Red Hat's 5.2 distribution) the
- dynamic linker calls functions in the shared C library, so you
- can't tell from the PC alone whether the dynamic linker is still
- running. In this case, we use a step-resume breakpoint to get us
- past the dynamic linker, as if we were using "next" to step over a
- function call.
-
- in_solib_dynsym_resolve_code() says whether we're in the dynamic
- linker code or not. Normally, this means we single-step. However,
- if SKIP_SOLIB_RESOLVER then returns non-zero, then its value is an
- address where we can place a step-resume breakpoint to get past the
- linker's symbol resolution function.
-
- in_solib_dynsym_resolve_code() can generally be implemented in a
- pretty portable way, by comparing the PC against the address ranges
- of the dynamic linker's sections.
-
- SKIP_SOLIB_RESOLVER is generally going to be system-specific, since
- it depends on internal details of the dynamic linker. It's usually
- not too hard to figure out where to put a breakpoint, but it
- certainly isn't portable. SKIP_SOLIB_RESOLVER should do plenty of
- sanity checking. If it can't figure things out, returning zero and
- getting the (possibly confusing) stepping behavior is better than
- signalling an error, which will obscure the change in the
- inferior's state. */
-
-/* This function returns TRUE if pc is the address of an instruction
- that lies within the dynamic linker (such as the event hook, or the
- dld itself).
-
- This function must be used only when a dynamic linker event has
- been caught, and the inferior is being stepped out of the hook, or
- undefined results are guaranteed. */
-
-#ifndef SOLIB_IN_DYNAMIC_LINKER
-#define SOLIB_IN_DYNAMIC_LINKER(pid,pc) 0
-#endif
+int non_stop = 0;
+static int non_stop_1 = 0;
+
+static void
+set_non_stop (char *args, int from_tty,
+ struct cmd_list_element *c)
+{
+ if (target_has_execution)
+ {
+ non_stop_1 = non_stop;
+ error (_("Cannot change this setting while the inferior is running."));
+ }
+
+ non_stop = non_stop_1;
+}
+
+static void
+show_non_stop (struct ui_file *file, int from_tty,
+ struct cmd_list_element *c, const char *value)
+{
+ fprintf_filtered (file,
+ _("Controlling the inferior in non-stop mode is %s.\n"),
+ value);
+}
/* "Observer mode" is somewhat like a more extreme version of
non-stop, in which all GDB operations that might affect the
target's execution have been disabled. */
-static int non_stop_1 = 0;
-
int observer_mode = 0;
static int observer_mode_1 = 0;
set_observer_mode (char *args, int from_tty,
struct cmd_list_element *c)
{
- extern int pagination_enabled;
-
if (target_has_execution)
{
observer_mode_1 = observer_mode;
static unsigned char *signal_print;
static unsigned char *signal_program;
+/* Table of signals that are registered with "catch signal". A
+ non-zero entry indicates that the signal is caught by some "catch
+ signal" command. This has size GDB_SIGNAL_LAST, to accommodate all
+ signals. */
+static unsigned char *signal_catch;
+
/* Table of signals that the target may silently handle.
This is automatically determined from the flags above,
and simply cached here. */
/* Nonzero if we want to give control to the user when we're notified
of shared library events by the dynamic linker. */
int stop_on_solib_events;
+
+/* Enable or disable optional shared library event breakpoints
+ as appropriate when the above flag is changed. */
+
+static void
+set_stop_on_solib_events (char *args, int from_tty, struct cmd_list_element *c)
+{
+ update_solib_breakpoints ();
+}
+
static void
show_stop_on_solib_events (struct ui_file *file, int from_tty,
struct cmd_list_element *c, const char *value)
void init_thread_stepping_state (struct thread_info *tss);
-void init_infwait_state (void);
+static void init_infwait_state (void);
static const char follow_fork_mode_child[] = "child";
static const char follow_fork_mode_parent[] = "parent";
/* follow-fork child, detach-on-fork on. */
- old_chain = make_cleanup_restore_current_thread ();
+ inf->vfork_parent->pending_detach = 0;
+
+ if (!exec)
+ {
+ /* If we're handling a child exit, then inferior_ptid
+ points at the inferior's pid, not to a thread. */
+ old_chain = save_inferior_ptid ();
+ save_current_program_space ();
+ save_current_inferior ();
+ }
+ else
+ old_chain = save_current_space_and_thread ();
/* We're letting loose of the parent. */
tp = any_live_thread_of_process (inf->vfork_parent->pid);
}
}
-/* Enum strings for "set|show displaced-stepping". */
+/* Enum strings for "set|show follow-exec-mode". */
static const char follow_exec_mode_new[] = "new";
static const char follow_exec_mode_same[] = "same";
set_current_inferior (inf);
set_current_program_space (pspace);
}
+ else
+ {
+ /* The old description may no longer be fit for the new image.
+ E.g, a 64-bit process exec'ed a 32-bit process. Clear the
+ old description; we'll read a new one below. No need to do
+ this on "follow-exec-mode new", as the old inferior stays
+ around (its description is later cleared/refetched on
+ restart). */
+ target_clear_description ();
+ }
gdb_assert (current_program_space == inf->pspace);
if ((inf->symfile_flags & SYMFILE_NO_READ) == 0)
set_initial_language ();
-#ifdef SOLIB_CREATE_INFERIOR_HOOK
- SOLIB_CREATE_INFERIOR_HOOK (PIDGET (inferior_ptid));
-#else
+ /* If the target can specify a description, read it. Must do this
+ after flipping to the new executable (because the target supplied
+ description must be compatible with the executable's
+ architecture, and the old executable may e.g., be 32-bit, while
+ the new one 64-bit), and before anything involving memory or
+ registers. */
+ target_find_description ();
+
solib_create_inferior_hook (0);
-#endif
jit_inferior_created_hook ();
remove_displaced_stepping_state (inf->pid);
}
-/* Enum strings for "set|show displaced-stepping". */
-
-static const char can_use_displaced_stepping_auto[] = "auto";
-static const char can_use_displaced_stepping_on[] = "on";
-static const char can_use_displaced_stepping_off[] = "off";
-static const char *const can_use_displaced_stepping_enum[] =
-{
- can_use_displaced_stepping_auto,
- can_use_displaced_stepping_on,
- can_use_displaced_stepping_off,
- NULL,
-};
-
/* If ON, and the architecture supports it, GDB will use displaced
stepping to step over breakpoints. If OFF, or if the architecture
doesn't support it, GDB will instead use the traditional
which of all-stop or non-stop mode is active --- displaced stepping
in non-stop mode; hold-and-step in all-stop mode. */
-static const char *can_use_displaced_stepping =
- can_use_displaced_stepping_auto;
+static enum auto_boolean can_use_displaced_stepping = AUTO_BOOLEAN_AUTO;
static void
show_can_use_displaced_stepping (struct ui_file *file, int from_tty,
struct cmd_list_element *c,
const char *value)
{
- if (can_use_displaced_stepping == can_use_displaced_stepping_auto)
+ if (can_use_displaced_stepping == AUTO_BOOLEAN_AUTO)
fprintf_filtered (file,
_("Debugger's willingness to use displaced stepping "
"to step over breakpoints is %s (currently %s).\n"),
static int
use_displaced_stepping (struct gdbarch *gdbarch)
{
- return (((can_use_displaced_stepping == can_use_displaced_stepping_auto
- && non_stop)
- || can_use_displaced_stepping == can_use_displaced_stepping_on)
+ return (((can_use_displaced_stepping == AUTO_BOOLEAN_AUTO && non_stop)
+ || can_use_displaced_stepping == AUTO_BOOLEAN_TRUE)
&& gdbarch_displaced_step_copy_insn_p (gdbarch)
&& !RECORD_IS_USED);
}
displaced_step_prepare (ptid_t ptid)
{
struct cleanup *old_cleanups, *ignore_cleanups;
+ struct thread_info *tp = find_thread_ptid (ptid);
struct regcache *regcache = get_thread_regcache (ptid);
struct gdbarch *gdbarch = get_regcache_arch (regcache);
CORE_ADDR original, copy;
support displaced stepping. */
gdb_assert (gdbarch_displaced_step_copy_insn_p (gdbarch));
+ /* Disable range stepping while executing in the scratch pad. We
+ want a single-step even if executing the displaced instruction in
+ the scratch buffer lands within the stepping range (e.g., a
+ jump/branch). */
+ tp->control.may_range_step = 0;
+
/* We have to displaced step one thread at a time, as we only have
access to a single scratch space per inferior. */
a command like `return' or `jump' to continue execution."));
}
+ /* If we have a breakpoint to step over, make sure to do a single
+ step only. Same if we have software watchpoints. */
+ if (tp->control.trap_expected || bpstat_should_step ())
+ tp->control.may_range_step = 0;
+
/* If enabled, step over breakpoints by executing a copy of the
instruction at a different address.
displaced_step_dump_bytes (gdb_stdlog, buf, sizeof (buf));
}
+ if (tp->control.may_range_step)
+ {
+ /* If we're resuming a thread with the PC out of the step
+ range, then we're doing some nested/finer run control
+ operation, like stepping the thread out of the dynamic
+ linker or the displaced stepping scratch pad. We
+ shouldn't have allowed a range step then. */
+ gdb_assert (pc_in_thread_step_range (pc, tp));
+ }
+
/* Install inferior's terminal modes. */
target_terminal_inferior ();
tp->control.trap_expected = 0;
tp->control.step_range_start = 0;
tp->control.step_range_end = 0;
+ tp->control.may_range_step = 0;
tp->control.step_frame_id = null_frame_id;
tp->control.step_stack_frame_id = null_frame_id;
tp->control.step_over_calls = STEP_OVER_UNDEBUGGABLE;
struct thread_info *tp;
CORE_ADDR pc;
struct address_space *aspace;
- int oneproc = 0;
+ /* GDB may force the inferior to step due to various reasons. */
+ int force_step = 0;
/* If we're stopped at a fork/vfork, follow the branch set by the
"set follow-fork-mode" command; otherwise, we'll just proceed
actually be executing the breakpoint insn anyway.
We'll be (un-)executing the previous instruction. */
- oneproc = 1;
+ force_step = 1;
else if (gdbarch_single_step_through_delay_p (gdbarch)
&& gdbarch_single_step_through_delay (gdbarch,
get_current_frame ()))
/* We stepped onto an instruction that needs to be stepped
again before re-inserting the breakpoint, do so. */
- oneproc = 1;
+ force_step = 1;
}
else
{
is required it returns TRUE and sets the current thread to
the old thread. */
if (prepare_to_proceed (step))
- oneproc = 1;
+ force_step = 1;
}
/* prepare_to_proceed may change the current thread. */
tp = inferior_thread ();
- if (oneproc)
+ if (force_step)
{
tp->control.trap_expected = 1;
/* If displaced stepping is enabled, we can step over the
init_infwait_state ();
/* Resume inferior. */
- resume (oneproc || step || bpstat_should_step (), tp->suspend.stop_signal);
+ resume (force_step || step || bpstat_should_step (),
+ tp->suspend.stop_signal);
/* Wait for it to stop (if not standalone)
and in any case decode why it stopped, and act accordingly. */
ptid_t waiton_ptid;
/* Current inferior wait state. */
-enum infwait_states infwait_state;
+static enum infwait_states infwait_state;
/* Data to be passed around while handling an event. This data is
discarded between events. */
old_chain = make_cleanup_restore_current_thread ();
- switch_to_thread (info->ptid);
-
/* Go through handle_inferior_event/normal_stop, so we always
have consistent output as if the stop event had been
reported. */
old_chain_2 = make_cleanup (finish_thread_state_cleanup,
&minus_one_ptid);
- /* In non-stop mode, each thread is handled individually.
- Switch early, so the global state is set correctly for this
- thread. */
- if (non_stop
- && ecs->ws.kind != TARGET_WAITKIND_EXITED
- && ecs->ws.kind != TARGET_WAITKIND_SIGNALLED)
- context_switch (ecs->ptid);
-
/* Now figure out what to do with the result of the result. */
handle_inferior_event (ecs);
if (debug_infrun)
print_target_wait_results (waiton_ptid, ecs->ptid, &ecs->ws);
- if (non_stop
- && ecs->ws.kind != TARGET_WAITKIND_IGNORE
- && ecs->ws.kind != TARGET_WAITKIND_NO_RESUMED
- && ecs->ws.kind != TARGET_WAITKIND_EXITED
- && ecs->ws.kind != TARGET_WAITKIND_SIGNALLED)
- /* In non-stop mode, each thread is handled individually. Switch
- early, so the global state is set correctly for this
- thread. */
- context_switch (ecs->ptid);
-
/* If an error happens while handling the event, propagate GDB's
knowledge of the executing state to the frontend/user running
state. */
if (software_breakpoint_inserted_here_p (aspace, breakpoint_pc)
|| (non_stop && moribund_breakpoint_here_p (aspace, breakpoint_pc)))
{
- struct cleanup *old_cleanups = NULL;
+ struct cleanup *old_cleanups = make_cleanup (null_cleanup, NULL);
if (RECORD_IS_USED)
- old_cleanups = record_gdb_operation_disable_set ();
+ record_full_gdb_operation_disable_set ();
/* When using hardware single-step, a SIGTRAP is reported for both
a completed single-step and a software breakpoint. Need to
|| ecs->event_thread->prev_pc == breakpoint_pc)
regcache_write_pc (regcache, breakpoint_pc);
- if (RECORD_IS_USED)
- do_cleanups (old_cleanups);
+ do_cleanups (old_cleanups);
}
}
-void
+static void
init_infwait_state (void)
{
waiton_ptid = pid_to_ptid (-1);
infwait_state = infwait_normal_state;
}
-void
-error_is_running (void)
-{
- error (_("Cannot execute this command while "
- "the selected thread is running."));
-}
-
-void
-ensure_not_running (void)
-{
- if (is_running (inferior_ptid))
- error_is_running ();
-}
-
static int
stepped_in_from (struct frame_info *frame, struct frame_id step_frame_id)
{
handle_syscall_event (struct execution_control_state *ecs)
{
struct regcache *regcache;
- struct gdbarch *gdbarch;
int syscall_number;
if (!ptid_equal (ecs->ptid, inferior_ptid))
context_switch (ecs->ptid);
regcache = get_thread_regcache (ecs->ptid);
- gdbarch = get_regcache_arch (regcache);
syscall_number = ecs->ws.value.syscall_number;
stop_pc = regcache_read_pc (regcache);
if (catch_syscall_enabled () > 0
&& catching_syscall_number (syscall_number) > 0)
{
+ enum bpstat_signal_value sval;
+
if (debug_infrun)
fprintf_unfiltered (gdb_stdlog, "infrun: syscall number = '%d'\n",
syscall_number);
ecs->event_thread->control.stop_bpstat
= bpstat_stop_status (get_regcache_aspace (regcache),
stop_pc, ecs->ptid, &ecs->ws);
- ecs->random_signal
- = !bpstat_explains_signal (ecs->event_thread->control.stop_bpstat);
+
+ sval = bpstat_explains_signal (ecs->event_thread->control.stop_bpstat,
+ GDB_SIGNAL_TRAP);
+ ecs->random_signal = sval == BPSTAT_SIGNAL_NO;
if (!ecs->random_signal)
{
}
if (ecs->ws.kind != TARGET_WAITKIND_EXITED
- && ecs->ws.kind != TARGET_WAITKIND_SIGNALLED
- && !ptid_equal (ecs->ptid, minus_one_ptid))
+ && ecs->ws.kind != TARGET_WAITKIND_SIGNALLED)
{
ecs->event_thread = find_thread_ptid (ecs->ptid);
/* If it's a new thread, add it to the thread database. */
if (ecs->event_thread == NULL)
ecs->event_thread = add_thread (ecs->ptid);
+
+ /* Disable range stepping. If the next step request could use a
+ range, this will be end up re-enabled then. */
+ ecs->event_thread->control.may_range_step = 0;
}
/* Dependent on valid ECS->EVENT_THREAD. */
if (stop_soon == NO_STOP_QUIETLY)
{
struct regcache *regcache;
+ enum bpstat_signal_value sval;
if (!ptid_equal (ecs->ptid, inferior_ptid))
context_switch (ecs->ptid);
ecs->event_thread->control.stop_bpstat
= bpstat_stop_status (get_regcache_aspace (regcache),
stop_pc, ecs->ptid, &ecs->ws);
- ecs->random_signal
- = !bpstat_explains_signal (ecs->event_thread->control.stop_bpstat);
+
+ sval
+ = bpstat_explains_signal (ecs->event_thread->control.stop_bpstat,
+ GDB_SIGNAL_TRAP);
+ ecs->random_signal = sval == BPSTAT_SIGNAL_NO;
if (!ecs->random_signal)
{
we're attaching or setting up a remote connection. */
if (stop_soon == STOP_QUIETLY || stop_soon == NO_STOP_QUIETLY)
{
+ if (!ptid_equal (ecs->ptid, inferior_ptid))
+ context_switch (ecs->ptid);
+
/* Loading of shared libraries might have changed breakpoint
addresses. Make sure new breakpoints are inserted. */
if (stop_soon == NO_STOP_QUIETLY
case TARGET_WAITKIND_SPURIOUS:
if (debug_infrun)
fprintf_unfiltered (gdb_stdlog, "infrun: TARGET_WAITKIND_SPURIOUS\n");
+ if (!ptid_equal (ecs->ptid, inferior_ptid))
+ context_switch (ecs->ptid);
resume (0, GDB_SIGNAL_0);
prepare_to_wait (ecs);
return;
case TARGET_WAITKIND_EXITED:
+ case TARGET_WAITKIND_SIGNALLED:
if (debug_infrun)
- fprintf_unfiltered (gdb_stdlog, "infrun: TARGET_WAITKIND_EXITED\n");
+ {
+ if (ecs->ws.kind == TARGET_WAITKIND_EXITED)
+ fprintf_unfiltered (gdb_stdlog,
+ "infrun: TARGET_WAITKIND_EXITED\n");
+ else
+ fprintf_unfiltered (gdb_stdlog,
+ "infrun: TARGET_WAITKIND_SIGNALLED\n");
+ }
+
inferior_ptid = ecs->ptid;
set_current_inferior (find_inferior_pid (ptid_get_pid (ecs->ptid)));
set_current_program_space (current_inferior ()->pspace);
handle_vfork_child_exec_or_exit (0);
target_terminal_ours (); /* Must do this before mourn anyway. */
- print_exited_reason (ecs->ws.value.integer);
- /* Record the exit code in the convenience variable $_exitcode, so
- that the user can inspect this again later. */
- set_internalvar_integer (lookup_internalvar ("_exitcode"),
- (LONGEST) ecs->ws.value.integer);
+ if (ecs->ws.kind == TARGET_WAITKIND_EXITED)
+ {
+ /* Record the exit code in the convenience variable $_exitcode, so
+ that the user can inspect this again later. */
+ set_internalvar_integer (lookup_internalvar ("_exitcode"),
+ (LONGEST) ecs->ws.value.integer);
+
+ /* Also record this in the inferior itself. */
+ current_inferior ()->has_exit_code = 1;
+ current_inferior ()->exit_code = (LONGEST) ecs->ws.value.integer;
- /* Also record this in the inferior itself. */
- current_inferior ()->has_exit_code = 1;
- current_inferior ()->exit_code = (LONGEST) ecs->ws.value.integer;
+ print_exited_reason (ecs->ws.value.integer);
+ }
+ else
+ print_signal_exited_reason (ecs->ws.value.sig);
gdb_flush (gdb_stdout);
target_mourn_inferior ();
stop_stepping (ecs);
return;
- case TARGET_WAITKIND_SIGNALLED:
- if (debug_infrun)
- fprintf_unfiltered (gdb_stdlog, "infrun: TARGET_WAITKIND_SIGNALLED\n");
- inferior_ptid = ecs->ptid;
- set_current_inferior (find_inferior_pid (ptid_get_pid (ecs->ptid)));
- set_current_program_space (current_inferior ()->pspace);
- handle_vfork_child_exec_or_exit (0);
- stop_print_frame = 0;
- target_terminal_ours (); /* Must do this before mourn anyway. */
-
- /* Note: By definition of TARGET_WAITKIND_SIGNALLED, we shouldn't
- reach here unless the inferior is dead. However, for years
- target_kill() was called here, which hints that fatal signals aren't
- really fatal on some systems. If that's true, then some changes
- may be needed. */
- target_mourn_inferior ();
-
- print_signal_exited_reason (ecs->ws.value.sig);
- singlestep_breakpoints_inserted_p = 0;
- cancel_single_step_breakpoints ();
- stop_stepping (ecs);
- return;
-
/* The following are the only cases in which we keep going;
the above cases end in a continue or goto. */
case TARGET_WAITKIND_FORKED:
case TARGET_WAITKIND_VFORKED:
if (debug_infrun)
- fprintf_unfiltered (gdb_stdlog, "infrun: TARGET_WAITKIND_FORKED\n");
+ {
+ if (ecs->ws.kind == TARGET_WAITKIND_FORKED)
+ fprintf_unfiltered (gdb_stdlog, "infrun: TARGET_WAITKIND_FORKED\n");
+ else
+ fprintf_unfiltered (gdb_stdlog, "infrun: TARGET_WAITKIND_VFORKED\n");
+ }
/* Check whether the inferior is displaced stepping. */
{
}
if (!ptid_equal (ecs->ptid, inferior_ptid))
- {
- context_switch (ecs->ptid);
- reinit_frame_cache ();
- }
+ context_switch (ecs->ptid);
/* Immediately detach breakpoints from the child before there's
any chance of letting the user delete breakpoints from the
vfork follow are detached. */
if (ecs->ws.kind != TARGET_WAITKIND_VFORKED)
{
- int child_pid = ptid_get_pid (ecs->ws.value.related_pid);
-
/* This won't actually modify the breakpoint list, but will
physically remove the breakpoints from the child. */
- detach_breakpoints (child_pid);
+ detach_breakpoints (ecs->ws.value.related_pid);
}
if (singlestep_breakpoints_inserted_p)
fprintf_unfiltered (gdb_stdlog, "infrun: TARGET_WAITKIND_EXECD\n");
if (!ptid_equal (ecs->ptid, inferior_ptid))
- {
- context_switch (ecs->ptid);
- reinit_frame_cache ();
- }
+ context_switch (ecs->ptid);
singlestep_breakpoints_inserted_p = 0;
cancel_single_step_breakpoints ();
= bpstat_stop_status (get_regcache_aspace (get_current_regcache ()),
stop_pc, ecs->ptid, &ecs->ws);
ecs->random_signal
- = !bpstat_explains_signal (ecs->event_thread->control.stop_bpstat);
+ = (bpstat_explains_signal (ecs->event_thread->control.stop_bpstat,
+ GDB_SIGNAL_TRAP)
+ == BPSTAT_SIGNAL_NO);
/* Note that this may be referenced from inside
bpstat_stop_status above, through inferior_has_execd. */
if (debug_infrun)
fprintf_unfiltered (gdb_stdlog, "infrun: TARGET_WAITKIND_NO_HISTORY\n");
/* Reverse execution: target ran out of history info. */
+
+ /* Pull the single step breakpoints out of the target. */
+ if (singlestep_breakpoints_inserted_p)
+ {
+ if (!ptid_equal (ecs->ptid, inferior_ptid))
+ context_switch (ecs->ptid);
+ remove_single_step_breakpoints ();
+ singlestep_breakpoints_inserted_p = 0;
+ }
stop_pc = regcache_read_pc (get_thread_regcache (ecs->ptid));
print_no_history_reason ();
stop_stepping (ecs);
"infrun: stepping_past_"
"singlestep_breakpoint\n");
/* Pull the single step breakpoints out of the target. */
+ if (!ptid_equal (ecs->ptid, inferior_ptid))
+ context_switch (ecs->ptid);
remove_single_step_breakpoints ();
singlestep_breakpoints_inserted_p = 0;
context_switch (saved_singlestep_ptid);
if (deprecated_context_hook)
- deprecated_context_hook (pid_to_thread_id (ecs->ptid));
+ deprecated_context_hook (pid_to_thread_id (saved_singlestep_ptid));
resume (1, GDB_SIGNAL_0);
prepare_to_wait (ecs);
/* Pull the single step breakpoints out of the target. */
if (singlestep_breakpoints_inserted_p)
{
+ if (!ptid_equal (ecs->ptid, inferior_ptid))
+ context_switch (ecs->ptid);
remove_single_step_breakpoints ();
singlestep_breakpoints_inserted_p = 0;
}
ecs->event_thread->control.trap_expected = 0;
- /* Note: We do not call context_switch at this point, as the
- context is already set up for stepping the original thread. */
- switch_to_thread (deferred_step_ptid);
+ context_switch (deferred_step_ptid);
deferred_step_ptid = null_ptid;
/* Suppress spurious "Switching to ..." message. */
previous_inferior_ptid = inferior_ptid;
skip_inline_frames call would break things. Fortunately
that's an extremely unlikely scenario. */
if (!pc_at_non_inline_function (aspace, stop_pc, &ecs->ws)
- && !(ecs->event_thread->suspend.stop_signal == GDB_SIGNAL_TRAP
- && ecs->event_thread->control.trap_expected
- && pc_at_non_inline_function (aspace,
- ecs->event_thread->prev_pc,
+ && !(ecs->event_thread->suspend.stop_signal == GDB_SIGNAL_TRAP
+ && ecs->event_thread->control.trap_expected
+ && pc_at_non_inline_function (aspace,
+ ecs->event_thread->prev_pc,
&ecs->ws)))
- skip_inline_frames (ecs->ptid);
+ {
+ skip_inline_frames (ecs->ptid);
+
+ /* Re-fetch current thread's frame in case that invalidated
+ the frame cache. */
+ frame = get_current_frame ();
+ gdbarch = get_frame_arch (frame);
+ }
}
if (ecs->event_thread->suspend.stop_signal == GDB_SIGNAL_TRAP
will be made according to the signal handling tables. */
if (ecs->event_thread->suspend.stop_signal == GDB_SIGNAL_TRAP
- || stop_soon == STOP_QUIETLY || stop_soon == STOP_QUIETLY_NO_SIGSTOP
- || stop_soon == STOP_QUIETLY_REMOTE)
+ && stop_after_trap)
{
- if (ecs->event_thread->suspend.stop_signal == GDB_SIGNAL_TRAP
- && stop_after_trap)
- {
- if (debug_infrun)
- fprintf_unfiltered (gdb_stdlog, "infrun: stopped\n");
- stop_print_frame = 0;
- stop_stepping (ecs);
- return;
- }
-
- /* This is originated from start_remote(), start_inferior() and
- shared libraries hook functions. */
- if (stop_soon == STOP_QUIETLY || stop_soon == STOP_QUIETLY_REMOTE)
- {
- if (debug_infrun)
- fprintf_unfiltered (gdb_stdlog, "infrun: quietly stopped\n");
- stop_stepping (ecs);
- return;
- }
+ if (debug_infrun)
+ fprintf_unfiltered (gdb_stdlog, "infrun: stopped\n");
+ stop_print_frame = 0;
+ stop_stepping (ecs);
+ return;
+ }
- /* This originates from attach_command(). We need to overwrite
- the stop_signal here, because some kernels don't ignore a
- SIGSTOP in a subsequent ptrace(PTRACE_CONT,SIGSTOP) call.
- See more comments in inferior.h. On the other hand, if we
- get a non-SIGSTOP, report it to the user - assume the backend
- will handle the SIGSTOP if it should show up later.
-
- Also consider that the attach is complete when we see a
- SIGTRAP. Some systems (e.g. Windows), and stubs supporting
- target extended-remote report it instead of a SIGSTOP
- (e.g. gdbserver). We already rely on SIGTRAP being our
- signal, so this is no exception.
-
- Also consider that the attach is complete when we see a
- GDB_SIGNAL_0. In non-stop mode, GDB will explicitly tell
- the target to stop all threads of the inferior, in case the
- low level attach operation doesn't stop them implicitly. If
- they weren't stopped implicitly, then the stub will report a
- GDB_SIGNAL_0, meaning: stopped for no particular reason
- other than GDB's request. */
- if (stop_soon == STOP_QUIETLY_NO_SIGSTOP
- && (ecs->event_thread->suspend.stop_signal == GDB_SIGNAL_STOP
- || ecs->event_thread->suspend.stop_signal == GDB_SIGNAL_TRAP
- || ecs->event_thread->suspend.stop_signal == GDB_SIGNAL_0))
- {
- stop_stepping (ecs);
- ecs->event_thread->suspend.stop_signal = GDB_SIGNAL_0;
- return;
- }
+ /* This is originated from start_remote(), start_inferior() and
+ shared libraries hook functions. */
+ if (stop_soon == STOP_QUIETLY || stop_soon == STOP_QUIETLY_REMOTE)
+ {
+ if (debug_infrun)
+ fprintf_unfiltered (gdb_stdlog, "infrun: quietly stopped\n");
+ stop_stepping (ecs);
+ return;
+ }
- /* See if there is a breakpoint/watchpoint/catchpoint/etc. that
- handles this event. */
- ecs->event_thread->control.stop_bpstat
- = bpstat_stop_status (get_regcache_aspace (get_current_regcache ()),
- stop_pc, ecs->ptid, &ecs->ws);
+ /* This originates from attach_command(). We need to overwrite
+ the stop_signal here, because some kernels don't ignore a
+ SIGSTOP in a subsequent ptrace(PTRACE_CONT,SIGSTOP) call.
+ See more comments in inferior.h. On the other hand, if we
+ get a non-SIGSTOP, report it to the user - assume the backend
+ will handle the SIGSTOP if it should show up later.
+
+ Also consider that the attach is complete when we see a
+ SIGTRAP. Some systems (e.g. Windows), and stubs supporting
+ target extended-remote report it instead of a SIGSTOP
+ (e.g. gdbserver). We already rely on SIGTRAP being our
+ signal, so this is no exception.
+
+ Also consider that the attach is complete when we see a
+ GDB_SIGNAL_0. In non-stop mode, GDB will explicitly tell
+ the target to stop all threads of the inferior, in case the
+ low level attach operation doesn't stop them implicitly. If
+ they weren't stopped implicitly, then the stub will report a
+ GDB_SIGNAL_0, meaning: stopped for no particular reason
+ other than GDB's request. */
+ if (stop_soon == STOP_QUIETLY_NO_SIGSTOP
+ && (ecs->event_thread->suspend.stop_signal == GDB_SIGNAL_STOP
+ || ecs->event_thread->suspend.stop_signal == GDB_SIGNAL_TRAP
+ || ecs->event_thread->suspend.stop_signal == GDB_SIGNAL_0))
+ {
+ stop_stepping (ecs);
+ ecs->event_thread->suspend.stop_signal = GDB_SIGNAL_0;
+ return;
+ }
- /* Following in case break condition called a
- function. */
- stop_print_frame = 1;
-
- /* This is where we handle "moribund" watchpoints. Unlike
- software breakpoints traps, hardware watchpoint traps are
- always distinguishable from random traps. If no high-level
- watchpoint is associated with the reported stop data address
- anymore, then the bpstat does not explain the signal ---
- simply make sure to ignore it if `stopped_by_watchpoint' is
- set. */
-
- if (debug_infrun
- && ecs->event_thread->suspend.stop_signal == GDB_SIGNAL_TRAP
- && !bpstat_explains_signal (ecs->event_thread->control.stop_bpstat)
- && stopped_by_watchpoint)
- fprintf_unfiltered (gdb_stdlog,
- "infrun: no user watchpoint explains "
- "watchpoint SIGTRAP, ignoring\n");
+ /* See if there is a breakpoint/watchpoint/catchpoint/etc. that
+ handles this event. */
+ ecs->event_thread->control.stop_bpstat
+ = bpstat_stop_status (get_regcache_aspace (get_current_regcache ()),
+ stop_pc, ecs->ptid, &ecs->ws);
- /* NOTE: cagney/2003-03-29: These two checks for a random signal
- at one stage in the past included checks for an inferior
- function call's call dummy's return breakpoint. The original
- comment, that went with the test, read:
+ /* Following in case break condition called a
+ function. */
+ stop_print_frame = 1;
- ``End of a stack dummy. Some systems (e.g. Sony news) give
- another signal besides SIGTRAP, so check here as well as
- above.''
+ /* This is where we handle "moribund" watchpoints. Unlike
+ software breakpoints traps, hardware watchpoint traps are
+ always distinguishable from random traps. If no high-level
+ watchpoint is associated with the reported stop data address
+ anymore, then the bpstat does not explain the signal ---
+ simply make sure to ignore it if `stopped_by_watchpoint' is
+ set. */
+
+ if (debug_infrun
+ && ecs->event_thread->suspend.stop_signal == GDB_SIGNAL_TRAP
+ && (bpstat_explains_signal (ecs->event_thread->control.stop_bpstat,
+ GDB_SIGNAL_TRAP)
+ == BPSTAT_SIGNAL_NO)
+ && stopped_by_watchpoint)
+ fprintf_unfiltered (gdb_stdlog,
+ "infrun: no user watchpoint explains "
+ "watchpoint SIGTRAP, ignoring\n");
- If someone ever tries to get call dummys on a
- non-executable stack to work (where the target would stop
- with something like a SIGSEGV), then those tests might need
- to be re-instated. Given, however, that the tests were only
- enabled when momentary breakpoints were not being used, I
- suspect that it won't be the case.
+ /* NOTE: cagney/2003-03-29: These two checks for a random signal
+ at one stage in the past included checks for an inferior
+ function call's call dummy's return breakpoint. The original
+ comment, that went with the test, read:
- NOTE: kettenis/2004-02-05: Indeed such checks don't seem to
- be necessary for call dummies on a non-executable stack on
- SPARC. */
+ ``End of a stack dummy. Some systems (e.g. Sony news) give
+ another signal besides SIGTRAP, so check here as well as
+ above.''
- if (ecs->event_thread->suspend.stop_signal == GDB_SIGNAL_TRAP)
- ecs->random_signal
- = !(bpstat_explains_signal (ecs->event_thread->control.stop_bpstat)
- || stopped_by_watchpoint
- || ecs->event_thread->control.trap_expected
- || (ecs->event_thread->control.step_range_end
- && (ecs->event_thread->control.step_resume_breakpoint
- == NULL)));
- else
- {
- ecs->random_signal = !bpstat_explains_signal
- (ecs->event_thread->control.stop_bpstat);
- if (!ecs->random_signal)
- ecs->event_thread->suspend.stop_signal = GDB_SIGNAL_TRAP;
- }
- }
+ If someone ever tries to get call dummys on a
+ non-executable stack to work (where the target would stop
+ with something like a SIGSEGV), then those tests might need
+ to be re-instated. Given, however, that the tests were only
+ enabled when momentary breakpoints were not being used, I
+ suspect that it won't be the case.
- /* When we reach this point, we've pretty much decided
- that the reason for stopping must've been a random
- (unexpected) signal. */
+ NOTE: kettenis/2004-02-05: Indeed such checks don't seem to
+ be necessary for call dummies on a non-executable stack on
+ SPARC. */
+ if (ecs->event_thread->suspend.stop_signal == GDB_SIGNAL_TRAP)
+ ecs->random_signal
+ = !((bpstat_explains_signal (ecs->event_thread->control.stop_bpstat,
+ GDB_SIGNAL_TRAP)
+ != BPSTAT_SIGNAL_NO)
+ || stopped_by_watchpoint
+ || ecs->event_thread->control.trap_expected
+ || (ecs->event_thread->control.step_range_end
+ && (ecs->event_thread->control.step_resume_breakpoint
+ == NULL)));
else
- ecs->random_signal = 1;
+ {
+ enum bpstat_signal_value sval;
+
+ sval = bpstat_explains_signal (ecs->event_thread->control.stop_bpstat,
+ ecs->event_thread->suspend.stop_signal);
+ ecs->random_signal = (sval == BPSTAT_SIGNAL_NO);
+
+ if (sval == BPSTAT_SIGNAL_HIDE)
+ ecs->event_thread->suspend.stop_signal = GDB_SIGNAL_TRAP;
+ }
process_event_stop_test:
if (ecs->event_thread->control.step_range_end != 0
&& ecs->event_thread->suspend.stop_signal != GDB_SIGNAL_0
- && (ecs->event_thread->control.step_range_start <= stop_pc
- && stop_pc < ecs->event_thread->control.step_range_end)
+ && pc_in_thread_step_range (stop_pc, ecs->event_thread)
&& frame_id_eq (get_stack_frame_id (frame),
ecs->event_thread->control.step_stack_frame_id)
&& ecs->event_thread->control.step_resume_breakpoint == NULL)
(leaving the inferior at the step-resume-breakpoint without
actually executing it). Either way continue until the
breakpoint is really hit. */
- keep_going (ecs);
- return;
}
+ else
+ {
+ /* Handle cases caused by hitting a breakpoint. */
- /* Handle cases caused by hitting a breakpoint. */
- {
- CORE_ADDR jmp_buf_pc;
- struct bpstat_what what;
-
- what = bpstat_what (ecs->event_thread->control.stop_bpstat);
-
- if (what.call_dummy)
- {
- stop_stack_dummy = what.call_dummy;
- }
+ CORE_ADDR jmp_buf_pc;
+ struct bpstat_what what;
- /* If we hit an internal event that triggers symbol changes, the
- current frame will be invalidated within bpstat_what (e.g., if
- we hit an internal solib event). Re-fetch it. */
- frame = get_current_frame ();
- gdbarch = get_frame_arch (frame);
+ what = bpstat_what (ecs->event_thread->control.stop_bpstat);
- switch (what.main_action)
- {
- case BPSTAT_WHAT_SET_LONGJMP_RESUME:
- /* If we hit the breakpoint at longjmp while stepping, we
- install a momentary breakpoint at the target of the
- jmp_buf. */
+ if (what.call_dummy)
+ {
+ stop_stack_dummy = what.call_dummy;
+ }
- if (debug_infrun)
- fprintf_unfiltered (gdb_stdlog,
- "infrun: BPSTAT_WHAT_SET_LONGJMP_RESUME\n");
+ /* If we hit an internal event that triggers symbol changes, the
+ current frame will be invalidated within bpstat_what (e.g.,
+ if we hit an internal solib event). Re-fetch it. */
+ frame = get_current_frame ();
+ gdbarch = get_frame_arch (frame);
- ecs->event_thread->stepping_over_breakpoint = 1;
+ switch (what.main_action)
+ {
+ case BPSTAT_WHAT_SET_LONGJMP_RESUME:
+ /* If we hit the breakpoint at longjmp while stepping, we
+ install a momentary breakpoint at the target of the
+ jmp_buf. */
- if (what.is_longjmp)
- {
- struct value *arg_value;
-
- /* If we set the longjmp breakpoint via a SystemTap probe,
- then use it to extract the arguments. The destination
- PC is the third argument to the probe. */
- arg_value = probe_safe_evaluate_at_pc (frame, 2);
- if (arg_value)
- jmp_buf_pc = value_as_address (arg_value);
- else if (!gdbarch_get_longjmp_target_p (gdbarch)
- || !gdbarch_get_longjmp_target (gdbarch,
- frame, &jmp_buf_pc))
- {
- if (debug_infrun)
- fprintf_unfiltered (gdb_stdlog,
- "infrun: BPSTAT_WHAT_SET_LONGJMP_RESUME "
- "(!gdbarch_get_longjmp_target)\n");
- keep_going (ecs);
- return;
- }
+ if (debug_infrun)
+ fprintf_unfiltered (gdb_stdlog,
+ "infrun: BPSTAT_WHAT_SET_LONGJMP_RESUME\n");
- /* We're going to replace the current step-resume breakpoint
- with a longjmp-resume breakpoint. */
- delete_step_resume_breakpoint (ecs->event_thread);
+ ecs->event_thread->stepping_over_breakpoint = 1;
- /* Insert a breakpoint at resume address. */
- insert_longjmp_resume_breakpoint (gdbarch, jmp_buf_pc);
- }
- else
- check_exception_resume (ecs, frame);
- keep_going (ecs);
- return;
+ if (what.is_longjmp)
+ {
+ struct value *arg_value;
+
+ /* If we set the longjmp breakpoint via a SystemTap
+ probe, then use it to extract the arguments. The
+ destination PC is the third argument to the
+ probe. */
+ arg_value = probe_safe_evaluate_at_pc (frame, 2);
+ if (arg_value)
+ jmp_buf_pc = value_as_address (arg_value);
+ else if (!gdbarch_get_longjmp_target_p (gdbarch)
+ || !gdbarch_get_longjmp_target (gdbarch,
+ frame, &jmp_buf_pc))
+ {
+ if (debug_infrun)
+ fprintf_unfiltered (gdb_stdlog,
+ "infrun: BPSTAT_WHAT_SET_LONGJMP_RESUME "
+ "(!gdbarch_get_longjmp_target)\n");
+ keep_going (ecs);
+ return;
+ }
- case BPSTAT_WHAT_CLEAR_LONGJMP_RESUME:
- if (debug_infrun)
- fprintf_unfiltered (gdb_stdlog,
- "infrun: BPSTAT_WHAT_CLEAR_LONGJMP_RESUME\n");
+ /* Insert a breakpoint at resume address. */
+ insert_longjmp_resume_breakpoint (gdbarch, jmp_buf_pc);
+ }
+ else
+ check_exception_resume (ecs, frame);
+ keep_going (ecs);
+ return;
- if (what.is_longjmp)
- {
- gdb_assert (ecs->event_thread->control.step_resume_breakpoint
- != NULL);
- delete_step_resume_breakpoint (ecs->event_thread);
- }
- else
+ case BPSTAT_WHAT_CLEAR_LONGJMP_RESUME:
{
+ struct frame_info *init_frame;
+
/* There are several cases to consider.
1. The initiating frame no longer exists. In this case
- we must stop, because the exception has gone too far.
+ we must stop, because the exception or longjmp has gone
+ too far.
2. The initiating frame exists, and is the same as the
- current frame. We stop, because the exception has been
- caught.
+ current frame. We stop, because the exception or
+ longjmp has been caught.
3. The initiating frame exists and is different from
- the current frame. This means the exception has been
- caught beneath the initiating frame, so keep going. */
- struct frame_info *init_frame
- = frame_find_by_id (ecs->event_thread->initiating_frame);
+ the current frame. This means the exception or longjmp
+ has been caught beneath the initiating frame, so keep
+ going.
+
+ 4. longjmp breakpoint has been placed just to protect
+ against stale dummy frames and user is not interested
+ in stopping around longjmps. */
+
+ if (debug_infrun)
+ fprintf_unfiltered (gdb_stdlog,
+ "infrun: BPSTAT_WHAT_CLEAR_LONGJMP_RESUME\n");
gdb_assert (ecs->event_thread->control.exception_resume_breakpoint
!= NULL);
delete_exception_resume_breakpoint (ecs->event_thread);
+ if (what.is_longjmp)
+ {
+ check_longjmp_breakpoint_for_call_dummy (ecs->event_thread->num);
+
+ if (!frame_id_p (ecs->event_thread->initiating_frame))
+ {
+ /* Case 4. */
+ keep_going (ecs);
+ return;
+ }
+ }
+
+ init_frame = frame_find_by_id (ecs->event_thread->initiating_frame);
+
if (init_frame)
{
struct frame_id current_id
/* For Cases 1 and 2, remove the step-resume breakpoint,
if it exists. */
delete_step_resume_breakpoint (ecs->event_thread);
+
+ ecs->event_thread->control.stop_step = 1;
+ print_end_stepping_range_reason ();
+ stop_stepping (ecs);
}
+ return;
- ecs->event_thread->control.stop_step = 1;
- print_end_stepping_range_reason ();
- stop_stepping (ecs);
- return;
-
- case BPSTAT_WHAT_SINGLE:
- if (debug_infrun)
- fprintf_unfiltered (gdb_stdlog, "infrun: BPSTAT_WHAT_SINGLE\n");
- ecs->event_thread->stepping_over_breakpoint = 1;
- /* Still need to check other stuff, at least the case
- where we are stepping and step out of the right range. */
- break;
+ case BPSTAT_WHAT_SINGLE:
+ if (debug_infrun)
+ fprintf_unfiltered (gdb_stdlog, "infrun: BPSTAT_WHAT_SINGLE\n");
+ ecs->event_thread->stepping_over_breakpoint = 1;
+ /* Still need to check other stuff, at least the case where
+ we are stepping and step out of the right range. */
+ break;
- case BPSTAT_WHAT_STEP_RESUME:
- if (debug_infrun)
- fprintf_unfiltered (gdb_stdlog, "infrun: BPSTAT_WHAT_STEP_RESUME\n");
+ case BPSTAT_WHAT_STEP_RESUME:
+ if (debug_infrun)
+ fprintf_unfiltered (gdb_stdlog, "infrun: BPSTAT_WHAT_STEP_RESUME\n");
- delete_step_resume_breakpoint (ecs->event_thread);
- if (ecs->event_thread->control.proceed_to_finish
- && execution_direction == EXEC_REVERSE)
- {
- struct thread_info *tp = ecs->event_thread;
-
- /* We are finishing a function in reverse, and just hit
- the step-resume breakpoint at the start address of the
- function, and we're almost there -- just need to back
- up by one more single-step, which should take us back
- to the function call. */
- tp->control.step_range_start = tp->control.step_range_end = 1;
- keep_going (ecs);
- return;
- }
- fill_in_stop_func (gdbarch, ecs);
- if (stop_pc == ecs->stop_func_start
- && execution_direction == EXEC_REVERSE)
- {
- /* We are stepping over a function call in reverse, and
- just hit the step-resume breakpoint at the start
- address of the function. Go back to single-stepping,
- which should take us back to the function call. */
- ecs->event_thread->stepping_over_breakpoint = 1;
- keep_going (ecs);
- return;
- }
- break;
+ delete_step_resume_breakpoint (ecs->event_thread);
+ if (ecs->event_thread->control.proceed_to_finish
+ && execution_direction == EXEC_REVERSE)
+ {
+ struct thread_info *tp = ecs->event_thread;
+
+ /* We are finishing a function in reverse, and just hit
+ the step-resume breakpoint at the start address of
+ the function, and we're almost there -- just need to
+ back up by one more single-step, which should take us
+ back to the function call. */
+ tp->control.step_range_start = tp->control.step_range_end = 1;
+ keep_going (ecs);
+ return;
+ }
+ fill_in_stop_func (gdbarch, ecs);
+ if (stop_pc == ecs->stop_func_start
+ && execution_direction == EXEC_REVERSE)
+ {
+ /* We are stepping over a function call in reverse, and
+ just hit the step-resume breakpoint at the start
+ address of the function. Go back to single-stepping,
+ which should take us back to the function call. */
+ ecs->event_thread->stepping_over_breakpoint = 1;
+ keep_going (ecs);
+ return;
+ }
+ break;
- case BPSTAT_WHAT_STOP_NOISY:
- if (debug_infrun)
- fprintf_unfiltered (gdb_stdlog, "infrun: BPSTAT_WHAT_STOP_NOISY\n");
- stop_print_frame = 1;
+ case BPSTAT_WHAT_STOP_NOISY:
+ if (debug_infrun)
+ fprintf_unfiltered (gdb_stdlog, "infrun: BPSTAT_WHAT_STOP_NOISY\n");
+ stop_print_frame = 1;
- /* We are about to nuke the step_resume_breakpointt via the
- cleanup chain, so no need to worry about it here. */
+ /* We are about to nuke the step_resume_breakpointt via the
+ cleanup chain, so no need to worry about it here. */
- stop_stepping (ecs);
- return;
+ stop_stepping (ecs);
+ return;
- case BPSTAT_WHAT_STOP_SILENT:
- if (debug_infrun)
- fprintf_unfiltered (gdb_stdlog, "infrun: BPSTAT_WHAT_STOP_SILENT\n");
- stop_print_frame = 0;
+ case BPSTAT_WHAT_STOP_SILENT:
+ if (debug_infrun)
+ fprintf_unfiltered (gdb_stdlog, "infrun: BPSTAT_WHAT_STOP_SILENT\n");
+ stop_print_frame = 0;
- /* We are about to nuke the step_resume_breakpoin via the
- cleanup chain, so no need to worry about it here. */
+ /* We are about to nuke the step_resume_breakpoin via the
+ cleanup chain, so no need to worry about it here. */
- stop_stepping (ecs);
- return;
+ stop_stepping (ecs);
+ return;
- case BPSTAT_WHAT_HP_STEP_RESUME:
- if (debug_infrun)
- fprintf_unfiltered (gdb_stdlog, "infrun: BPSTAT_WHAT_HP_STEP_RESUME\n");
+ case BPSTAT_WHAT_HP_STEP_RESUME:
+ if (debug_infrun)
+ fprintf_unfiltered (gdb_stdlog, "infrun: BPSTAT_WHAT_HP_STEP_RESUME\n");
- delete_step_resume_breakpoint (ecs->event_thread);
- if (ecs->event_thread->step_after_step_resume_breakpoint)
- {
- /* Back when the step-resume breakpoint was inserted, we
- were trying to single-step off a breakpoint. Go back
- to doing that. */
- ecs->event_thread->step_after_step_resume_breakpoint = 0;
- ecs->event_thread->stepping_over_breakpoint = 1;
- keep_going (ecs);
- return;
- }
- break;
+ delete_step_resume_breakpoint (ecs->event_thread);
+ if (ecs->event_thread->step_after_step_resume_breakpoint)
+ {
+ /* Back when the step-resume breakpoint was inserted, we
+ were trying to single-step off a breakpoint. Go back
+ to doing that. */
+ ecs->event_thread->step_after_step_resume_breakpoint = 0;
+ ecs->event_thread->stepping_over_breakpoint = 1;
+ keep_going (ecs);
+ return;
+ }
+ break;
- case BPSTAT_WHAT_KEEP_CHECKING:
- break;
- }
- }
+ case BPSTAT_WHAT_KEEP_CHECKING:
+ break;
+ }
+ }
/* We come here if we hit a breakpoint but should not
stop for it. Possibly we also were stepping
through a function epilogue and therefore must detect when
the current-frame changes in the middle of a line. */
- if (stop_pc >= ecs->event_thread->control.step_range_start
- && stop_pc < ecs->event_thread->control.step_range_end
+ if (pc_in_thread_step_range (stop_pc, ecs->event_thread)
&& (execution_direction != EXEC_REVERSE
|| frame_id_eq (get_frame_id (frame),
ecs->event_thread->control.step_frame_id)))
paddress (gdbarch, ecs->event_thread->control.step_range_start),
paddress (gdbarch, ecs->event_thread->control.step_range_end));
+ /* Tentatively re-enable range stepping; `resume' disables it if
+ necessary (e.g., if we're stepping over a breakpoint or we
+ have software watchpoints). */
+ ecs->event_thread->control.may_range_step = 1;
+
/* When stepping backward, stop at beginning of line range
(unless it's the function entry point, in which case
keep going back to the call point). */
if (execution_direction == EXEC_REVERSE)
{
- struct symtab_and_line sr_sal;
-
- /* Normal function call return (static or dynamic). */
- init_sal (&sr_sal);
- sr_sal.pc = ecs->stop_func_start;
- sr_sal.pspace = get_frame_program_space (frame);
- insert_step_resume_breakpoint_at_sal (gdbarch,
- sr_sal, null_frame_id);
+ /* If we're already at the start of the function, we've either
+ just stepped backward into a single instruction function,
+ or stepped back out of a signal handler to the first instruction
+ of the function. Just keep going, which will single-step back
+ to the caller. */
+ if (ecs->stop_func_start != stop_pc)
+ {
+ struct symtab_and_line sr_sal;
+
+ /* Normal function call return (static or dynamic). */
+ init_sal (&sr_sal);
+ sr_sal.pc = ecs->stop_func_start;
+ sr_sal.pspace = get_frame_program_space (frame);
+ insert_step_resume_breakpoint_at_sal (gdbarch,
+ sr_sal, null_frame_id);
+ }
}
else
insert_step_resume_breakpoint_at_caller (frame);
tmp_sal = find_pc_line (ecs->stop_func_start, 0);
if (tmp_sal.line != 0
- && !function_pc_is_marked_for_skip (ecs->stop_func_start))
+ && !function_name_is_marked_for_skip (ecs->stop_func_name,
+ &tmp_sal))
{
if (execution_direction == EXEC_REVERSE)
handle_step_into_function_backward (gdbarch, ecs);
if (execution_direction == EXEC_REVERSE)
{
- /* Set a breakpoint at callee's start address.
- From there we can step once and be back in the caller. */
- struct symtab_and_line sr_sal;
+ /* If we're already at the start of the function, we've either just
+ stepped backward into a single instruction function without line
+ number info, or stepped back out of a signal handler to the first
+ instruction of the function without line number info. Just keep
+ going, which will single-step back to the caller. */
+ if (ecs->stop_func_start != stop_pc)
+ {
+ /* Set a breakpoint at callee's start address.
+ From there we can step once and be back in the caller. */
+ struct symtab_and_line sr_sal;
- init_sal (&sr_sal);
- sr_sal.pc = ecs->stop_func_start;
- sr_sal.pspace = get_frame_program_space (frame);
- insert_step_resume_breakpoint_at_sal (gdbarch,
- sr_sal, null_frame_id);
+ init_sal (&sr_sal);
+ sr_sal.pc = ecs->stop_func_start;
+ sr_sal.pspace = get_frame_program_space (frame);
+ insert_step_resume_breakpoint_at_sal (gdbarch,
+ sr_sal, null_frame_id);
+ }
}
else
/* Set a breakpoint at callee's return address (the address
ecs->event_thread->control.step_range_start = stop_pc_sal.pc;
ecs->event_thread->control.step_range_end = stop_pc_sal.end;
+ ecs->event_thread->control.may_range_step = 1;
set_step_info (frame, stop_pc_sal);
if (debug_infrun)
static void
insert_longjmp_resume_breakpoint (struct gdbarch *gdbarch, CORE_ADDR pc)
{
- /* There should never be more than one step-resume or longjmp-resume
- breakpoint per thread, so we should never be setting a new
+ /* There should never be more than one longjmp-resume breakpoint per
+ thread, so we should never be setting a new
longjmp_resume_breakpoint when one is already active. */
- gdb_assert (inferior_thread ()->control.step_resume_breakpoint == NULL);
+ gdb_assert (inferior_thread ()->control.exception_resume_breakpoint == NULL);
if (debug_infrun)
fprintf_unfiltered (gdb_stdlog,
"infrun: inserting longjmp-resume breakpoint at %s\n",
paddress (gdbarch, pc));
- inferior_thread ()->control.step_resume_breakpoint =
+ inferior_thread ()->control.exception_resume_breakpoint =
set_momentary_breakpoint_at_pc (gdbarch, pc, bp_longjmp_resume);
}
static void
insert_exception_resume_from_probe (struct thread_info *tp,
const struct probe *probe,
- struct objfile *objfile,
struct frame_info *frame)
{
struct value *arg_value;
if (debug_infrun)
fprintf_unfiltered (gdb_stdlog,
"infrun: exception resume at %s\n",
- paddress (get_objfile_arch (objfile),
+ paddress (get_objfile_arch (probe->objfile),
handler));
bp = set_momentary_breakpoint_at_pc (get_frame_arch (frame),
struct frame_info *frame)
{
volatile struct gdb_exception e;
- struct objfile *objfile;
const struct probe *probe;
struct symbol *func;
SystemTap probe point. If so, the probe has two arguments: the
CFA and the HANDLER. We ignore the CFA, extract the handler, and
set a breakpoint there. */
- probe = find_probe_by_pc (get_frame_pc (frame), &objfile);
+ probe = find_probe_by_pc (get_frame_pc (frame));
if (probe)
{
- insert_exception_resume_from_probe (ecs->event_thread, probe,
- objfile, frame);
+ insert_exception_resume_from_probe (ecs->event_thread, probe, frame);
return;
}
signal_pass[signo] = (signal_stop[signo] == 0
&& signal_print[signo] == 0
- && signal_program[signo] == 1);
+ && signal_program[signo] == 1
+ && signal_catch[signo] == 0);
}
int
return ret;
}
+/* Update the global 'signal_catch' from INFO and notify the
+ target. */
+
+void
+signal_catch_update (const unsigned int *info)
+{
+ int i;
+
+ for (i = 0; i < GDB_SIGNAL_LAST; ++i)
+ signal_catch[i] = info[i] > 0;
+ signal_cache_update (-1);
+ target_pass_signals ((int) GDB_SIGNAL_LAST, signal_pass);
+}
+
static void
sig_print_header (void)
{
do_cleanups (old_chain);
}
+/* Complete the "handle" command. */
+
+static VEC (char_ptr) *
+handle_completer (struct cmd_list_element *ignore,
+ const char *text, const char *word)
+{
+ VEC (char_ptr) *vec_signals, *vec_keywords, *return_val;
+ static const char * const keywords[] =
+ {
+ "all",
+ "stop",
+ "ignore",
+ "print",
+ "pass",
+ "nostop",
+ "noignore",
+ "noprint",
+ "nopass",
+ NULL,
+ };
+
+ vec_signals = signal_completer (ignore, text, word);
+ vec_keywords = complete_on_enum (keywords, word, word);
+
+ return_val = VEC_merge (char_ptr, vec_signals, vec_keywords);
+ VEC_free (char_ptr, vec_signals);
+ VEC_free (char_ptr, vec_keywords);
+ return return_val;
+}
+
static void
xdb_handle_command (char *args, int from_tty)
{
struct infcall_suspend_state
{
struct thread_suspend_state thread_suspend;
+#if 0 /* Currently unused and empty structures are not valid C. */
struct inferior_suspend_state inferior_suspend;
+#endif
/* Other fields: */
CORE_ADDR stop_pc;
{
struct infcall_suspend_state *inf_state;
struct thread_info *tp = inferior_thread ();
+#if 0
struct inferior *inf = current_inferior ();
+#endif
struct regcache *regcache = get_current_regcache ();
struct gdbarch *gdbarch = get_regcache_arch (regcache);
gdb_byte *siginfo_data = NULL;
}
inf_state->thread_suspend = tp->suspend;
+#if 0 /* Currently unused and empty structures are not valid C. */
inf_state->inferior_suspend = inf->suspend;
+#endif
/* run_inferior_call will not use the signal due to its `proceed' call with
GDB_SIGNAL_0 anyway. */
restore_infcall_suspend_state (struct infcall_suspend_state *inf_state)
{
struct thread_info *tp = inferior_thread ();
+#if 0
struct inferior *inf = current_inferior ();
+#endif
struct regcache *regcache = get_current_regcache ();
struct gdbarch *gdbarch = get_regcache_arch (regcache);
tp->suspend = inf_state->thread_suspend;
+#if 0 /* Currently unused and empty structures are not valid C. */
inf->suspend = inf_state->inferior_suspend;
+#endif
stop_pc = inf_state->stop_pc;
if (inf_state->siginfo_gdbarch == gdbarch)
{
struct type *type = gdbarch_get_siginfo_type (gdbarch);
- size_t len = TYPE_LENGTH (type);
/* Errors ignored. */
target_write (¤t_target, TARGET_OBJECT_SIGNAL_INFO, NULL,
- inf_state->siginfo_data, 0, len);
+ inf_state->siginfo_data, 0, TYPE_LENGTH (type));
}
/* The inferior can be gone if the user types "print exit(0)"
}
}
-/* User interface for non-stop mode. */
-
-int non_stop = 0;
-
-static void
-set_non_stop (char *args, int from_tty,
- struct cmd_list_element *c)
-{
- if (target_has_execution)
- {
- non_stop_1 = non_stop;
- error (_("Cannot change this setting while the inferior is running."));
- }
-
- non_stop = non_stop_1;
-}
-
-static void
-show_non_stop (struct ui_file *file, int from_tty,
- struct cmd_list_element *c, const char *value)
-{
- fprintf_filtered (file,
- _("Controlling the inferior in non-stop mode is %s.\n"),
- value);
-}
-
static void
show_schedule_multiple (struct ui_file *file, int from_tty,
struct cmd_list_element *c, const char *value)
{
int i;
int numsigs;
+ struct cmd_list_element *c;
add_info ("signals", signals_info, _("\
What debugger does when program gets various signals.\n\
Specify a signal as argument to print info on that signal only."));
add_info_alias ("handle", "signals", 0);
- add_com ("handle", class_run, handle_command, _("\
-Specify how to handle a signal.\n\
+ c = add_com ("handle", class_run, handle_command, _("\
+Specify how to handle signals.\n\
+Usage: handle SIGNAL [ACTIONS]\n\
Args are signals and actions to apply to those signals.\n\
+If no actions are specified, the current settings for the specified signals\n\
+will be displayed instead.\n\
+\n\
Symbolic signals (e.g. SIGSEGV) are recommended but numeric signals\n\
from 1-15 are allowed for compatibility with old versions of GDB.\n\
Numeric ranges may be specified with the form LOW-HIGH (e.g. 1-5).\n\
The special arg \"all\" is recognized to mean all signals except those\n\
used by the debugger, typically SIGTRAP and SIGINT.\n\
+\n\
Recognized actions include \"stop\", \"nostop\", \"print\", \"noprint\",\n\
\"pass\", \"nopass\", \"ignore\", or \"noignore\".\n\
Stop means reenter debugger if this signal happens (implies print).\n\
Print means print a message if this signal happens.\n\
Pass means let program see this signal; otherwise program doesn't know.\n\
Ignore is a synonym for nopass and noignore is a synonym for pass.\n\
-Pass and Stop may be combined."));
+Pass and Stop may be combined.\n\
+\n\
+Multiple signals may be specified. Signal numbers and signal names\n\
+may be interspersed with actions, with the actions being performed for\n\
+all signals cumulatively specified."));
+ set_cmd_completer (c, handle_completer);
+
if (xdb_commands)
{
add_com ("lz", class_info, signals_info, _("\
This allows you to set a list of commands to be run each time execution\n\
of the program stops."), &cmdlist);
- add_setshow_zinteger_cmd ("infrun", class_maintenance, &debug_infrun, _("\
+ add_setshow_zuinteger_cmd ("infrun", class_maintenance, &debug_infrun, _("\
Set inferior debugging."), _("\
Show inferior debugging."), _("\
When non-zero, inferior specific debugging is enabled."),
- NULL,
- show_debug_infrun,
- &setdebuglist, &showdebuglist);
+ NULL,
+ show_debug_infrun,
+ &setdebuglist, &showdebuglist);
add_setshow_boolean_cmd ("displaced", class_maintenance,
&debug_displaced, _("\
xmalloc (sizeof (signal_print[0]) * numsigs);
signal_program = (unsigned char *)
xmalloc (sizeof (signal_program[0]) * numsigs);
+ signal_catch = (unsigned char *)
+ xmalloc (sizeof (signal_catch[0]) * numsigs);
signal_pass = (unsigned char *)
xmalloc (sizeof (signal_program[0]) * numsigs);
for (i = 0; i < numsigs; i++)
signal_stop[i] = 1;
signal_print[i] = 1;
signal_program[i] = 1;
+ signal_catch[i] = 0;
}
/* Signals caused by debugger's own actions
If nonzero, gdb will give control to the user when the dynamic linker\n\
notifies gdb of shared library events. The most common event of interest\n\
to the user would be loading/unloading of a new library."),
- NULL,
+ set_stop_on_solib_events,
show_stop_on_solib_events,
&setlist, &showlist);
show_step_stop_if_no_debug,
&setlist, &showlist);
- add_setshow_enum_cmd ("displaced-stepping", class_run,
- can_use_displaced_stepping_enum,
- &can_use_displaced_stepping, _("\
+ add_setshow_auto_boolean_cmd ("displaced-stepping", class_run,
+ &can_use_displaced_stepping, _("\
Set debugger's willingness to use displaced stepping."), _("\
Show debugger's willingness to use displaced stepping."), _("\
If on, gdb will use displaced stepping to step over breakpoints if it is\n\
architecture. If auto (which is the default), gdb will use displaced stepping\n\
if the target architecture supports it and non-stop mode is active, but will not\n\
use it in all-stop mode (see help set non-stop)."),
- NULL,
- show_can_use_displaced_stepping,
- &setlist, &showlist);
+ NULL,
+ show_can_use_displaced_stepping,
+ &setlist, &showlist);
add_setshow_enum_cmd ("exec-direction", class_run, exec_direction_names,
&exec_direction, _("Set direction of execution.\n\
projects / deliverable / binutils-gdb.git / blobdiff