-/* Remote debugging interface for Hitachi E7000 ICE, for GDB
- Copyright 1993, 1994, 1996, 1997, 1998 Free Software Foundation, Inc.
+/* Remote debugging interface for Renesas E7000 ICE, for GDB
+
+ Copyright (C) 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000, 2001, 2002,
+ 2003, 2004, 2006, 2007 Free Software Foundation, Inc.
+
Contributed by Cygnus Support.
Written by Steve Chamberlain for Cygnus Support.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
- Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. */
+ Foundation, Inc., 51 Franklin Street, Fifth Floor,
+ Boston, MA 02110-1301, USA. */
-/* The E7000 is an in-circuit emulator for the Hitachi H8/300-H and
- Hitachi-SH processor. It has serial port and a lan port.
+/* The E7000 is an in-circuit emulator for the Renesas H8/300-H and
+ Renesas-SH processor. It has serial port and a lan port.
The monitor command set makes it difficult to load large ammounts of
data over the lan without using ftp - so try not to issue load
#include "defs.h"
#include "gdbcore.h"
+#include "gdbarch.h"
#include "inferior.h"
#include "target.h"
-#include "wait.h"
#include "value.h"
#include "command.h"
-#include <signal.h>
#include "gdb_string.h"
+#include "exceptions.h"
#include "gdbcmd.h"
#include <sys/types.h>
#include "serial.h"
#include "remote-utils.h"
#include "symfile.h"
+#include "regcache.h"
#include <time.h>
#include <ctype.h>
#define ACK 0x06
#define CTRLZ 0x1a
-extern void notice_quit PARAMS ((void));
+/* This file is used by 2 different targets, sh-elf and h8300. The
+ h8300 is not multiarched and doesn't use the registers defined in
+ tm-sh.h. To avoid using a macro GDB_TARGET_IS_SH, we do runtime check
+ of the target, which requires that these namse below are always
+ defined also in the h8300 case. */
-extern void report_transfer_performance PARAMS ((unsigned long,
- time_t, time_t));
+#if !defined (PR_REGNUM)
+#define PR_REGNUM -1
+#endif
+#if !defined (GBR_REGNUM)
+#define GBR_REGNUM -1
+#endif
+#if !defined (VBR_REGNUM)
+#define VBR_REGNUM -1
+#endif
+#if !defined (MACH_REGNUM)
+#define MACH_REGNUM -1
+#endif
+#if !defined (MACL_REGNUM)
+#define MACL_REGNUM -1
+#endif
+#if !defined (SR_REGNUM)
+#define SR_REGNUM -1
+#endif
+
+extern void report_transfer_performance (unsigned long, time_t, time_t);
extern char *sh_processor_type;
/* Local function declarations. */
-static void e7000_close PARAMS ((int));
+static void e7000_close (int);
-static void e7000_fetch_register PARAMS ((int));
+static void e7000_fetch_register (int);
-static void e7000_store_register PARAMS ((int));
+static void e7000_store_register (int);
-static void e7000_command PARAMS ((char *, int));
+static void e7000_command (char *, int);
-static void e7000_login_command PARAMS ((char *, int));
+static void e7000_login_command (char *, int);
-static void e7000_ftp_command PARAMS ((char *, int));
+static void e7000_ftp_command (char *, int);
-static void e7000_drain_command PARAMS ((char *, int));
+static void e7000_drain_command (char *, int);
-static void expect PARAMS ((char *));
+static void expect (char *);
-static void expect_full_prompt PARAMS ((void));
+static void expect_full_prompt (void);
-static void expect_prompt PARAMS ((void));
+static void expect_prompt (void);
-static int e7000_parse_device PARAMS ((char *args, char *dev_name,
- int baudrate));
+static int e7000_parse_device (char *args, char *dev_name, int baudrate);
/* Variables. */
-static serial_t e7000_desc;
+static struct serial *e7000_desc;
/* Allow user to chose between using hardware breakpoints or memory. */
-static int use_hard_breakpoints = 0; /* use sw breakpoints by default */
+static int use_hard_breakpoints = 0; /* use sw breakpoints by default */
/* Nonzero if using the tcp serial driver. */
-static int using_tcp; /* direct tcp connection to target */
+static int using_tcp; /* direct tcp connection to target */
static int using_tcp_remote; /* indirect connection to target
via tcp to controller */
/* Send data to e7000debug. */
static void
-puts_e7000debug (buf)
- char *buf;
+puts_e7000debug (char *buf)
{
if (!e7000_desc)
- error ("Use \"target e7000 ...\" first.");
+ error (_("Use \"target e7000 ...\" first."));
if (remote_debug)
printf_unfiltered ("Sending %s\n", buf);
- if (SERIAL_WRITE (e7000_desc, buf, strlen (buf)))
- fprintf_unfiltered (gdb_stderr, "SERIAL_WRITE failed: %s\n", safe_strerror (errno));
+ if (serial_write (e7000_desc, buf, strlen (buf)))
+ fprintf_unfiltered (gdb_stderr, "serial_write failed: %s\n", safe_strerror (errno));
/* And expect to see it echoed, unless using the pc interface */
#if 0
}
static void
-putchar_e7000 (x)
- int x;
+putchar_e7000 (int x)
{
char b[1];
b[0] = x;
- SERIAL_WRITE (e7000_desc, b, 1);
+ serial_write (e7000_desc, b, 1);
}
static void
-write_e7000 (s)
- char *s;
+write_e7000 (char *s)
{
- SERIAL_WRITE (e7000_desc, s, strlen (s));
+ serial_write (e7000_desc, s, strlen (s));
}
static int
-normal (x)
- int x;
+normal (int x)
{
if (x == '\n')
return '\r';
returns -1, else returns next char. Discards chars > 127. */
static int
-readchar (timeout)
- int timeout;
+readchar (int timeout)
{
int c;
do
{
- c = SERIAL_READCHAR (e7000_desc, timeout);
+ c = serial_readchar (e7000_desc, timeout);
}
while (c > 127);
if (timeout == 0)
return -1;
echo = 0;
- error ("Timeout reading from remote system.");
+ error (_("Timeout reading from remote system."));
}
else if (c < 0)
- error ("Serial communication error");
+ error (_("Serial communication error"));
- if (remote_debug)
+ if (remote_debug)
{
putchar_unfiltered (c);
gdb_flush (gdb_stdout);
#if 0
char *
-tl (x)
+tl (int x)
{
static char b[8][10];
static int p;
p++;
p &= 7;
- if (x >= ' ')
- {
+ if (x >= ' ')
+ {
b[p][0] = x;
b[p][1] = 0;
}
else
{
- sprintf(b[p], "<%d>", x);
+ sprintf (b[p], "<%d>", x);
}
return b[p];
out. Let the user break out immediately. */
static void
-expect (string)
- char *string;
+expect (char *string)
{
char *p = string;
int c;
while (1)
{
c = readchar (timeout);
-#if 0
- notice_quit ();
- if (quit_flag == 1)
- {
- if (ctrl_c)
- {
- putchar_e7000(CTRLC);
- --ctrl_c;
- }
- else
- {
- quit ();
- }
- }
-#endif
-
+
if (echo)
{
if (c == '\r' || c == '\n')
into states from which we can't recover. */
static void
-expect_prompt ()
+expect_prompt (void)
{
expect (":");
}
static void
-expect_full_prompt ()
+expect_full_prompt (void)
{
expect ("\r:");
}
static int
-convert_hex_digit (ch)
- int ch;
+convert_hex_digit (int ch)
{
if (ch >= '0' && ch <= '9')
return ch - '0';
}
static int
-get_hex (start)
- int *start;
+get_hex (int *start)
{
int value = convert_hex_digit (*start);
int try;
them in registers starting at REGNO. */
static void
-get_hex_regs (n, regno)
- int n;
- int regno;
+get_hex_regs (int n, int regno)
{
long val;
int i;
val = 0;
for (j = 0; j < 8; j++)
val = (val << 4) + get_hex_digit (j == 0);
- supply_register (regno++, (char *) &val);
+ regcache_raw_supply (current_regcache, regno++, (char *) &val);
}
}
#endif
user types "run" after having attached. */
static void
-e7000_create_inferior (execfile, args, env)
- char *execfile;
- char *args;
- char **env;
+e7000_create_inferior (char *execfile, char *args, char **env,
+ int from_tty)
{
int entry_pt;
if (args && *args)
- error ("Can't pass arguments to remote E7000DEBUG process");
+ error (_("Can't pass arguments to remote E7000DEBUG process"));
if (execfile == 0 || exec_bfd == 0)
- error ("No executable file specified");
+ error (_("No executable file specified"));
entry_pt = (int) bfd_get_start_address (exec_bfd);
target_terminal_inferior ();
/* insert_step_breakpoint (); FIXME, do we need this? */
- proceed ((CORE_ADDR) entry_pt, -1, 0); /* Let 'er rip... */
+ write_pc ((CORE_ADDR) entry_pt);
}
/* Open a connection to a remote debugger. NAME is the filename used
/* Grab the next token and buy some space for it */
static char *
-next (ptr)
- char **ptr;
+next (char **ptr)
{
char *p = *ptr;
char *s;
}
static void
-e7000_login_command (args, from_tty)
- char *args;
- int from_tty;
+e7000_login_command (char *args, int from_tty)
{
if (args)
{
}
else
{
- error ("Syntax is ftplogin <machine> <user> <passwd> <directory>");
+ error (_("Syntax is ftplogin <machine> <user> <passwd> <directory>"));
}
}
/* Start an ftp transfer from the E7000 to a host */
static void
-e7000_ftp_command (args, from_tty)
- char *args;
- int from_tty;
+e7000_ftp_command (char *args, int from_tty)
{
/* FIXME: arbitrary limit on machine names and such. */
char buf[200];
timeout = oldtimeout;
}
-static int
-e7000_parse_device (args, dev_name, baudrate)
- char *args;
- char *dev_name;
- int baudrate;
+static int
+e7000_parse_device (char *args, char *dev_name, int baudrate)
{
char junk[128];
int n = 0;
strcpy (dev_name, args);
using_pc = 1;
}
- else
+ else
{
/* FIXME! temp hack to allow use with port master -
- target tcp_remote <device> */
- if (args && strncmp (args, "tcp", 10) == 0)
- {
+ target tcp_remote <device> */
+ if (args && strncmp (args, "tcp", 10) == 0)
+ {
char com_type[128];
n = sscanf (args, " %s %s %d %s", com_type, dev_name, &baudrate, junk);
- using_tcp_remote=1;
+ using_tcp_remote = 1;
n--;
- }
- else if (args)
+ }
+ else if (args)
{
n = sscanf (args, " %s %d %s", dev_name, &baudrate, junk);
}
if (n != 1 && n != 2)
{
- error ("Bad arguments. Usage:\ttarget e7000 <device> <speed>\n\
+ error (_("Bad arguments. Usage:\ttarget e7000 <device> <speed>\n\
or \t\ttarget e7000 <host>[:<port>]\n\
or \t\ttarget e7000 tcp_remote <host>[:<port>]\n\
-or \t\ttarget e7000 pc\n");
+or \t\ttarget e7000 pc\n"));
}
-#if !defined(__GO32__) && !defined(_WIN32)
+#if !defined(__GO32__) && !defined(_WIN32) && !defined(__CYGWIN__)
/* FIXME! test for ':' is ambiguous */
if (n == 1 && strchr (dev_name, ':') == 0)
{
}
#endif
if (!using_tcp_remote && strchr (dev_name, ':'))
- using_tcp = 1;
+ using_tcp = 1;
}
return n;
/* Stub for catch_errors. */
static int
-e7000_start_remote (dummy)
- char *dummy;
+e7000_start_remote (void *dummy)
{
int loop;
int sync;
int try;
int quit_trying;
- immediate_quit = 1; /* Allow user to interrupt it */
+ immediate_quit++; /* Allow user to interrupt it */
/* Hello? Are you there? */
sync = 0;
- loop = 0;
+ loop = 0;
try = 0;
quit_trying = 20;
putchar_e7000 (CTRLC);
if (c == ':')
sync = 1;
- if (loop++ == 20)
+ if (loop++ == 20)
{
putchar_e7000 (CTRLC);
loop = 0;
}
- QUIT ;
+ QUIT;
if (quit_flag)
{
putchar_e7000 (CTRLC);
/* Was-> quit_flag = 0; */
c = -1;
- quit_trying = try+1; /* we don't want to try anymore */
+ quit_trying = try + 1; /* we don't want to try anymore */
}
else
{
if (!sync)
{
- fprintf_unfiltered (gdb_stderr, "Giving up after %d tries...\n",try);
- error ("Unable to syncronize with target.\n");
+ fprintf_unfiltered (gdb_stderr, "Giving up after %d tries...\n", try);
+ error (_("Unable to synchronize with target."));
}
puts_e7000debug ("\r");
puts_e7000debug ("b -\r"); /* Clear breakpoints */
expect_prompt ();
- immediate_quit = 0;
+ immediate_quit--;
/* This is really the job of start_remote however, that makes an assumption
that the target is about to print out a status message of some sort. That
flush_cached_frames ();
registers_changed ();
stop_pc = read_pc ();
- set_current_frame (create_new_frame (read_fp (), stop_pc));
- select_frame (get_current_frame (), 0);
- print_stack_frame (selected_frame, -1, 1);
+ print_stack_frame (get_selected_frame (NULL), 0, SRC_AND_LOC);
return 1;
}
static void
-e7000_open (args, from_tty)
- char *args;
- int from_tty;
+e7000_open (char *args, int from_tty)
{
int n;
push_target (&e7000_ops);
- e7000_desc = SERIAL_OPEN (dev_name);
+ e7000_desc = serial_open (dev_name);
if (!e7000_desc)
perror_with_name (dev_name);
- SERIAL_SETBAUDRATE (e7000_desc, baudrate);
- SERIAL_RAW (e7000_desc);
-
-#ifdef GDB_TARGET_IS_H8300
- h8300hmode = 1;
-#endif
+ if (serial_setbaudrate (e7000_desc, baudrate))
+ {
+ serial_close (e7000_desc);
+ perror_with_name (dev_name);
+ }
+ serial_raw (e7000_desc);
/* Start the remote connection; if error (0), discard this target.
In particular, if the user quits, be sure to discard it
(we'd be in an inconsistent state otherwise). */
- if (!catch_errors (e7000_start_remote, (char *)0,
- "Couldn't establish connection to remote target\n", RETURN_MASK_ALL))
- if (from_tty)
- printf_filtered ("Remote target %s connected to %s\n", target_shortname,
- dev_name);
+ if (!catch_errors (e7000_start_remote, (char *) 0,
+ "Couldn't establish connection to remote target\n", RETURN_MASK_ALL))
+ if (from_tty)
+ printf_filtered ("Remote target %s connected to %s\n", target_shortname,
+ dev_name);
}
/* Close out all files and local state before this target loses control. */
static void
-e7000_close (quitting)
- int quitting;
+e7000_close (int quitting)
{
if (e7000_desc)
{
- SERIAL_CLOSE (e7000_desc);
+ serial_close (e7000_desc);
e7000_desc = 0;
}
}
when you want to detach and do something else with your gdb. */
static void
-e7000_detach (from_tty)
- int from_tty;
+e7000_detach (char *arg, int from_tty)
{
pop_target (); /* calls e7000_close to do the real work */
if (from_tty)
/* Tell the remote machine to resume. */
static void
-e7000_resume (pid, step, sig)
- int pid, step, sig;
+e7000_resume (ptid_t ptid, int step, enum target_signal sigal)
{
if (step)
puts_e7000debug ("S\r");
000218 MOV.B R1L,R2L
STEP NORMAL END or
BREAK POINT
- */
-
-#ifdef GDB_TARGET_IS_H8300
+ */
char *want_h8300h = "PC=%p CCR=%c\n\
ER0 - ER3 %0 %1 %2 %3\n\
ER0 - ER3 %0 %1 %2 %3\n\
ER4 - ER7 %4 %5 %6 %7";
-#endif
-
-#ifdef GDB_TARGET_IS_SH
-
-char *want = "PC=%16 SR=%22\n\
+char *want_sh = "PC=%16 SR=%22\n\
PR=%17 GBR=%18 VBR=%19\n\
MACH=%20 MACL=%21\n\
R0-7 %0 %1 %2 %3 %4 %5 %6 %7\n\
R8-15 %8 %9 %10 %11 %12 %13 %14 %15\n";
-char *want_nopc = "%16 SR=%22\n\
+char *want_nopc_sh = "%16 SR=%22\n\
PR=%17 GBR=%18 VBR=%19\n\
MACH=%20 MACL=%21\n\
R0-7 %0 %1 %2 %3 %4 %5 %6 %7\n\
R0_BANK1-R3_BANK1 %33 %34 %35 %36\n\
R4_BANK1-R7_BANK1 %37 %38 %39 %40";
-char *want_sh3_nopc = "%16 SR=%22\n\
+char *want_nopc_sh3 = "%16 SR=%22\n\
PR=%17 GBR=%18 VBR=%19\n\
MACH=%20 MACL=%21 SSR=%22 SPC=%23\n\
R0-7 %0 %1 %2 %3 %4 %5 %6 %7\n\
R0_BANK1-R3_BANK1 %33 %34 %35 %36\n\
R4_BANK1-R7_BANK1 %37 %38 %39 %40";
-#endif
-
static int
-gch ()
+gch (void)
{
return readchar (timeout);
}
static unsigned int
-gbyte ()
+gbyte (void)
{
int high = convert_hex_digit (gch ());
int low = convert_hex_digit (gch ());
return (high << 4) + low;
}
-void
-fetch_regs_from_dump (nextchar, want)
- int (*nextchar)();
- char *want;
+static void
+fetch_regs_from_dump (int (*nextchar) (), char *want)
{
int regno;
- char buf[MAX_REGISTER_RAW_SIZE];
+ char buf[MAX_REGISTER_SIZE];
int thischar = nextchar ();
+ if (want == NULL)
+ internal_error (__FILE__, __LINE__, _("Register set not selected."));
+
while (*want)
{
switch (*want)
{
case '\n':
/* Skip to end of line and then eat all new line type stuff */
- while (thischar != '\n' && thischar != '\r')
+ while (thischar != '\n' && thischar != '\r')
thischar = nextchar ();
- while (thischar == '\n' || thischar == '\r')
+ while (thischar == '\n' || thischar == '\r')
thischar = nextchar ();
want++;
break;
thischar = nextchar ();
want++;
break;
-
+
default:
if (*want == thischar)
{
want++;
if (*want)
thischar = nextchar ();
-
+
}
else if (thischar == ' ' || thischar == '\n' || thischar == '\r')
{
thischar = nextchar ();
}
- else {
- error ("out of sync in fetch registers wanted <%s>, got <%c 0x%x>",
- want, thischar, thischar);
- }
-
+ else
+ {
+ error (_("out of sync in fetch registers wanted <%s>, got <%c 0x%x>"),
+ want, thischar, thischar);
+ }
+
break;
case '%':
/* Got a register command */
want++;
break;
#endif
-#ifdef FP_REGNUM
+#ifdef DEPRECATED_FP_REGNUM
case 'f':
- regno = FP_REGNUM;
+ regno = DEPRECATED_FP_REGNUM;
want++;
break;
#endif
default:
- if (isdigit (want[0]))
+ if (isdigit (want[0]))
{
if (isdigit (want[1]))
{
regno = (want[0] - '0') * 10 + want[1] - '0';
want += 2;
}
- else
+ else
{
regno = want[0] - '0';
want++;
}
}
-
+
else
- abort ();
+ internal_error (__FILE__, __LINE__, _("failed internal consistency check"));
}
store_signed_integer (buf,
- REGISTER_RAW_SIZE(regno),
- (LONGEST) get_hex (&thischar, nextchar));
- supply_register (regno, buf);
+ register_size (current_gdbarch, regno),
+ (LONGEST) get_hex (&thischar));
+ regcache_raw_supply (current_regcache, regno, buf);
break;
}
}
}
static void
-e7000_fetch_registers ()
+e7000_fetch_registers (void)
{
int regno;
- char *wanted;
+ char *wanted = NULL;
+ int realregs = 0;
puts_e7000debug ("R\r");
-#ifdef GDB_TARGET_IS_SH
- wanted = want;
if (TARGET_ARCHITECTURE->arch == bfd_arch_sh)
- switch (TARGET_ARCHITECTURE->mach)
- {
- case bfd_mach_sh3:
- case bfd_mach_sh3e:
- case bfd_mach_sh4:
- wanted = want_sh3;
- }
-#else
- if (h8300smode)
- wanted = want_h8300s;
- else
- wanted = want_h8300h;
-#endif
+ {
+ wanted = want_sh;
+ realregs = 59;
+ switch (TARGET_ARCHITECTURE->mach)
+ {
+ case bfd_mach_sh3:
+ case bfd_mach_sh3e:
+ case bfd_mach_sh4:
+ wanted = want_sh3;
+ }
+ }
+ if (TARGET_ARCHITECTURE->arch == bfd_arch_h8300)
+ {
+ wanted = want_h8300h;
+ realregs = 10;
+ switch (TARGET_ARCHITECTURE->mach)
+ {
+ case bfd_mach_h8300s:
+ case bfd_mach_h8300sn:
+ case bfd_mach_h8300sx:
+ case bfd_mach_h8300sxn:
+ wanted = want_h8300s;
+ realregs = 11;
+ }
+ }
+
fetch_regs_from_dump (gch, wanted);
/* And supply the extra ones the simulator uses */
- for (regno = NUM_REALREGS; regno < NUM_REGS; regno++)
+ for (regno = realregs; regno < NUM_REGS; regno++)
{
int buf = 0;
- supply_register (regno, (char *) (&buf));
+ regcache_raw_supply (current_regcache, regno, (char *) (&buf));
}
}
errno value. */
static void
-e7000_fetch_register (regno)
- int regno;
+e7000_fetch_register (int regno)
{
e7000_fetch_registers ();
}
/* Store the remote registers from the contents of the block REGS. */
static void
-e7000_store_registers ()
+e7000_store_registers (void)
{
int regno;
+ int realregs = 0;
- for (regno = 0; regno < NUM_REALREGS; regno++)
+ if (TARGET_ARCHITECTURE->arch == bfd_arch_sh)
+ realregs = 59;
+ if (TARGET_ARCHITECTURE->arch == bfd_arch_h8300) {
+ realregs = ((TARGET_ARCHITECTURE->mach == bfd_mach_h8300s ||
+ TARGET_ARCHITECTURE->mach == bfd_mach_h8300sn ||
+ TARGET_ARCHITECTURE->mach == bfd_mach_h8300sx ||
+ TARGET_ARCHITECTURE->mach == bfd_mach_h8300sxn) ? 11 : 10);
+ }
+
+ for (regno = 0; regno < realregs; regno++)
e7000_store_register (regno);
registers_changed ();
/* Store register REGNO, or all if REGNO == 0. Return errno value. */
static void
-e7000_store_register (regno)
- int regno;
+e7000_store_register (int regno)
{
char buf[200];
return;
}
-#ifdef GDB_TARGET_IS_H8300
- if (regno <= 7)
- {
- sprintf (buf, ".ER%d %x\r", regno, read_register (regno));
- puts_e7000debug (buf);
- }
- else if (regno == PC_REGNUM)
- {
- sprintf (buf, ".PC %x\r", read_register (regno));
- puts_e7000debug (buf);
- }
- else if (regno == CCR_REGNUM)
+ if (TARGET_ARCHITECTURE->arch == bfd_arch_h8300)
{
- sprintf (buf, ".CCR %x\r", read_register (regno));
- puts_e7000debug (buf);
+ if (regno <= 7)
+ {
+ sprintf (buf, ".ER%d %s\r", regno, phex_nz (read_register (regno), 0));
+ puts_e7000debug (buf);
+ }
+ else if (regno == PC_REGNUM)
+ {
+ sprintf (buf, ".PC %s\r", phex_nz (read_register (regno), 0));
+ puts_e7000debug (buf);
+ }
+#ifdef CCR_REGNUM
+ else if (regno == CCR_REGNUM)
+ {
+ sprintf (buf, ".CCR %s\r", phex_nz (read_register (regno), 0));
+ puts_e7000debug (buf);
+ }
+#endif
}
-#endif /* GDB_TARGET_IS_H8300 */
-#ifdef GDB_TARGET_IS_SH
- switch (regno)
+ else if (TARGET_ARCHITECTURE->arch == bfd_arch_sh)
{
- default:
- sprintf (buf, ".R%d %x\r", regno, read_register (regno));
- puts_e7000debug (buf);
- break;
-
- case PC_REGNUM:
- sprintf (buf, ".PC %x\r", read_register (regno));
- puts_e7000debug (buf);
- break;
+ if (regno == PC_REGNUM)
+ {
+ sprintf (buf, ".PC %s\r", phex_nz (read_register (regno), 0));
+ puts_e7000debug (buf);
+ }
- case SR_REGNUM:
- sprintf (buf, ".SR %x\r", read_register (regno));
- puts_e7000debug (buf);
- break;
+ else if (regno == SR_REGNUM)
+ {
+ sprintf (buf, ".SR %s\r", phex_nz (read_register (regno), 0));
+ puts_e7000debug (buf);
+ }
- case PR_REGNUM:
- sprintf (buf, ".PR %x\r", read_register (regno));
- puts_e7000debug (buf);
- break;
+ else if (regno == PR_REGNUM)
+ {
+ sprintf (buf, ".PR %s\r", phex_nz (read_register (regno), 0));
+ puts_e7000debug (buf);
+ }
- case GBR_REGNUM:
- sprintf (buf, ".GBR %x\r", read_register (regno));
- puts_e7000debug (buf);
- break;
+ else if (regno == GBR_REGNUM)
+ {
+ sprintf (buf, ".GBR %s\r", phex_nz (read_register (regno), 0));
+ puts_e7000debug (buf);
+ }
- case VBR_REGNUM:
- sprintf (buf, ".VBR %x\r", read_register (regno));
- puts_e7000debug (buf);
- break;
+ else if (regno == VBR_REGNUM)
+ {
+ sprintf (buf, ".VBR %s\r", phex_nz (read_register (regno), 0));
+ puts_e7000debug (buf);
+ }
- case MACH_REGNUM:
- sprintf (buf, ".MACH %x\r", read_register (regno));
- puts_e7000debug (buf);
- break;
+ else if (regno == MACH_REGNUM)
+ {
+ sprintf (buf, ".MACH %s\r", phex_nz (read_register (regno), 0));
+ puts_e7000debug (buf);
+ }
- case MACL_REGNUM:
- sprintf (buf, ".MACL %x\r", read_register (regno));
- puts_e7000debug (buf);
- break;
+ else if (regno == MACL_REGNUM)
+ {
+ sprintf (buf, ".MACL %s\r", phex_nz (read_register (regno), 0));
+ puts_e7000debug (buf);
+ }
+ else
+ {
+ sprintf (buf, ".R%d %s\r", regno, phex_nz (read_register (regno), 0));
+ puts_e7000debug (buf);
+ }
}
-#endif /* GDB_TARGET_IS_SH */
-
expect_prompt ();
}
debugged. */
static void
-e7000_prepare_to_store ()
+e7000_prepare_to_store (void)
{
/* Do nothing, since we can store individual regs */
}
static void
-e7000_files_info ()
+e7000_files_info (struct target_ops *ops)
{
printf_unfiltered ("\tAttached to %s at %d baud.\n", dev_name, baudrate);
}
static int
-stickbyte (where, what)
- char *where;
- unsigned int what;
+stickbyte (char *where, unsigned int what)
{
static CONST char digs[] = "0123456789ABCDEF";
/* Write a small ammount of memory. */
static int
-write_small (memaddr, myaddr, len)
- CORE_ADDR memaddr;
- unsigned char *myaddr;
- int len;
+write_small (CORE_ADDR memaddr, unsigned char *myaddr, int len)
{
int i;
char buf[200];
if (((memaddr + i) & 3) == 0 && (i + 3 < len))
{
/* Can be done with a long word */
- sprintf (buf, "m %x %x%02x%02x%02x;l\r",
- memaddr + i,
+ sprintf (buf, "m %s %x%02x%02x%02x;l\r",
+ paddr_nz (memaddr + i),
myaddr[i], myaddr[i + 1], myaddr[i + 2], myaddr[i + 3]);
puts_e7000debug (buf);
i += 3;
}
else
{
- sprintf (buf, "m %x %x\r", memaddr + i, myaddr[i]);
+ sprintf (buf, "m %s %x\r", paddr_nz (memaddr + i), myaddr[i]);
puts_e7000debug (buf);
}
}
/* Write a large ammount of memory, this only works with the serial
mode enabled. Command is sent as
- il ;s:s\r ->
- <- il ;s:s\r
- <- ENQ
- ACK ->
- <- LO s\r
- Srecords...
- ^Z ->
- <- ENQ
- ACK ->
- <- :
- */
+ il ;s:s\r ->
+ <- il ;s:s\r
+ <- ENQ
+ ACK ->
+ <- LO s\r
+ Srecords...
+ ^Z ->
+ <- ENQ
+ ACK ->
+ <- :
+ */
static int
-write_large (memaddr, myaddr, len)
- CORE_ADDR memaddr;
- unsigned char *myaddr;
- int len;
+write_large (CORE_ADDR memaddr, unsigned char *myaddr, int len)
{
int i;
#define maxstride 128
compose[where++] = '\n';
compose[where++] = 0;
- SERIAL_WRITE (e7000_desc, compose, where);
+ serial_write (e7000_desc, compose, where);
j = readchar (0);
if (j == -1)
{
{
/* Hmm, it's trying to tell us something */
expect (":");
- error ("Error writing memory");
+ error (_("Error writing memory"));
}
else
{
printf_unfiltered ("@%d}@", j);
- while ((j = readchar (0)) > 0)
+ while ((j = readchar (0)) > 0)
{
- printf_unfiltered ("@{%d}@",j);
+ printf_unfiltered ("@{%d}@", j);
}
}
}
then. */
static int
-e7000_write_inferior_memory (memaddr, myaddr, len)
- CORE_ADDR memaddr;
- unsigned char *myaddr;
- int len;
+e7000_write_inferior_memory (CORE_ADDR memaddr, unsigned char *myaddr, int len)
{
if (len < 16 || using_tcp || using_pc)
return write_small (memaddr, myaddr, len);
/* Read LEN bytes from inferior memory at MEMADDR. Put the result
at debugger address MYADDR. Returns length moved.
- Small transactions we send
- m <addr>;l
- and receive
- 00000000 12345678 ?
+ Small transactions we send
+ and receive
+ 00000000 12345678 ?
*/
static int
-e7000_read_inferior_memory (memaddr, myaddr, len)
- CORE_ADDR memaddr;
- unsigned char *myaddr;
- int len;
+e7000_read_inferior_memory (CORE_ADDR memaddr, unsigned char *myaddr, int len)
{
int count;
int c;
char buf[200];
/* Starting address of this pass. */
-/* printf("READ INF %x %x %d\n", memaddr, myaddr, len);*/
+/* printf("READ INF %x %x %d\n", memaddr, myaddr, len); */
if (((memaddr - 1) + len) < memaddr)
{
errno = EIO;
return 0;
}
- sprintf (buf, "m %x;l\r", memaddr);
+ sprintf (buf, "m %s;l\r", paddr_nz (memaddr));
puts_e7000debug (buf);
- for (count = 0; count < len; count += 4)
+ for (count = 0; count < len; count += 4)
{
/* Suck away the address */
- c = gch ();
+ c = gch ();
while (c != ' ')
- c = gch ();
+ c = gch ();
c = gch ();
- if (c == '*')
+ if (c == '*')
{ /* Some kind of error */
- puts_e7000debug (".\r"); /* Some errors leave us in memory input mode */
- expect_full_prompt();
+ puts_e7000debug (".\r"); /* Some errors leave us in memory input mode */
+ expect_full_prompt ();
return -1;
}
while (c != ' ')
- c = gch ();
+ c = gch ();
/* Now read in the data */
- for (i = 0; i < 4; i++)
+ for (i = 0; i < 4; i++)
{
- int b = gbyte();
- if (count + i < len) {
- myaddr[count + i] = b;
- }
+ int b = gbyte ();
+ if (count + i < len)
+ {
+ myaddr[count + i] = b;
+ }
}
/* Skip the trailing ? and send a . to end and a cr for more */
- gch ();
+ gch ();
gch ();
if (count + 4 >= len)
- puts_e7000debug(".\r");
+ puts_e7000debug (".\r");
else
- puts_e7000debug("\r");
+ puts_e7000debug ("\r");
}
- expect_prompt();
+ expect_prompt ();
return len;
}
/*
- For large transfers we used to send
+ For large transfers we used to send
- d <addr> <endaddr>\r
- and receive
+ and receive
<ADDRESS> < D A T A > < ASCII CODE >
00000000 5F FD FD FF DF 7F DF FF 01 00 01 00 02 00 08 04 "_..............."
00000010 FF D7 FF 7F D7 F1 7F FF 00 05 00 00 08 00 40 00 "..............@."
00000020 7F FD FF F7 7F FF FF F7 00 00 00 00 00 00 00 00 "................"
- A cost in chars for each transaction of 80 + 5*n-bytes.
+ A cost in chars for each transaction of 80 + 5*n-bytes.
- Large transactions could be done with the srecord load code, but
- there is a pause for a second before dumping starts, which slows the
- average rate down!
-*/
+ Large transactions could be done with the srecord load code, but
+ there is a pause for a second before dumping starts, which slows the
+ average rate down!
+ */
static int
-e7000_read_inferior_memory_large (memaddr, myaddr, len)
- CORE_ADDR memaddr;
- unsigned char *myaddr;
- int len;
+e7000_read_inferior_memory_large (CORE_ADDR memaddr, unsigned char *myaddr,
+ int len)
{
int count;
int c;
return 0;
}
- sprintf (buf, "d %x %x\r", memaddr, memaddr + len - 1);
+ sprintf (buf, "d %s %s\r", paddr_nz (memaddr), paddr_nz (memaddr + len - 1));
puts_e7000debug (buf);
count = 0;
c = gch ();
-
+
/* skip down to the first ">" */
- while( c != '>' )
+ while (c != '>')
c = gch ();
/* now skip to the end of that line */
- while( c != '\r' )
+ while (c != '\r')
c = gch ();
c = gch ();
}
}
/* throw out the rest of the line */
- while( c != '\r' )
+ while (c != '\r')
c = gch ();
}
#if 0
static int
-fast_but_for_the_pause_e7000_read_inferior_memory (memaddr, myaddr, len)
- CORE_ADDR memaddr;
- char *myaddr;
- int len;
+fast_but_for_the_pause_e7000_read_inferior_memory (CORE_ADDR memaddr,
+ char *myaddr, int len)
{
int loop;
int c;
if (c != ENQ)
{
/* Got an error */
- error ("Memory read error");
+ error (_("Memory read error"));
}
putchar_e7000 (ACK);
expect ("SV s");
#endif
+/* Transfer LEN bytes between GDB address MYADDR and target address
+ MEMADDR. If WRITE is non-zero, transfer them to the target,
+ otherwise transfer them from the target. TARGET is unused.
+
+ Returns the number of bytes transferred. */
+
static int
-e7000_xfer_inferior_memory (memaddr, myaddr, len, write, target)
- CORE_ADDR memaddr;
- unsigned char *myaddr;
- int len;
- int write;
- struct target_ops *target; /* ignored */
+e7000_xfer_inferior_memory (CORE_ADDR memaddr, gdb_byte *myaddr, int len,
+ int write, struct mem_attrib *attrib,
+ struct target_ops *target)
{
if (write)
- return e7000_write_inferior_memory( memaddr, myaddr, len);
- else
- if( len < 16 )
- return e7000_read_inferior_memory( memaddr, myaddr, len);
- else
- return e7000_read_inferior_memory_large( memaddr, myaddr, len);
+ return e7000_write_inferior_memory (memaddr, myaddr, len);
+ else if (len < 16)
+ return e7000_read_inferior_memory (memaddr, myaddr, len);
+ else
+ return e7000_read_inferior_memory_large (memaddr, myaddr, len);
}
static void
-e7000_kill (args, from_tty)
- char *args;
- int from_tty;
+e7000_kill (void)
{
}
static void
-e7000_load (args, from_tty)
- char *args;
- int from_tty;
+e7000_load (char *args, int from_tty)
{
struct cleanup *old_chain;
asection *section;
bfd *pbfd;
bfd_vma entry;
#define WRITESIZE 0x1000
- char buf[2 + 4 + 4 + WRITESIZE]; /* `DT' + <addr> + <len> + <data> */
+ char buf[2 + 4 + 4 + WRITESIZE];
/* `DT' + <addr> + <len> + <data> */
char *filename;
int quiet;
int nostart;
time_t start_time, end_time; /* Start and end times of download */
unsigned long data_count; /* Number of bytes transferred to memory */
- int oldtimeout = timeout;
+ int oldtimeout = timeout;
timeout = remote_timeout;
{
char *arg;
- while (isspace (*args)) args++;
+ while (isspace (*args))
+ args++;
arg = args;
- while ((*args != '\000') && !isspace (*args)) args++;
+ while ((*args != '\000') && !isspace (*args))
+ args++;
if (*args != '\000')
*args++ = '\000';
else if (strncmp (arg, "-nostart", strlen (arg)) == 0)
nostart = 1;
else
- error ("unknown option `%s'", arg);
+ error (_("unknown option `%s'"), arg);
}
if (!filename)
perror_with_name (filename);
return;
}
- old_chain = make_cleanup ((make_cleanup_func) bfd_close, pbfd);
+ old_chain = make_cleanup_bfd_close (pbfd);
- if (!bfd_check_format (pbfd, bfd_object))
- error ("\"%s\" is not an object file: %s", filename,
+ if (!bfd_check_format (pbfd, bfd_object))
+ error (_("\"%s\" is not an object file: %s"), filename,
bfd_errmsg (bfd_get_error ()));
start_time = time (NULL);
expect ("\nOK");
- for (section = pbfd->sections; section; section = section->next)
+ for (section = pbfd->sections; section; section = section->next)
{
if (bfd_get_section_flags (pbfd, section) & SEC_LOAD)
{
file_ptr fptr;
section_address = bfd_get_section_vma (pbfd, section);
- section_size = bfd_get_section_size_before_reloc (section);
+ section_size = bfd_get_section_size (section);
if (!quiet)
- printf_filtered ("[Loading section %s at 0x%x (%d bytes)]\n",
+ printf_filtered ("[Loading section %s at 0x%s (%s bytes)]\n",
bfd_get_section_name (pbfd, section),
- section_address,
- section_size);
+ paddr_nz (section_address),
+ paddr_u (section_size));
fptr = 0;
-
+
data_count += section_size;
while (section_size > 0)
bfd_get_section_contents (pbfd, section, buf + 10, fptr, count);
- if (SERIAL_WRITE (e7000_desc, buf, count + 10))
+ if (serial_write (e7000_desc, buf, count + 10))
fprintf_unfiltered (gdb_stderr,
- "e7000_load: SERIAL_WRITE failed: %s\n",
- safe_strerror(errno));
+ "e7000_load: serial_write failed: %s\n",
+ safe_strerror (errno));
expect ("OK");
if (exec_bfd)
write_pc (bfd_get_start_address (exec_bfd));
- inferior_pid = 0; /* No process now */
+ inferior_ptid = null_ptid; /* No process now */
/* This is necessary because many things were based on the PC at the time that
we attached to the monitor, which is no longer valid now that we have loaded
entry = bfd_get_start_address (pbfd);
if (!quiet)
- printf_unfiltered ("[Starting %s at 0x%x]\n", filename, entry);
+ printf_unfiltered ("[Starting %s at 0x%s]\n", filename, paddr_nz (entry));
-/* start_routine (entry);*/
+/* start_routine (entry); */
}
report_transfer_performance (data_count, start_time, end_time);
instructions. */
static void
-e7000_mourn_inferior ()
+e7000_mourn_inferior (void)
{
remove_breakpoints ();
unpush_target (&e7000_ops);
/* Since we can change to soft breakpoints dynamically, we must define
more than enough. Was breakaddr[MAX_E7000DEBUG_BREAKPOINTS]. */
-static CORE_ADDR breakaddr[MAX_BREAKPOINTS] = {0};
+static CORE_ADDR breakaddr[MAX_BREAKPOINTS] =
+{0};
static int
-e7000_insert_breakpoint (addr, shadow)
- CORE_ADDR addr;
- unsigned char *shadow;
+e7000_insert_breakpoint (struct bp_target_info *bp_tgt)
{
+ CORE_ADDR addr = bp_tgt->placed_address;
int i;
char buf[200];
#if 0
breakaddr[i] = addr;
/* Save old contents, and insert a nop in the space */
#ifdef HARD_BREAKPOINTS
- if (BC_BREAKPOINTS)
+ if (BC_BREAKPOINTS)
{
- sprintf (buf, "BC%d A=%x\r", i+1, addr);
+ sprintf (buf, "BC%d A=%s\r", i + 1, paddr_nz (addr));
puts_e7000debug (buf);
}
- else
+ else
{
- sprintf (buf, "B %x\r", addr);
+ sprintf (buf, "B %s\r", paddr_nz (addr));
puts_e7000debug (buf);
}
#else
#if 0
- e7000_read_inferior_memory (addr, shadow, 2);
+ bp_tgt->shadow_len = 2;
+ e7000_read_inferior_memory (addr, bp_tgt->shadow_contents, 2);
e7000_write_inferior_memory (addr, nop, 2);
#endif
return 0;
}
- error ("Too many breakpoints ( > %d) for the E7000\n",
+ error (_("Too many breakpoints ( > %d) for the E7000."),
MAX_E7000DEBUG_BREAKPOINTS);
return 1;
}
static int
-e7000_remove_breakpoint (addr, shadow)
- CORE_ADDR addr;
- unsigned char *shadow;
+e7000_remove_breakpoint (struct bp_target_info *bp_tgt)
{
+ CORE_ADDR addr = bp_tgt->placed_address;
int i;
char buf[200];
{
breakaddr[i] = 0;
#ifdef HARD_BREAKPOINTS
- if (BC_BREAKPOINTS)
+ if (BC_BREAKPOINTS)
{
- sprintf (buf, "BC%d - \r", i+1);
+ sprintf (buf, "BC%d - \r", i + 1);
puts_e7000debug (buf);
}
- else
+ else
{
- sprintf (buf, "B - %x\r", addr);
+ sprintf (buf, "B - %s\r", paddr_nz (addr));
puts_e7000debug (buf);
}
expect_prompt ();
#else
- sprintf (buf, "B - %x\r", addr);
+ sprintf (buf, "B - %s\r", paddr_nz (addr));
puts_e7000debug (buf);
expect_prompt ();
#if 0
/* Replace the insn under the break */
- e7000_write_inferior_memory (addr, shadow, 2);
+ e7000_write_inferior_memory (addr, bp_tgt->shadow_contents,
+ bp_tgt->shadow_len);
#endif
#endif
return 0;
}
-
- warning ("Can't find breakpoint associated with 0x%x\n", addr);
+
+ warning (_("Can't find breakpoint associated with 0x%s."), paddr_nz (addr));
return 1;
}
is placed on the users terminal until the prompt is seen. */
static void
-e7000_command (args, fromtty)
- char *args;
- int fromtty;
+e7000_command (char *args, int fromtty)
{
/* FIXME: arbitrary limit on length of args. */
char buf[200];
echo = 0;
if (!e7000_desc)
- error ("e7000 target not open.");
+ error (_("e7000 target not open."));
if (!args)
{
puts_e7000debug ("\r");
static void
-e7000_drain_command (args, fromtty)
- char *args;
- int fromtty;
-
+e7000_drain_command (char *args, int fromtty)
{
int c;
- puts_e7000debug("end\r");
+ puts_e7000debug ("end\r");
putchar_e7000 (CTRLC);
- while ((c = readchar (1) != -1))
+ while ((c = readchar (1)) != -1)
{
if (quit_flag)
{
- putchar_e7000(CTRLC);
+ putchar_e7000 (CTRLC);
quit_flag = 0;
}
if (c > ' ' && c < 127)
#define NITEMS 7
static int
-why_stop ()
+why_stop (void)
{
- static char *strings[NITEMS] = {
+ static char *strings[NITEMS] =
+ {
"STEP NORMAL",
"BREAK POINT",
"BREAK KEY",
for (i = 0; i < NITEMS; ++i)
p[i] = strings[i];
-
+
c = gch ();
while (1)
{
for (i = 0; i < NITEMS; i++)
{
- if (c == *(p[i]))
+ if (c == *(p[i]))
{
p[i]++;
- if (*(p[i]) == 0)
- {
+ if (*(p[i]) == 0)
+ {
/* found one of the choices */
return i;
}
/* Suck characters, if a string match, then return the strings index
otherwise echo them. */
-int
-expect_n (strings)
-char **strings;
+static int
+expect_n (char **strings)
{
char *(ptr[10]);
- int n;
+ int n;
int c;
char saveaway[100];
char *buffer = saveaway;
/* Count number of expect strings */
- for (n = 0; strings[n]; n++)
+ for (n = 0; strings[n]; n++)
{
ptr[n] = strings[n];
}
#ifdef __GO32__
if (kbhit ())
{
- int k = getkey();
+ int k = getkey ();
if (k == 1)
quit_flag = 1;
for (i = 0; i < n; i++)
{
- if (c == ptr[i][0])
+ if (c == ptr[i][0])
{
ptr[i]++;
if (ptr[i][0] == 0)
ptr[i] = strings[i];
}
}
-
+
if (gotone)
{
/* Save it up incase we find that there was no match */
- *buffer ++ = c;
+ *buffer++ = c;
}
else
{
- if (buffer != saveaway)
+ if (buffer != saveaway)
{
*buffer++ = 0;
printf_unfiltered ("%s", buffer);
pc, and the simulators never do. */
static void
-sub2_from_pc ()
+sub2_from_pc (void)
{
char buf[4];
char buf2[200];
store_signed_integer (buf,
- REGISTER_RAW_SIZE(PC_REGNUM),
- read_register (PC_REGNUM) -2);
- supply_register (PC_REGNUM, buf);
- sprintf (buf2, ".PC %x\r", read_register (PC_REGNUM));
+ register_size (current_gdbarch, PC_REGNUM),
+ read_register (PC_REGNUM) - 2);
+ regcache_raw_supply (current_regcache, PC_REGNUM, buf);
+ sprintf (buf2, ".PC %s\r", phex_nz (read_register (PC_REGNUM), 0));
puts_e7000debug (buf2);
}
#define WAS_RUNNING 2
#define WAS_OTHER 3
-static char *estrings[] = {
+static char *estrings[] =
+{
"** SLEEP",
"BREAK !",
"** PC",
/* Wait until the remote machine stops, then return, storing status in
STATUS just as `wait' would. */
-static int
-e7000_wait (pid, status)
- int pid;
- struct target_waitstatus *status;
+static ptid_t
+e7000_wait (ptid_t ptid, struct target_waitstatus *status)
{
int stop_reason;
int regno;
int running_count = 0;
int had_sleep = 0;
int loop = 1;
- char *wanted_nopc;
+ char *wanted_nopc = NULL;
+ int realregs = 0;
/* Then echo chars until PC= string seen */
gch (); /* Drop cr */
while (loop)
{
switch (expect_n (estrings))
- {
+ {
case WAS_OTHER:
/* how did this happen ? */
loop = 0;
/* Skip till the PC= */
expect ("=");
-#ifdef GDB_TARGET_IS_SH
- wanted_nopc = want_nopc;
if (TARGET_ARCHITECTURE->arch == bfd_arch_sh)
- switch (TARGET_ARCHITECTURE->mach)
- {
- case bfd_mach_sh3:
- case bfd_mach_sh3e:
- case bfd_mach_sh4:
- wanted_nopc = want_sh3_nopc;
- }
-#else
- if (h8300smode)
- wanted_nopc = want_nopc_h8300s;
- else
- wanted_nopc = want_nopc_h8300h;
-#endif
+ {
+ wanted_nopc = want_nopc_sh;
+ realregs = 59;
+ switch (TARGET_ARCHITECTURE->mach)
+ {
+ case bfd_mach_sh3:
+ case bfd_mach_sh3e:
+ case bfd_mach_sh4:
+ wanted_nopc = want_nopc_sh3;
+ }
+ }
+ if (TARGET_ARCHITECTURE->arch == bfd_arch_h8300)
+ {
+ wanted_nopc = want_nopc_h8300h;
+ realregs = 10;
+ switch (TARGET_ARCHITECTURE->mach)
+ {
+ case bfd_mach_h8300s:
+ case bfd_mach_h8300sn:
+ case bfd_mach_h8300sx:
+ case bfd_mach_h8300sxn:
+ wanted_nopc = want_nopc_h8300s;
+ realregs = 11;
+ }
+ }
fetch_regs_from_dump (gch, wanted_nopc);
/* And supply the extra ones the simulator uses */
- for (regno = NUM_REALREGS; regno < NUM_REGS; regno++)
+ for (regno = realregs; regno < NUM_REGS; regno++)
{
int buf = 0;
- supply_register (regno, (char *) &buf);
+ regcache_raw_supply (current_regcache, regno, (char *) &buf);
}
stop_reason = why_stop ();
switch (stop_reason)
{
case 1: /* Breakpoint */
- write_pc (read_pc ()); /* PC is always off by 2 for breakpoints */
- status->value.sig = TARGET_SIGNAL_TRAP;
+ write_pc (read_pc ()); /* PC is always off by 2 for breakpoints */
+ status->value.sig = TARGET_SIGNAL_TRAP;
break;
case 0: /* Single step */
- status->value.sig = TARGET_SIGNAL_TRAP;
+ status->value.sig = TARGET_SIGNAL_TRAP;
break;
case 2: /* Interrupt */
if (had_sleep)
{
- status->value.sig = TARGET_SIGNAL_TRAP;
+ status->value.sig = TARGET_SIGNAL_TRAP;
sub2_from_pc ();
}
else
{
- status->value.sig = TARGET_SIGNAL_INT;
+ status->value.sig = TARGET_SIGNAL_INT;
}
break;
case 3:
break;
case 4:
printf_unfiltered ("a cycle address error?\n");
- status->value.sig = TARGET_SIGNAL_UNKNOWN;
+ status->value.sig = TARGET_SIGNAL_UNKNOWN;
break;
case 5:
- status->value.sig = TARGET_SIGNAL_ILL;
+ status->value.sig = TARGET_SIGNAL_ILL;
break;
case 6:
- status->value.sig = TARGET_SIGNAL_SEGV;
+ status->value.sig = TARGET_SIGNAL_SEGV;
break;
case 7: /* Anything else (NITEMS + 1) */
printf_unfiltered ("a write protect error?\n");
- status->value.sig = TARGET_SIGNAL_UNKNOWN;
+ status->value.sig = TARGET_SIGNAL_UNKNOWN;
break;
default:
/* Get the user's attention - this should never happen. */
- abort ();
+ internal_error (__FILE__, __LINE__, _("failed internal consistency check"));
}
- return 0;
+ return inferior_ptid;
}
/* Stop the running program. */
static void
-e7000_stop ()
+e7000_stop (void)
{
/* Sending a ^C is supposed to stop the running program. */
putchar_e7000 (CTRLC);
/* Define the target subroutine names. */
-struct target_ops e7000_ops ;
-static void init_e7000_ops(void)
+struct target_ops e7000_ops;
+
+static void
+init_e7000_ops (void)
{
- e7000_ops.to_shortname = "e7000";
- e7000_ops.to_longname = "Remote Hitachi e7000 target";
- e7000_ops.to_doc = "Use a remote Hitachi e7000 ICE connected by a serial line;\n\
+ e7000_ops.to_shortname = "e7000";
+ e7000_ops.to_longname = "Remote Renesas e7000 target";
+ e7000_ops.to_doc = "Use a remote Renesas e7000 ICE connected by a serial line;\n\
or a network connection.\n\
Arguments are the name of the device for the serial line,\n\
the speed to connect at in bits per second.\n\
eg\n\
target e7000 /dev/ttya 9600\n\
-target e7000 foobar" ;
- e7000_ops.to_open = e7000_open;
- e7000_ops.to_close = e7000_close;
- e7000_ops.to_attach = 0;
- e7000_ops.to_detach = e7000_detach;
- e7000_ops.to_resume = e7000_resume;
- e7000_ops.to_wait = e7000_wait;
- e7000_ops.to_fetch_registers = e7000_fetch_register;
- e7000_ops.to_store_registers = e7000_store_register;
- e7000_ops.to_prepare_to_store = e7000_prepare_to_store;
- e7000_ops.to_xfer_memory = e7000_xfer_inferior_memory;
- e7000_ops.to_files_info = e7000_files_info;
- e7000_ops.to_insert_breakpoint = e7000_insert_breakpoint;
- e7000_ops.to_remove_breakpoint = e7000_remove_breakpoint;
- e7000_ops.to_terminal_init = 0;
- e7000_ops.to_terminal_inferior = 0;
- e7000_ops.to_terminal_ours_for_output = 0;
- e7000_ops.to_terminal_ours = 0;
- e7000_ops.to_terminal_info = 0;
- e7000_ops.to_kill = e7000_kill;
- e7000_ops.to_load = e7000_load;
- e7000_ops.to_lookup_symbol = 0;
- e7000_ops.to_create_inferior = e7000_create_inferior;
- e7000_ops.to_mourn_inferior = e7000_mourn_inferior;
- e7000_ops.to_can_run = 0;
- e7000_ops.to_notice_signals = 0;
- e7000_ops.to_thread_alive = 0;
- e7000_ops.to_stop = e7000_stop;
- e7000_ops.to_stratum = process_stratum;
- e7000_ops.DONT_USE = 0;
- e7000_ops.to_has_all_memory = 1;
- e7000_ops.to_has_memory = 1;
- e7000_ops.to_has_stack = 1;
- e7000_ops.to_has_registers = 1;
- e7000_ops.to_has_execution = 1;
- e7000_ops.to_sections = 0;
- e7000_ops.to_sections_end = 0;
- e7000_ops.to_magic = OPS_MAGIC;
+target e7000 foobar";
+ e7000_ops.to_open = e7000_open;
+ e7000_ops.to_close = e7000_close;
+ e7000_ops.to_detach = e7000_detach;
+ e7000_ops.to_resume = e7000_resume;
+ e7000_ops.to_wait = e7000_wait;
+ e7000_ops.to_fetch_registers = e7000_fetch_register;
+ e7000_ops.to_store_registers = e7000_store_register;
+ e7000_ops.to_prepare_to_store = e7000_prepare_to_store;
+ e7000_ops.deprecated_xfer_memory = e7000_xfer_inferior_memory;
+ e7000_ops.to_files_info = e7000_files_info;
+ e7000_ops.to_insert_breakpoint = e7000_insert_breakpoint;
+ e7000_ops.to_remove_breakpoint = e7000_remove_breakpoint;
+ e7000_ops.to_kill = e7000_kill;
+ e7000_ops.to_load = e7000_load;
+ e7000_ops.to_create_inferior = e7000_create_inferior;
+ e7000_ops.to_mourn_inferior = e7000_mourn_inferior;
+ e7000_ops.to_stop = e7000_stop;
+ e7000_ops.to_stratum = process_stratum;
+ e7000_ops.to_has_all_memory = 1;
+ e7000_ops.to_has_memory = 1;
+ e7000_ops.to_has_stack = 1;
+ e7000_ops.to_has_registers = 1;
+ e7000_ops.to_has_execution = 1;
+ e7000_ops.to_magic = OPS_MAGIC;
};
+extern initialize_file_ftype _initialize_remote_e7000; /* -Wmissing-prototypes */
+
void
-_initialize_remote_e7000 ()
+_initialize_remote_e7000 (void)
{
- init_e7000_ops() ;
+ init_e7000_ops ();
add_target (&e7000_ops);
add_com ("e7000", class_obscure, e7000_command,
- "Send a command to the e7000 monitor.");
+ _("Send a command to the e7000 monitor."));
add_com ("ftplogin", class_obscure, e7000_login_command,
- "Login to machine and change to directory.");
+ _("Login to machine and change to directory."));
add_com ("ftpload", class_obscure, e7000_ftp_command,
- "Fetch and load a file from previously described place.");
+ _("Fetch and load a file from previously described place."));
add_com ("drain", class_obscure, e7000_drain_command,
- "Drain pending e7000 text buffers.");
-
- add_show_from_set (add_set_cmd ("usehardbreakpoints", no_class,
- var_integer, (char *)&use_hard_breakpoints,
- "Set use of hardware breakpoints for all breakpoints.\n", &setlist),
- &showlist);
+ _("Drain pending e7000 text buffers."));
+
+ add_setshow_integer_cmd ("usehardbreakpoints", no_class,
+ &use_hard_breakpoints, _("\
+Set use of hardware breakpoints for all breakpoints."), _("\
+Show use of hardware breakpoints for all breakpoints."), NULL,
+ NULL,
+ NULL, /* FIXME: i18n: */
+ &setlist, &showlist);
}
projects / deliverable / binutils-gdb.git / blobdiff