/* Remote target communications for serial-line targets in custom GDB protocol
- Copyright 1988, 1991, 1992, 1993, 1994 Free Software Foundation, Inc.
+ Copyright 1988, 1991, 1992, 1993, 1994, 1995, 1996 Free Software Foundation, Inc.
This file is part of GDB.
You should have received a copy of the GNU General Public License
along with this program; if not, write to the Free Software
-Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. */
+Foundation, Inc., 59 Temple Place - Suite 330, Boston, MA 02111-1307, USA. */
/* Remote communication protocol.
- - if CSUM is incorrect
<data> is as follows:
- All values are encoded in ascii hex digits.
+ Most values are encoded in ascii hex digits. Signal numbers are according
+ to the numbering in target.h.
Request Packet
+ set thread Hct... Set thread for subsequent operations.
+ c = 'c' for thread used in step and
+ continue; t... can be -1 for all
+ threads.
+ c = 'g' for thread used in other
+ operations. If zero, pick a thread,
+ any thread.
+ reply OK for success
+ ENN for an error.
+
read registers g
reply XX....X Each byte of register data
is described by two hex digits.
where only part of the data was
written).
- cont cAA..AA AA..AA is address to resume
+ continue cAA..AA AA..AA is address to resume
If AA..AA is omitted,
resume at same address.
If AA..AA is omitted,
resume at same address.
+ continue with Csig;AA Continue with signal sig (hex signal
+ signal number).
+
+ step with Ssig;AA Like 'C' but step not continue.
+ signal
+
last signal ? Reply the current reason for stopping.
This is the same reply as is generated
for step or cont : SAA where AA is the
signal number.
+ detach D Reply OK.
+
There is no immediate reply to step or cont.
The reply comes when the machine stops.
- It is SAA AA is the "signal number"
+ It is SAA AA is the signal number.
- or... TAAn...:r...;n:r...;n...:r...;
+ or... TAAn...:r...;n...:r...;n...:r...;
AA = signal number
- n... = register number
- r... = register contents
+ n... = register number (hex)
+ r... = register contents
+ n... = `thread'
+ r... = thread process ID. This is
+ a hex integer.
+ n... = other string not starting
+ with valid hex digit.
+ gdb should ignore this n,r pair
+ and go on to the next. This way
+ we can extend the protocol.
or... WAA The process exited, and AA is
the exit status. This is only
applicable for certains sorts of
targets.
+ or... XAA The process terminated with signal
+ AA.
+ or... OXX..XX XX..XX is hex encoding of ASCII data. This
+ can happen at any time while the program is
+ running and the debugger should
+ continue to wait for 'W', 'T', etc.
+
+ thread alive TXX Find out if the thread XX is alive.
+ reply OK thread is still alive
+ ENN thread is dead
+
+ remote restart RXX Restart the remote server
+
+ extended ops ! Use the extended remote protocol.
+ Sticky -- only needs to be set once.
+
kill request k
toggle debug d toggle debug flag (see 386 & 68k stubs)
general set QXXXX=yyyy Set value of XXXX to yyyy.
query sect offs qOffsets Get section offsets. Reply is
Text=xxx;Data=yyy;Bss=zzz
- console output Otext Send text to stdout. Only comes from
- remote target.
Responses can be run-length encoded to save space. A '*' means that
the next character is an ASCII encoding giving a repeat count which
"0* " means the same as "0000". */
#include "defs.h"
-#include <string.h>
+#include "gdb_string.h"
#include <fcntl.h>
#include "frame.h"
#include "inferior.h"
#include "symfile.h"
#include "target.h"
#include "wait.h"
-#include "terminal.h"
+/*#include "terminal.h"*/
#include "gdbcmd.h"
#include "objfiles.h"
#include "gdb-stabs.h"
+#include "gdbthread.h"
#include "dcache.h"
/* Prototypes for local functions */
-static int
-remote_write_bytes PARAMS ((CORE_ADDR memaddr, unsigned char *myaddr, int len));
+static int remote_write_bytes PARAMS ((CORE_ADDR memaddr,
+ char *myaddr, int len));
-static int
-remote_read_bytes PARAMS ((CORE_ADDR memaddr, unsigned char *myaddr, int len));
+static int remote_read_bytes PARAMS ((CORE_ADDR memaddr,
+ char *myaddr, int len));
-static void
-remote_files_info PARAMS ((struct target_ops *ignore));
+static void remote_files_info PARAMS ((struct target_ops *ignore));
-static int
-remote_xfer_memory PARAMS ((CORE_ADDR memaddr, char *myaddr, int len,
- int should_write, struct target_ops *target));
+static int remote_xfer_memory PARAMS ((CORE_ADDR memaddr, char *myaddr,
+ int len, int should_write,
+ struct target_ops *target));
-static void
-remote_prepare_to_store PARAMS ((void));
+static void remote_prepare_to_store PARAMS ((void));
-static void
-remote_fetch_registers PARAMS ((int regno));
+static void remote_fetch_registers PARAMS ((int regno));
-static void
-remote_resume PARAMS ((int pid, int step, enum target_signal siggnal));
+static void remote_resume PARAMS ((int pid, int step,
+ enum target_signal siggnal));
-static int
-remote_start_remote PARAMS ((char *dummy));
+static int remote_start_remote PARAMS ((char *dummy));
-static void
-remote_open PARAMS ((char *name, int from_tty));
+static void remote_open PARAMS ((char *name, int from_tty));
-static void
-remote_close PARAMS ((int quitting));
+static void extended_remote_open PARAMS ((char *name, int from_tty));
-static void
-remote_store_registers PARAMS ((int regno));
+static void remote_open_1 PARAMS ((char *, int, struct target_ops *));
-static void
-getpkt PARAMS ((char *buf, int forever));
+static void remote_close PARAMS ((int quitting));
-static void
-putpkt PARAMS ((char *buf));
+static void remote_store_registers PARAMS ((int regno));
-static void
-remote_send PARAMS ((char *buf));
+static void remote_mourn PARAMS ((void));
-static int
-readchar PARAMS ((int timeout));
+static void extended_remote_restart PARAMS ((void));
+
+static void extended_remote_mourn PARAMS ((void));
+
+static void extended_remote_create_inferior PARAMS ((char *, char *, char **));
+
+static void remote_mourn_1 PARAMS ((struct target_ops *));
+
+static void getpkt PARAMS ((char *buf, int forever));
+
+static int putpkt PARAMS ((char *buf));
+
+static void remote_send PARAMS ((char *buf));
+
+static int readchar PARAMS ((int timeout));
static int remote_wait PARAMS ((int pid, struct target_waitstatus *status));
-static int
-tohex PARAMS ((int nib));
+static void remote_kill PARAMS ((void));
-static int
-fromhex PARAMS ((int a));
+static int tohex PARAMS ((int nib));
-static void
-remote_detach PARAMS ((char *args, int from_tty));
+static int fromhex PARAMS ((int a));
-static void
-remote_interrupt PARAMS ((int signo));
+static void remote_detach PARAMS ((char *args, int from_tty));
-static void
-remote_interrupt_twice PARAMS ((int signo));
+static void remote_interrupt PARAMS ((int signo));
-static void
-interrupt_query PARAMS ((void));
+static void remote_interrupt_twice PARAMS ((int signo));
+
+static void interrupt_query PARAMS ((void));
+
+static void set_thread PARAMS ((int, int));
+
+static int remote_thread_alive PARAMS ((int));
+
+static void get_offsets PARAMS ((void));
+
+static int read_frame PARAMS ((char *));
+
+static int remote_insert_breakpoint PARAMS ((CORE_ADDR, char *));
+
+static int remote_remove_breakpoint PARAMS ((CORE_ADDR, char *));
extern struct target_ops remote_ops; /* Forward decl */
+extern struct target_ops extended_remote_ops; /* Forward decl */
/* This was 5 seconds, which is a long time to sit and wait.
Unless this is going though some terminal server or multiplexer or
other form of hairy serial connection, I would think 2 seconds would
be plenty. */
-static int remote_timeout = 2;
-#if 0
-int icache;
-#endif
+/* Changed to allow option to set timeout value.
+ was static int remote_timeout = 2; */
+extern int remote_timeout;
+
+/* This variable chooses whether to send a ^C or a break when the user
+ requests program interruption. Although ^C is usually what remote
+ systems expect, and that is the default here, sometimes a break is
+ preferable instead. */
+
+static int remote_break;
/* Descriptor for I/O to remote machine. Initialize it to NULL so that
remote_open knows that we don't have a file open when the program
#define PBUFSIZ (REGISTER_BYTES * 2 + 32)
#endif
+/* This variable sets the number of bytes to be written to the target
+ in a single packet. Normally PBUFSIZ is satisfactory, but some
+ targets need smaller values (perhaps because the receiving end
+ is slow). */
+
+static int remote_write_size = PBUFSIZ;
+
/* Should we try the 'P' request? If this is set to one when the stub
doesn't support 'P', the only consequence is some unnecessary traffic. */
static int stub_supports_P = 1;
+\f
+/* These are the threads which we last sent to the remote system. -1 for all
+ or -2 for not sent yet. */
+int general_thread;
+int cont_thread;
+
+static void
+set_thread (th, gen)
+ int th;
+ int gen;
+{
+ char buf[PBUFSIZ];
+ int state = gen ? general_thread : cont_thread;
+ if (state == th)
+ return;
+ buf[0] = 'H';
+ buf[1] = gen ? 'g' : 'c';
+ if (th == 42000)
+ {
+ buf[2] = '0';
+ buf[3] = '\0';
+ }
+ else if (th < 0)
+ sprintf (&buf[2], "-%x", -th);
+ else
+ sprintf (&buf[2], "%x", th);
+ putpkt (buf);
+ getpkt (buf, 0);
+ if (gen)
+ general_thread = th;
+ else
+ cont_thread = th;
+}
+\f
+/* Return nonzero if the thread TH is still alive on the remote system. */
+
+static int
+remote_thread_alive (th)
+ int th;
+{
+ char buf[PBUFSIZ];
+
+ buf[0] = 'T';
+ if (th < 0)
+ sprintf (&buf[1], "-%x", -th);
+ else
+ sprintf (&buf[1], "%x", th);
+ putpkt (buf);
+ getpkt (buf, 0);
+ return (buf[0] == 'O' && buf[1] == 'K');
+}
+
+/* Restart the remote side; this is an extended protocol operation. */
+
+static void
+extended_remote_restart ()
+{
+ char buf[PBUFSIZ];
+
+ /* Send the restart command; for reasons I don't understand the
+ remote side really expects a number after the "R". */
+ buf[0] = 'R';
+ sprintf (&buf[1], "%x", 0);
+ putpkt (buf);
+
+ /* Now query for status so this looks just like we restarted
+ gdbserver from scratch. */
+ putpkt ("?");
+ getpkt (buf, 0);
+}
\f
/* Clean up connection to a remote debugger. */
+ symfile_objfile->num_sections
* sizeof (offs->offsets));
- /* FIXME: This code assumes gdb-stabs.h is being used; it's broken
- for xcoff, dwarf, sdb-coff, etc. But there is no simple
- canonical representation for this stuff. (Just what does "text"
- as seen by the stub mean, anyway? I think it means all sections
- with SEC_CODE set, but we currently have no way to deal with that). */
-
ANOFFSET (offs, SECT_OFF_TEXT) = text_addr;
/* This is a temporary kludge to force data and bss to use the same offsets
immediate_quit = 1; /* Allow user to interrupt it */
/* Ack any packet which the remote side has already sent. */
-
SERIAL_WRITE (remote_desc, "+", 1);
+ /* Let the stub know that we want it to return the thread. */
+ set_thread (-1, 0);
+
get_offsets (); /* Get text, data & bss offsets */
putpkt ("?"); /* initiate a query from remote machine */
immediate_quit = 0;
start_remote (); /* Initialize gdb process mechanisms */
-
return 1;
}
/* Open a connection to a remote debugger.
NAME is the filename used for communication. */
+static void
+remote_open (name, from_tty)
+ char *name;
+ int from_tty;
+{
+ remote_open_1 (name, from_tty, &remote_ops);
+}
+
+/* Open a connection to a remote debugger using the extended
+ remote gdb protocol. NAME is the filename used for communication. */
+
+static void
+extended_remote_open (name, from_tty)
+ char *name;
+ int from_tty;
+{
+ char buf[PBUFSIZ];
+
+ /* Do the basic remote open stuff. */
+ remote_open_1 (name, from_tty, &extended_remote_ops);
+
+ /* Now tell the remote that we're using the extended protocol. */
+ putpkt ("!");
+ getpkt (buf, 0);
+
+}
+
+/* Generic code for opening a connection to a remote target. */
static DCACHE *remote_dcache;
static void
-remote_open (name, from_tty)
+remote_open_1 (name, from_tty, target)
char *name;
int from_tty;
+ struct target_ops *target;
{
if (name == 0)
- error (
-"To open a remote debug connection, you need to specify what serial\n\
+ error ("To open a remote debug connection, you need to specify what serial\n\
device is attached to the remote system (e.g. /dev/ttya).");
target_preopen (from_tty);
- unpush_target (&remote_ops);
+ unpush_target (target);
remote_dcache = dcache_init (remote_read_bytes, remote_write_bytes);
}
}
+
SERIAL_RAW (remote_desc);
/* If there is something sitting in the buffer we might take it as a
puts_filtered (name);
puts_filtered ("\n");
}
- push_target (&remote_ops); /* Switch to using remote target now */
+ push_target (target); /* Switch to using remote target now */
/* Start out by trying the 'P' request to set registers. We set this each
time that we open a new target so that if the user switches from one
stub to another, we can (if the target is closed and reopened) cope. */
stub_supports_P = 1;
+ general_thread = -2;
+ cont_thread = -2;
+
/* Without this, some commands which require an active target (such as kill)
won't work. This variable serves (at least) double duty as both the pid
of the target process (if it has such), and as a flag indicating that a
several processes. */
inferior_pid = 42000;
-
/* Start the remote connection; if error (0), discard this target.
In particular, if the user quits, be sure to discard it
(we'd be in an inconsistent state otherwise). */
if (!catch_errors (remote_start_remote, (char *)0,
- "Couldn't establish connection to remote target\n", RETURN_MASK_ALL))
+ "Couldn't establish connection to remote target\n", RETURN_MASK_ALL))
pop_target();
}
-/* remote_detach()
- takes a program previously attached to and detaches it.
- We better not have left any breakpoints
- in the program or it'll die when it hits one.
- Close the open connection to the remote debugger.
- Use this when you want to detach and do something else
- with your gdb. */
+/* This takes a program previously attached to and detaches it. After
+ this is done, GDB can be used to debug some other program. We
+ better not have left any breakpoints in the target program or it'll
+ die when it hits one. */
static void
remote_detach (args, from_tty)
char *args;
int from_tty;
{
+ char buf[PBUFSIZ];
+
if (args)
error ("Argument given to \"detach\" when remotely debugging.");
-
+
+ /* Tell the remote target to detach. */
+ strcpy (buf, "D");
+ remote_send (buf);
+
pop_target ();
if (from_tty)
puts_filtered ("Ending remote debugging.\n");
return a - '0';
else if (a >= 'a' && a <= 'f')
return a - 'a' + 10;
- else
+ else
error ("Reply contains invalid hex digit %d", a);
}
\f
/* Tell the remote machine to resume. */
+static enum target_signal last_sent_signal = TARGET_SIGNAL_0;
+int last_sent_step;
+
static void
remote_resume (pid, step, siggnal)
int pid, step;
{
char buf[PBUFSIZ];
- if (siggnal)
- {
- target_terminal_ours_for_output ();
- printf_filtered
- ("Can't send signals to a remote system. %s not sent.\n",
- target_signal_to_name (siggnal));
- target_terminal_inferior ();
- }
+ if (pid == -1)
+ set_thread (inferior_pid, 0);
+ else
+ set_thread (pid, 0);
dcache_flush (remote_dcache);
- strcpy (buf, step ? "s": "c");
+ last_sent_signal = siggnal;
+ last_sent_step = step;
+
+ if (siggnal != TARGET_SIGNAL_0)
+ {
+ buf[0] = step ? 'S' : 'C';
+ buf[1] = tohex (((int)siggnal >> 4) & 0xf);
+ buf[2] = tohex ((int)siggnal & 0xf);
+ buf[3] = '\0';
+ }
+ else
+ strcpy (buf, step ? "s": "c");
putpkt (buf);
}
if (remote_debug)
printf_unfiltered ("remote_interrupt called\n");
- SERIAL_WRITE (remote_desc, "\003", 1); /* Send a ^C */
+ /* Send a break or a ^C, depending on user preference. */
+ if (remote_break)
+ SERIAL_SEND_BREAK (remote_desc);
+ else
+ SERIAL_WRITE (remote_desc, "\003", 1);
}
static void (*ofunc)();
target_terminal_inferior ();
}
+/* If nonzero, ignore the next kill. */
+int kill_kludge;
+
/* Wait until the remote machine stops, then return,
storing status in STATUS just as `wait' would.
Returns "pid" (though it's not clear what, if anything, that
struct target_waitstatus *status;
{
unsigned char buf[PBUFSIZ];
+ int thread_num = -1;
status->kind = TARGET_WAITKIND_EXITED;
status->value.integer = 0;
while (*p)
{
unsigned char *p1;
+ char *p_temp;
- regno = strtol (p, &p1, 16); /* Read the register number */
+ regno = strtol ((const char *) p, &p_temp, 16); /* Read the register number */
+ p1 = (unsigned char *)p_temp;
if (p1 == p)
- warning ("Remote sent badly formed register number: %s\nPacket: '%s'\n",
- p1, buf);
-
- p = p1;
-
- if (*p++ != ':')
- warning ("Malformed packet (missing colon): %s\nPacket: '%s'\n",
- p, buf);
-
- if (regno >= NUM_REGS)
- warning ("Remote sent bad register number %d: %s\nPacket: '%s'\n",
- regno, p, buf);
-
- for (i = 0; i < REGISTER_RAW_SIZE (regno); i++)
{
- if (p[0] == 0 || p[1] == 0)
- warning ("Remote reply is too short: %s", buf);
- regs[i] = fromhex (p[0]) * 16 + fromhex (p[1]);
- p += 2;
+ p1 = (unsigned char *) strchr ((const char *) p, ':');
+ if (p1 == NULL)
+ warning ("Malformed packet (missing colon): %s\n\
+Packet: '%s'\n",
+ p, buf);
+ if (strncmp ((const char *) p, "thread", p1 - p) == 0)
+ {
+ thread_num = strtol ((const char *) ++p1, &p_temp, 16);
+ p = (unsigned char *)p_temp;
+ }
+ }
+ else
+ {
+ p = p1;
+
+ if (*p++ != ':')
+ warning ("Malformed packet (missing colon): %s\n\
+Packet: '%s'\n",
+ p, buf);
+
+ if (regno >= NUM_REGS)
+ warning ("Remote sent bad register number %ld: %s\n\
+Packet: '%s'\n",
+ regno, p, buf);
+
+ for (i = 0; i < REGISTER_RAW_SIZE (regno); i++)
+ {
+ if (p[0] == 0 || p[1] == 0)
+ warning ("Remote reply is too short: %s", buf);
+ regs[i] = fromhex (p[0]) * 16 + fromhex (p[1]);
+ p += 2;
+ }
+ supply_register (regno, regs);
}
if (*p++ != ';')
warning ("Remote register badly formatted: %s", buf);
-
- supply_register (regno, regs);
}
}
/* fall through */
status->value.sig = (enum target_signal)
(((fromhex (buf[1])) << 4) + (fromhex (buf[2])));
- return inferior_pid;
+ goto got_status;
case 'W': /* Target exited */
{
/* The remote process exited. */
status->kind = TARGET_WAITKIND_EXITED;
status->value.integer = (fromhex (buf[1]) << 4) + fromhex (buf[2]);
- return inferior_pid;
+ goto got_status;
}
+ case 'X':
+ status->kind = TARGET_WAITKIND_SIGNALLED;
+ status->value.sig = (enum target_signal)
+ (((fromhex (buf[1])) << 4) + (fromhex (buf[2])));
+ kill_kludge = 1;
+
+ goto got_status;
case 'O': /* Console output */
- fputs_filtered ((char *)(buf + 1), gdb_stdout);
+ for (p = buf + 1; *p; p +=2)
+ {
+ char tb[2];
+ char c = fromhex (p[0]) * 16 + fromhex (p[1]);
+ tb[0] = c;
+ tb[1] = 0;
+ if (target_output_hook)
+ target_output_hook (tb);
+ else
+ fputs_filtered (tb, gdb_stdout);
+ }
continue;
+ case '\0':
+ if (last_sent_signal != TARGET_SIGNAL_0)
+ {
+ /* Zero length reply means that we tried 'S' or 'C' and
+ the remote system doesn't support it. */
+ target_terminal_ours_for_output ();
+ printf_filtered
+ ("Can't send signals to this remote system. %s not sent.\n",
+ target_signal_to_name (last_sent_signal));
+ last_sent_signal = TARGET_SIGNAL_0;
+ target_terminal_inferior ();
+
+ strcpy ((char *) buf, last_sent_step ? "s" : "c");
+ putpkt ((char *) buf);
+ continue;
+ }
+ /* else fallthrough */
default:
warning ("Invalid remote reply: %s", buf);
continue;
}
}
+ got_status:
+ if (thread_num != -1)
+ {
+ /* Initial thread value can only be acquired via wait, so deal with
+ this marker which is used before the first thread value is
+ acquired. */
+ if (inferior_pid == 42000)
+ {
+ inferior_pid = thread_num;
+ add_thread (inferior_pid);
+ }
+ return thread_num;
+ }
+ return inferior_pid;
}
/* Number of bytes of registers this stub implements. */
char *p;
char regs[REGISTER_BYTES];
+ set_thread (inferior_pid, 1);
+
sprintf (buf, "g");
remote_send (buf);
int i;
char *p;
+ set_thread (inferior_pid, 1);
+
if (regno >= 0 && stub_supports_P)
{
/* Try storing a single register. */
remote_send (buf);
}
-#if 0
-
-/* Use of the data cache is disabled because it loses for looking at
+/*
+ Use of the data cache *used* to be disabled because it loses for looking at
and changing hardware I/O ports and the like. Accepting `volatile'
- would perhaps be one way to fix it, but a better way which would
- win for more cases would be to use the executable file for the text
- segment, like the `icache' code below but done cleanly (in some
- target-independent place, perhaps in target_xfer_memory, perhaps
- based on assigning each target a speed or perhaps by some simpler
- mechanism). */
+ would perhaps be one way to fix it. Another idea would be to use the
+ executable file for the text segment (for all SEC_CODE sections?
+ For all SEC_READONLY sections?). This has problems if you want to
+ actually see what the memory contains (e.g. self-modifying code,
+ clobbered memory, user downloaded the wrong thing).
+
+ Because it speeds so much up, it's now enabled, if you're playing
+ with registers you turn it of (set remotecache 0)
+*/
/* Read a word from remote address ADDR and return it.
This goes through the data cache. */
+#if 0 /* unused? */
static int
remote_fetch_word (addr)
CORE_ADDR addr;
{
-#if 0
- if (icache)
- {
- extern CORE_ADDR text_start, text_end;
-
- if (addr >= text_start && addr < text_end)
- {
- int buffer;
- xfer_core_file (addr, &buffer, sizeof (int));
- return buffer;
- }
- }
-#endif
return dcache_fetch (remote_dcache, addr);
}
{
dcache_poke (remote_dcache, addr, word);
}
-#endif /* 0 */
+#endif /* 0 (unused?) */
+
\f
/* Write memory data directly to the remote machine.
This does not inform the data cache; the data cache uses this.
static int
remote_write_bytes (memaddr, myaddr, len)
CORE_ADDR memaddr;
- unsigned char *myaddr;
+ char *myaddr;
int len;
{
char buf[PBUFSIZ];
int i;
char *p;
+ int done;
+ /* Chop the transfer down if necessary */
- /* FIXME-32x64: Need a version of print_address_numeric which puts the
- result in a buffer like sprintf. */
- sprintf (buf, "M%lx,%x:", (unsigned long) memaddr, len);
+ done = 0;
+ while (done < len)
+ {
+ int todo = len - done;
+ int cando = min(remote_write_size, PBUFSIZ) / 2 - 32; /* num bytes that will fit */
- /* We send target system values byte by byte, in increasing byte addresses,
- each byte encoded as two hex characters. */
+ if (todo > cando)
+ todo = cando;
- p = buf + strlen (buf);
- for (i = 0; i < len; i++)
- {
- *p++ = tohex ((myaddr[i] >> 4) & 0xf);
- *p++ = tohex (myaddr[i] & 0xf);
- }
- *p = '\0';
+ /* FIXME-32x64: Need a version of print_address_numeric which puts the
+ result in a buffer like sprintf. */
+ sprintf (buf, "M%lx,%x:", (unsigned long) memaddr + done, todo);
- putpkt (buf);
- getpkt (buf, 0);
+ /* We send target system values byte by byte, in increasing byte addresses,
+ each byte encoded as two hex characters. */
- if (buf[0] == 'E')
- {
- /* There is no correspondance between what the remote protocol uses
- for errors and errno codes. We would like a cleaner way of
- representing errors (big enough to include errno codes, bfd_error
- codes, and others). But for now just return EIO. */
- errno = EIO;
- return 0;
+ p = buf + strlen (buf);
+ for (i = 0; i < todo; i++)
+ {
+ *p++ = tohex ((myaddr[i + done] >> 4) & 0xf);
+ *p++ = tohex (myaddr[i + done] & 0xf);
+ }
+ *p = '\0';
+
+ putpkt (buf);
+ getpkt (buf, 0);
+
+ if (buf[0] == 'E')
+ {
+ /* There is no correspondance between what the remote protocol uses
+ for errors and errno codes. We would like a cleaner way of
+ representing errors (big enough to include errno codes, bfd_error
+ codes, and others). But for now just return EIO. */
+ errno = EIO;
+ return 0;
+ }
+ done += todo;
}
return len;
}
static int
remote_read_bytes (memaddr, myaddr, len)
CORE_ADDR memaddr;
- unsigned char *myaddr;
+ char *myaddr;
int len;
{
char buf[PBUFSIZ];
int i;
char *p;
+ int done;
+ /* Chop transfer down if neccessary */
+#if 0
+ /* FIXME: This is wrong for larger packets */
if (len > PBUFSIZ / 2 - 1)
abort ();
-
- /* FIXME-32x64: Need a version of print_address_numeric which puts the
- result in a buffer like sprintf. */
- sprintf (buf, "m%lx,%x", (unsigned long) memaddr, len);
- putpkt (buf);
- getpkt (buf, 0);
-
- if (buf[0] == 'E')
+#endif
+ done = 0;
+ while (done < len)
{
- /* There is no correspondance between what the remote protocol uses
- for errors and errno codes. We would like a cleaner way of
- representing errors (big enough to include errno codes, bfd_error
- codes, and others). But for now just return EIO. */
- errno = EIO;
- return 0;
- }
+ int todo = len - done;
+ int cando = PBUFSIZ / 2 - 32; /* number of bytes that will fit. */
+ if (todo > cando)
+ todo = cando;
+
+ /* FIXME-32x64: Need a version of print_address_numeric which puts the
+ result in a buffer like sprintf. */
+ sprintf (buf, "m%lx,%x", (unsigned long) memaddr + done, todo);
+ putpkt (buf);
+ getpkt (buf, 0);
+
+ if (buf[0] == 'E')
+ {
+ /* There is no correspondance between what the remote protocol uses
+ for errors and errno codes. We would like a cleaner way of
+ representing errors (big enough to include errno codes, bfd_error
+ codes, and others). But for now just return EIO. */
+ errno = EIO;
+ return 0;
+ }
/* Reply describes memory byte by byte,
each byte encoded as two hex characters. */
- p = buf;
- for (i = 0; i < len; i++)
- {
- if (p[0] == 0 || p[1] == 0)
- /* Reply is short. This means that we were able to read only part
- of what we wanted to. */
- break;
- myaddr[i] = fromhex (p[0]) * 16 + fromhex (p[1]);
- p += 2;
+ p = buf;
+ for (i = 0; i < todo; i++)
+ {
+ if (p[0] == 0 || p[1] == 0)
+ /* Reply is short. This means that we were able to read only part
+ of what we wanted to. */
+ return i + done;
+ myaddr[i + done] = fromhex (p[0]) * 16 + fromhex (p[1]);
+ p += 2;
+ }
+ done += todo;
}
- return i;
+ return len;
}
\f
/* Read or write LEN bytes from inferior memory at MEMADDR, transferring
int should_write;
struct target_ops *target; /* ignored */
{
- int xfersize;
- int bytes_xferred;
- int total_xferred = 0;
-
- while (len > 0)
- {
- if (len > MAXBUFBYTES)
- xfersize = MAXBUFBYTES;
- else
- xfersize = len;
-
- if (should_write)
- bytes_xferred = remote_write_bytes (memaddr,
- (unsigned char *)myaddr, xfersize);
- else
- bytes_xferred = remote_read_bytes (memaddr,
- (unsigned char *)myaddr, xfersize);
-
- /* If we get an error, we are done xferring. */
- if (bytes_xferred == 0)
- break;
-
- memaddr += bytes_xferred;
- myaddr += bytes_xferred;
- len -= bytes_xferred;
- total_xferred += bytes_xferred;
- }
- return total_xferred;
+ return dcache_xfer_memory (remote_dcache, memaddr, myaddr, len, should_write);
}
+
#if 0
/* Enable after 4.12. */
remote_send (buf)
char *buf;
{
-
putpkt (buf);
getpkt (buf, 0);
/* Send a packet to the remote machine, with error checking.
The data of the packet is in BUF. */
-static void
+static int
putpkt (buf)
char *buf;
{
char buf2[PBUFSIZ];
int cnt = strlen (buf);
int ch;
+ int tcount = 0;
char *p;
/* Copy the packet into buffer BUF2, encapsulating it
and giving it a checksum. */
- if (cnt > sizeof(buf2) - 5) /* Prosanity check */
+ if (cnt > (int) sizeof (buf2) - 5) /* Prosanity check */
abort();
p = buf2;
{
ch = readchar (remote_timeout);
- if (remote_debug)
+ if (remote_debug)
{
switch (ch)
{
case '$':
if (started_error_output)
{
- putc_unfiltered ('\n');
+ putchar_unfiltered ('\n');
started_error_output = 0;
}
}
case '+':
if (remote_debug)
printf_unfiltered("Ack\n");
- return;
+ return 1;
case SERIAL_TIMEOUT:
+ tcount ++;
+ if (tcount > 3)
+ return 0;
break; /* Retransmit buffer */
case '$':
{
started_error_output = 1;
printf_unfiltered ("putpkt: Junk: ");
}
- putc_unfiltered (ch & 0177);
+ putchar_unfiltered (ch & 0177);
}
continue;
}
char *buf;
int forever;
{
- char *bp;
int c;
int tries;
int timeout;
int val;
+ strcpy (buf,"timeout");
+
if (forever)
- timeout = -1;
+ {
+#ifdef MAINTENANCE_CMDS
+ timeout = watchdog > 0 ? watchdog : -1;
+#else
+ timeout = -1;
+#endif
+ }
+
else
timeout = remote_timeout;
-#define MAX_TRIES 10
+#define MAX_TRIES 3
for (tries = 1; tries <= MAX_TRIES; tries++)
{
if (c == SERIAL_TIMEOUT)
{
+#ifdef MAINTENANCE_CMDS
+ if (forever) /* Watchdog went off. Kill the target. */
+ {
+ target_mourn_inferior ();
+ error ("Watchdog has expired. Target detached.\n");
+ }
+#endif
if (remote_debug)
puts_filtered ("Timed out.\n");
goto retry;
}
/* Try the whole thing again. */
-retry:
+ retry:
SERIAL_WRITE (remote_desc, "-", 1);
}
static void
remote_kill ()
{
- putpkt ("k");
+ /* For some mysterious reason, wait_for_inferior calls kill instead of
+ mourn after it gets TARGET_WAITKIND_SIGNALLED. Work around it. */
+ if (kill_kludge)
+ {
+ kill_kludge = 0;
+ target_mourn_inferior ();
+ return;
+ }
+
+ /* Use catch_errors so the user can quit from gdb even when we aren't on
+ speaking terms with the remote system. */
+ catch_errors (putpkt, "k", "", RETURN_MASK_ERROR);
+
/* Don't wait for it to die. I'm not really sure it matters whether
we do or not. For the existing stubs, kill is a noop. */
target_mourn_inferior ();
static void
remote_mourn ()
{
- unpush_target (&remote_ops);
+ remote_mourn_1 (&remote_ops);
+}
+
+static void
+extended_remote_mourn ()
+{
+ /* We do _not_ want to mourn the target like this; this will
+ remove the extended remote target from the target stack,
+ and the next time the user says "run" it'll fail.
+
+ FIXME: What is the right thing to do here? */
+#if 0
+ remote_mourn_1 (&extended_remote_ops);
+#endif
+}
+
+/* Worker function for remote_mourn. */
+static void
+remote_mourn_1 (target)
+ struct target_ops *target;
+{
+ unpush_target (target);
generic_mourn_inferior ();
}
-\f
-#ifdef REMOTE_BREAKPOINT
+/* In the extended protocol we want to be able to do things like
+ "run" and have them basically work as expected. So we need
+ a special create_inferior function.
+
+ FIXME: One day add support for changing the exec file
+ we're debugging, arguments and an environment. */
+
+static void
+extended_remote_create_inferior (exec_file, args, env)
+ char *exec_file;
+ char *args;
+ char **env;
+{
+ /* Rip out the breakpoints; we'll reinsert them after restarting
+ the remote server. */
+ remove_breakpoints ();
+
+ /* Now restart the remote server. */
+ extended_remote_restart ();
+
+ /* Now put the breakpoints back in. This way we're safe if the
+ restart function works via a unix fork on the remote side. */
+ insert_breakpoints ();
+
+ /* Clean up from the last time we were running. */
+ clear_proceed_status ();
+
+ /* Let the remote process run. */
+ proceed (-1, TARGET_SIGNAL_0, 0);
+}
+
+\f
/* On some machines, e.g. 68k, we may use a different breakpoint instruction
- than other targets. */
-static unsigned char break_insn[] = REMOTE_BREAKPOINT;
+ than other targets; in those use REMOTE_BREAKPOINT instead of just
+ BREAKPOINT. Also, bi-endian targets may define LITTLE_REMOTE_BREAKPOINT
+ and BIG_REMOTE_BREAKPOINT. If none of these are defined, we just call
+ the standard routines that are in mem-break.c. */
+
+/* FIXME, these ought to be done in a more dynamic fashion. For instance,
+ the choice of breakpoint instruction affects target program design and
+ vice versa, and by making it user-tweakable, the special code here
+ goes away and we need fewer special GDB configurations. */
+
+#if defined (LITTLE_REMOTE_BREAKPOINT) && defined (BIG_REMOTE_BREAKPOINT) && !defined(REMOTE_BREAKPOINT)
+#define REMOTE_BREAKPOINT
+#endif
-/* Check that it fits in BREAKPOINT_MAX bytes. */
-static unsigned char check_break_insn_size[BREAKPOINT_MAX] = REMOTE_BREAKPOINT;
+#ifdef REMOTE_BREAKPOINT
-#else /* No REMOTE_BREAKPOINT. */
+/* If the target isn't bi-endian, just pretend it is. */
+#if !defined (LITTLE_REMOTE_BREAKPOINT) && !defined (BIG_REMOTE_BREAKPOINT)
+#define LITTLE_REMOTE_BREAKPOINT REMOTE_BREAKPOINT
+#define BIG_REMOTE_BREAKPOINT REMOTE_BREAKPOINT
+#endif
-/* Same old breakpoint instruction. This code does nothing different
- than mem-break.c. */
-static unsigned char break_insn[] = BREAKPOINT;
+static unsigned char big_break_insn[] = BIG_REMOTE_BREAKPOINT;
+static unsigned char little_break_insn[] = LITTLE_REMOTE_BREAKPOINT;
-#endif /* No REMOTE_BREAKPOINT. */
+#endif /* REMOTE_BREAKPOINT */
/* Insert a breakpoint on targets that don't have any better breakpoint
support. We read the contents of the target location and stash it,
CORE_ADDR addr;
char *contents_cache;
{
+#ifdef REMOTE_BREAKPOINT
int val;
- val = target_read_memory (addr, contents_cache, sizeof break_insn);
+ val = target_read_memory (addr, contents_cache, sizeof big_break_insn);
if (val == 0)
- val = target_write_memory (addr, (char *)break_insn, sizeof break_insn);
+ {
+ if (TARGET_BYTE_ORDER == BIG_ENDIAN)
+ val = target_write_memory (addr, (char *) big_break_insn,
+ sizeof big_break_insn);
+ else
+ val = target_write_memory (addr, (char *) little_break_insn,
+ sizeof little_break_insn);
+ }
return val;
+#else
+ return memory_insert_breakpoint (addr, contents_cache);
+#endif /* REMOTE_BREAKPOINT */
}
static int
CORE_ADDR addr;
char *contents_cache;
{
- return target_write_memory (addr, contents_cache, sizeof break_insn);
+#ifdef REMOTE_BREAKPOINT
+ return target_write_memory (addr, contents_cache, sizeof big_break_insn);
+#else
+ return memory_remove_breakpoint (addr, contents_cache);
+#endif /* REMOTE_BREAKPOINT */
}
\f
/* Define the target subroutine names */
remote_prepare_to_store, /* to_prepare_to_store */
remote_xfer_memory, /* to_xfer_memory */
remote_files_info, /* to_files_info */
-
remote_insert_breakpoint, /* to_insert_breakpoint */
remote_remove_breakpoint, /* to_remove_breakpoint */
-
NULL, /* to_terminal_init */
NULL, /* to_terminal_inferior */
NULL, /* to_terminal_ours_for_output */
remote_mourn, /* to_mourn_inferior */
0, /* to_can_run */
0, /* to_notice_signals */
+ remote_thread_alive, /* to_thread_alive */
+ 0, /* to_stop */
+ process_stratum, /* to_stratum */
+ NULL, /* to_next */
+ 1, /* to_has_all_memory */
+ 1, /* to_has_memory */
+ 1, /* to_has_stack */
+ 1, /* to_has_registers */
+ 1, /* to_has_execution */
+ NULL, /* sections */
+ NULL, /* sections_end */
+ OPS_MAGIC /* to_magic */
+};
+
+struct target_ops extended_remote_ops = {
+ "extended-remote", /* to_shortname */
+ "Extended remote serial target in gdb-specific protocol",/* to_longname */
+ "Use a remote computer via a serial line, using a gdb-specific protocol.\n\
+Specify the serial device it is connected to (e.g. /dev/ttya).", /* to_doc */
+ extended_remote_open, /* to_open */
+ remote_close, /* to_close */
+ NULL, /* to_attach */
+ remote_detach, /* to_detach */
+ remote_resume, /* to_resume */
+ remote_wait, /* to_wait */
+ remote_fetch_registers, /* to_fetch_registers */
+ remote_store_registers, /* to_store_registers */
+ remote_prepare_to_store, /* to_prepare_to_store */
+ remote_xfer_memory, /* to_xfer_memory */
+ remote_files_info, /* to_files_info */
+
+ remote_insert_breakpoint, /* to_insert_breakpoint */
+ remote_remove_breakpoint, /* to_remove_breakpoint */
+
+ NULL, /* to_terminal_init */
+ NULL, /* to_terminal_inferior */
+ NULL, /* to_terminal_ours_for_output */
+ NULL, /* to_terminal_ours */
+ NULL, /* to_terminal_info */
+ remote_kill, /* to_kill */
+ generic_load, /* to_load */
+ NULL, /* to_lookup_symbol */
+ extended_remote_create_inferior,/* to_create_inferior */
+ extended_remote_mourn, /* to_mourn_inferior */
+ 0, /* to_can_run */
+ 0, /* to_notice_signals */
+ remote_thread_alive, /* to_thread_alive */
0, /* to_stop */
process_stratum, /* to_stratum */
NULL, /* to_next */
_initialize_remote ()
{
add_target (&remote_ops);
+ add_target (&extended_remote_ops);
+
+ add_show_from_set (add_set_cmd ("remotetimeout", no_class,
+ var_integer, (char *)&remote_timeout,
+ "Set timeout value for remote read.\n", &setlist),
+ &showlist);
+
+ add_show_from_set (add_set_cmd ("remotebreak", no_class,
+ var_integer, (char *)&remote_break,
+ "Set whether to send break if interrupted.\n", &setlist),
+ &showlist);
+
+ add_show_from_set (add_set_cmd ("remotewritesize", no_class,
+ var_integer, (char *)&remote_write_size,
+ "Set the maximum number of bytes in each memory write packet.\n", &setlist),
+ &showlist);
}
projects / deliverable / binutils-gdb.git / blobdiff