Olof Johansson [Tue, 11 Jun 2013 05:13:52 +0000 (22:13 -0700)] 
Merge tag 'renesas-dt-for-v3.11' of git://git./linux/kernel/git/horms/renesas into next/dt
From Simon Horman:
Renesas ARM-based SoC DT updates for v3.11
* Armadillo800eva reference DT - bring up armadillo800eva baord
using DT as much as possible
* Remove unused GIC dtsi entries for r8a7790 and r8a73a4
* Add AS3711 and CPUFreq DT bindings for kzm9g-reference
* Add irqpin DT support for marzen-reference
* tag 'renesas-dt-for-v3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: marzen-reference: add irqpin support in DT
ARM: shmobile: kzm9g-reference: add AS3711 and CPUFreq DT bindings
ARM: shmobile: armadillo800eva: Reference DT implementation
ARM: shmobile: Remove unused r8a7790 GIC CPU interface DT bits
ARM: shmobile: Remove unused r8a73a4 GIC CPU interface DT bits
ARM: shmobile: r8a7740: Prepare for reference DT setup
ARM: shmobile: r8a7740: Add OF support to initialze the GIC
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Tue, 11 Jun 2013 04:39:37 +0000 (21:39 -0700)]
Merge tag 'dt-3.11-4' of git://git.infradead.org/users/jcooper/linux into next/dt
From Jason Cooper:
mvebu dt changes for v3.11 (round 4)
- kirkwood
- reshuffle nodes from kirkwood.dtsi to -6281.dtsi, etc
- add i2c-gpio for km_kirkwood
- add cpu node so pending cpufreq driver will init
* tag 'dt-3.11-4' of git://git.infradead.org/users/jcooper/linux:
ARM: Kirkwood add cpus definition needed by cpufreq driver to dtsi
ARM: kirkwood: add i2c-gpio controller for km_kirkwood
ARM: kirkwood: refactor dtsi to largest common nodes
Signed-off-by: Olof Johansson <olof@lixom.net>
Arnd Bergmann [Mon, 10 Jun 2013 14:48:36 +0000 (16:48 +0200)] 
ARM: dts: add missing cpu #address-cell values
A recent series has added CPU numbers to a lot of dts files,
but unfortunately in a few cases the #address-cells
and #size-cells values are missing, which causes build warnings.
This adds the missing ones for sunxi and sama5 that I found
through build testing.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Olof Johansson [Sat, 8 Jun 2013 00:51:39 +0000 (17:51 -0700)]
Merge tag 'vt8500/dts-3.11' of git://github.com/linux-wmt/linux-vtwm into next/dt
From Tony Prisk, vt8500 devicetree updates for 3.11.
* tag 'vt8500/dts-3.11' of git://github.com/linux-wmt/linux-vtwm:
dts: vt8500: Correct reference clock on WM8850 SoCs
dts: vt8500: Add ARM, AHB, APB and DDR clock nodes to SoC files
dts: vt8500: Populate missing PLL nodes
dts: clk: vt8500: Update SoC dtsi to use WM8850 PLL clocks
dts: vt8500: Update serial nodes and disable by default in SoC files
dts: vt8500: Add devicetree support for WM8750 SoC and APC8750 board
dts: vt8500: Fix invalid/missing cpu nodes for soc files.
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Fri, 7 Jun 2013 23:38:54 +0000 (16:38 -0700)]
Merge branch 'dts-cpus-updates' of git://linux-arm.org/linux-2.6-lp into next/dt
From Lorenzo Pieralisi, this is a series of patches that cleans up the CPU
nodes in most of the SoC dtsi files to conform to the standard bindings.
* 'dts-cpus-updates' of git://linux-arm.org/linux-2.6-lp:
ARM: dts: sunxi: cpus/cpu nodes dts updates
ARM: dts: spear: cpus/cpu nodes dts updates
ARM: dts: sh7372: cpus/cpu nodes dts updates
ARM: dts: r8a7740: cpus/cpu nodes dts updates
ARM: dts: pxa2xx: cpus/cpu nodes dts updates
ARM: dts: prima2: cpus/cpu node dts updates
ARM: dts: picoxcell: cpus/cpu nodes dts updates
ARM: dts: omap: cpus/cpu nodes dts updates
ARM: dts: lpc32xx: cpus/cpu nodes dts updates
ARM: dts: imx: cpus/cpu nodes dts updates
ARM: dts: exynos5440: cpus/cpu nodes dts updates
ARM: dts: at91: cpus/cpu node dts updates
ARM: dts: armada-370-xp: cpus/cpu node dts updates
ARM: dts: am33xx: cpus/cpu nodes dts updates
Signed-off-by: Olof Johansson <olof@lixom.net>
Guennadi Liakhovetski [Wed, 3 Apr 2013 09:19:07 +0000 (11:19 +0200)] 
ARM: shmobile: marzen-reference: add irqpin support in DT
Add an irqpin interrupt controller DT node on marzen-reference.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Guennadi Liakhovetski [Fri, 5 Apr 2013 10:00:37 +0000 (12:00 +0200)]
ARM: shmobile: kzm9g-reference: add AS3711 and CPUFreq DT bindings
This adds DT bindings for an AS3711 PMIC, used for supplying power to the
CPU, some peripherals and the backlight, as well as extends the cpu0 DT
node with OPPs and a reference to the PMIC to support the CPUFreq and
CPU DVFS functions.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Bastian Hecht [Wed, 17 Apr 2013 10:34:06 +0000 (12:34 +0200)] 
ARM: shmobile: armadillo800eva: Reference DT implementation
Provide alternate board code for the Armadillo800EVA to demonstrate how
DT may be used given the current state of driver device tree support.
This is intended to act as a reference for mach-shmobile developers.
This a rather bare bone version with the following devices supported:
- GIC
- irqpins
- i2c0/1
- touchscreen
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Thu, 16 May 2013 06:05:16 +0000 (15:05 +0900)] 
ARM: shmobile: Remove unused r8a7790 GIC CPU interface DT bits
Remove unused GIC CPU interface DT bits for r8a7790.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Magnus Damm [Thu, 16 May 2013 06:03:55 +0000 (15:03 +0900)]
ARM: shmobile: Remove unused r8a73a4 GIC CPU interface DT bits
Remove unused GIC CPU interface DT bits for r8a73a4.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Bastian Hecht [Wed, 17 Apr 2013 10:34:05 +0000 (12:34 +0200)]
ARM: shmobile: r8a7740: Prepare for reference DT setup
We need three steps to prepare for the new Armadillo reference DT board code:
- Split the device list into r8a7740_early_devices used by the old platform
data setup (board-armadillo.c) and r8a7740_devices_dt used by both
setup variants.
- Introduce new r8a7740_init_delay() to be more flexible about calling
shmobile_setup_delay().
- For the generic r8a7740 support, we switch to device tree setup for
the GIC, the irqpin devices and the I2C controllers.
This is slightly similar to commit
3b00f9342623a5ebc
"ARM: shmobile: sh73a0: Do not use early devices with DT reference"
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Bastian Hecht [Wed, 17 Apr 2013 10:34:04 +0000 (12:34 +0200)]
ARM: shmobile: r8a7740: Add OF support to initialze the GIC
We add a variant to initalize the interrupt controller in case we describe
the GIC using the Device Tree and not platform data.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Tony Prisk [Fri, 17 May 2013 09:30:05 +0000 (21:30 +1200)] 
dts: vt8500: Correct reference clock on WM8850 SoCs
WM8850 SoCs use a 24Mhz reference clock for the PLLs but the SoC file
currently parents all PLLs to the 25Mhz reference clock.
This patch corrects the PLL parent clock references.
Signed-off-by: Tony Prisk <linux@prisktech.co.nz>
Adam Baker [Sun, 2 Jun 2013 21:59:50 +0000 (22:59 +0100)] 
ARM: Kirkwood add cpus definition needed by cpufreq driver to dtsi
The Kirkwood CPU Freq driver needs a CPU definition in order for the probe
routine to activate it. Add a suitable definition to kirkwood.dtsi
This definition is only correct for single core SoCs. There is a dual core
SoC in the kirkwood family (88F632X) but the rest of the Kirkwood drivers in
the kernel don't currently support it. If they ever do the cpus definition
would need to be duplicated in each of the SoC specific include files.
Signed-off-by: Adam Baker <linux@baker-net.org.uk>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Olof Johansson [Sat, 1 Jun 2013 07:38:04 +0000 (00:38 -0700)]
Merge tag 'at91-dt' of git://github.com/at91linux/linux-at91 into next/dt
From Nicolas Ferre:
Big DT-centric update for AT91:
- Calao boards update, removal of one board C file and
associated defconfig, Kconfig Makefile lines
- several Acme boards updates
- addition of watchdog, uart and pinctrl descriptions for
several products
- modification of RTC compatible string for 9x5 family
* tag 'at91-dt' of git://github.com/at91linux/linux-at91: (21 commits)
ARM: at91/dt: add pinctrl definition for at91 tc blocks
ARM: at91/dts: add the watchdog nodes for at91 boards
ARM: at91/dtsi: add the watchdog nodes for at91 SoC
ARM: at91: drop non DT: Calao USB-A96x
ARM: at91: dt: add Calao USB-A9G20 low power version
ARM: at91: dt: usb-a9263: add dataflash support
ARM: at91: dt: usb-a9263: update shutdown controller
ARM: at91: dt: usb-a9260: update shutdown controller
ARM: at91: dt: sam9260: add i2c gpio pinctrl
ARM: at91: switch Fox G20 board .dts to pre-processor defines
ARM: at91: add Acme Systems Fox G20 board
ARM: at91/at91-ariag25.dts: UART0/1 nodes are disabled
ARM: at91/at91sam9x5.dtsi: add UART0/1 nodes
ARM: at91/at91-ariag25.dts: add RTC node
ARM: at91: at91sam9x5 RTC is not compatible with at91rm9200 one
ARM: at91: udpate defconfigs
ARM: at91: dt: switch to standard IRQ flag defines
ARM: at91: dt: switch to pinctrl to pre-processor
ARM: at91: dt: add pinctrl pre-processor define
ARM: at91: dt: switch to standard GPIO flag defines.
...
Signed-off-by: Olof Johansson <olof@lixom.net>
Arnd Bergmann [Fri, 31 May 2013 15:49:28 +0000 (17:49 +0200)]
ARM: nomadik: fix clocksource warning
The clocksource API has changed slightly, which causes a harmless
warning:
/git/arm-soc/drivers/clocksource/nomadik-mtu.c:259:28: warning: 'nmdk_timer_match' defined but not used [-Wunused-variable]
static struct of_device_id nmdk_timer_match[] __initconst = {
^
Fortunately, the same API change also lets us simplify the code
while removing the warning.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
Olof Johansson [Sat, 1 Jun 2013 05:47:53 +0000 (22:47 -0700)]
Merge tag 'dt-3.11-3' of git://git.infradead.org/users/jcooper/linux into next/dt
From jason Cooper, mvebu dt changes for v3.11.
Signed-off-by: Olof Johansson <olof@lixom.net>
* tag 'dt-3.11-3' of git://git.infradead.org/users/jcooper/linux: (27 commits)
arm: kirkwood: openblocks-a6: add support for Init button
arm: kirkwood: openblocks-a6: group pinmux configurations
arm: kirkwood: ts219: move pinmux configs to the right devices
arm: kirkwood: topkick: move pinmux configs to the right devices
arm: kirkwood: openblocks_a6: move pinmux configs to the right devices
arm: kirkwood: nsa310: move pinmux configs to the right devices
arm: kirkwood: readynas: move pinmux configs to the right devices
arm: kirkwood: mplcec4: move pinmux configs to the right devices
arm: kirkwood: buffalo linkstation: move pinmux configs to the right devices
arm: kirkwood: keymile: move pinmux configs to the right devices
arm: kirkwood: ns2: move pinmux configs to the right devices
arm: kirkwood: iomega ix2-200: move pinmux configs to the right devices
arm: kirkwood: iconnect: move pinmux configs to the right devices
arm: kirkwood: iconnect: give meaningful names to pinmux configs
arm: kirkwood: ib62x0: move pinmux configs to the right devices
arm: kirkwood: guruplug: move pinmux configs to the right devices
arm: kirkwood: goflexnet: move pinmux configs to the right devices
arm: kirkwood: dreamplug: move pinmux configs to the right devices
arm: kirkwood: dockstar: move pinmux configs to the right devices
arm: kirkwood: dlink dns: move pinmux configs to the right devices
...
Boris BREZILLON [Fri, 24 May 2013 10:05:56 +0000 (10:05 +0000)] 
ARM: at91/dt: add pinctrl definition for at91 tc blocks
This patch adds pinctrl configurations for at91 Timer Counter blocks.
These pin definitions can be referenced by "atmel,tcb-pwm" devices to
setup pins as PWM output for instance.
Signed-off-by: Boris BREZILLON <b.brezillon@overkiz.com>
[nicolas.ferre@atmel.com: switch to pinctrl pre-processor macros]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Wenyou Yang [Fri, 31 May 2013 03:11:33 +0000 (11:11 +0800)] 
ARM: at91/dts: add the watchdog nodes for at91 boards
boards include:
at91sam9263ek, at91sam9g20ek, at91sam9m10g45ek, at91sam9n12ek, at91sam9x5ek
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Wenyou Yang [Fri, 31 May 2013 03:10:02 +0000 (11:10 +0800)]
ARM: at91/dtsi: add the watchdog nodes for at91 SoC
at91sam9x5, at91sam9n12
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 23 May 2013 22:52:06 +0000 (06:52 +0800)] 
ARM: at91: drop non DT: Calao USB-A96x
as now we have full DT support of those board
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 23 May 2013 22:50:12 +0000 (06:50 +0800)]
ARM: at91: dt: add Calao USB-A9G20 low power version
the low power version have a mmc-spi
eanble mmc-spi and RV3029C2 RTC in at91_dt_defconfig
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 23 May 2013 23:00:22 +0000 (07:00 +0800)]
ARM: at91: dt: usb-a9263: add dataflash support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 23 May 2013 22:49:43 +0000 (06:49 +0800)]
ARM: at91: dt: usb-a9263: update shutdown controller
enable rtt and wakeup button (5 msec low)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Jean-Christophe PLAGNIOL-VILLARD [Thu, 23 May 2013 22:48:22 +0000 (06:48 +0800)]
ARM: at91: dt: usb-a9260: update shutdown controller
enable rtt and wakeup button (5 msec low)
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Jean-Christophe PLAGNIOL-VILLARD [Sun, 26 May 2013 08:55:59 +0000 (16:55 +0800)]
ARM: at91: dt: sam9260: add i2c gpio pinctrl
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Nicolas Ferre [Fri, 31 May 2013 14:41:02 +0000 (16:41 +0200)] 
ARM: at91: switch Fox G20 board .dts to pre-processor defines
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Douglas Gilbert [Thu, 18 Apr 2013 12:53:06 +0000 (14:53 +0200)] 
ARM: at91: add Acme Systems Fox G20 board
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
[nicolas.ferre@atmel.com: re-arranging nodes, removing nodes and some comments]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Nicolas Ferre [Thu, 18 Apr 2013 10:36:25 +0000 (12:36 +0200)]
ARM: at91/at91-ariag25.dts: UART0/1 nodes are disabled
UART0 is moved to generic at91sam9x5.dtsi file.
Both uarts are "disabled" as the corresponding pins on
Aria documentation are shown as GPIOs.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Nicolas Ferre [Thu, 18 Apr 2013 08:52:45 +0000 (10:52 +0200)]
ARM: at91/at91sam9x5.dtsi: add UART0/1 nodes
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Nicolas Ferre [Thu, 18 Apr 2013 08:35:08 +0000 (10:35 +0200)]
ARM: at91/at91-ariag25.dts: add RTC node
Reported-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Nicolas Ferre [Thu, 18 Apr 2013 08:13:21 +0000 (10:13 +0200)]
ARM: at91: at91sam9x5 RTC is not compatible with at91rm9200 one
Due to a bug with RTC IMR, we cannot consider at91sam9x5 RTC compatible
with the previous one. Modify DT compatibility string, even if the driver
is not yet modified to take it into account.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Olof Johansson [Tue, 28 May 2013 04:20:17 +0000 (21:20 -0700)]
Merge tag 'nomadik-dt-for-arm-soc' of git://git./linux/kernel/git/linusw/linux-nomadik into next/dt
From Linus Walleij:
Device tree patches for the Nomadik machine:
- Move clock registration to the device tree
- Support probing the MTU timer from the device tree
- Register user LED and user key in the device tree
- Update defconfig to account for user LED and user key
- Move pin control mappings to the device tree
* tag 'nomadik-dt-for-arm-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-nomadik:
ARM: nomadik: move the pin configuration to DT
ARM: nomadik: add led and key for S8815
ARM: nomadik: register clocksource from device tree
ARM: nomadik: convert all clocks except timer to dt
clocksource: nomadik-mtu: support of probe
Signed-off-by: Olof Johansson <olof@lixom.net>
Valentin Longchamp [Mon, 27 May 2013 15:55:26 +0000 (17:55 +0200)] 
ARM: kirkwood: add i2c-gpio controller for km_kirkwood
This controller is used to access the reset management FPGA of the
km_kirkwood boards.
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Valentin Longchamp [Mon, 27 May 2013 15:40:32 +0000 (17:40 +0200)]
ARM: kirkwood: refactor dtsi to largest common nodes
Some kirkwood variants (for instance present in the prestera SoCs) do
not have all the peripherals whose nodes are declared in
kirkwood.dtsi. These missing peripherals are SATA, SDIO, and RTC.
As discussed in [1], to avoid that these missing peripherals get
initialized which could result in system hangs when accessing
undocumented/not present HW registers, their corresponding OF nodes
should not get declared at all for some kirkwood variants.
The corresponding OF nodes of these peripherals thus are moved from
kirkwood.dtsi to the kirkwood-628x.dtsi files so that they still are
initialized for these variants where they are present.
[1]
http://lists.infradead.org/pipermail/linux-arm-kernel/2013-May/167154.html
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:58 +0000 (11:44 +0200)] 
arm: kirkwood: openblocks-a6: add support for Init button
The Kirkwood-based PlatHome OpenBlocks A6 board has an Init button
connected to MPP pin 38. This commit adds support for this button.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Atsushi Yamagata <yamagata@plathome.co.jp>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:57 +0000 (11:44 +0200)]
arm: kirkwood: openblocks-a6: group pinmux configurations
Instead of having one separate pinmux configuration for each LED, for
each GPIO of the GPIO header, for each DIP switch, this patch groups
them together in configurations that make sense together: LEDs on one
side, GPIOs of the GPIO header on another side, and DIP switches on
yet another side.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Atsushi Yamagata <yamagata@plathome.co.jp>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:56 +0000 (11:44 +0200)]
arm: kirkwood: ts219: move pinmux configs to the right devices
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-By: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:55 +0000 (11:44 +0200)]
arm: kirkwood: topkick: move pinmux configs to the right devices
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-By: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:54 +0000 (11:44 +0200)]
arm: kirkwood: openblocks_a6: move pinmux configs to the right devices
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Atsushi Yamagata <yamagata@plathome.co.jp>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:53 +0000 (11:44 +0200)]
arm: kirkwood: nsa310: move pinmux configs to the right devices
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:52 +0000 (11:44 +0200)]
arm: kirkwood: readynas: move pinmux configs to the right devices
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:51 +0000 (11:44 +0200)]
arm: kirkwood: mplcec4: move pinmux configs to the right devices
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:50 +0000 (11:44 +0200)]
arm: kirkwood: buffalo linkstation: move pinmux configs to the right devices
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:49 +0000 (11:44 +0200)]
arm: kirkwood: keymile: move pinmux configs to the right devices
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:48 +0000 (11:44 +0200)]
arm: kirkwood: ns2: move pinmux configs to the right devices
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:47 +0000 (11:44 +0200)]
arm: kirkwood: iomega ix2-200: move pinmux configs to the right devices
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
Note that some of the LEDs pinmux configurations are kept in the
pinctrl node, because they are not used by the gpio-leds driver.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:46 +0000 (11:44 +0200)]
arm: kirkwood: iconnect: move pinmux configs to the right devices
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:45 +0000 (11:44 +0200)]
arm: kirkwood: iconnect: give meaningful names to pinmux configs
The Kirkwood iConnect Device Tree is currently using totally
meaningless names for the pinmux configuration: pmx_gpio_XY.
This patch fixes that by using some more meaningful names such as
pmx_button_power.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:44 +0000 (11:44 +0200)]
arm: kirkwood: ib62x0: move pinmux configs to the right devices
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:43 +0000 (11:44 +0200)]
arm: kirkwood: guruplug: move pinmux configs to the right devices
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:42 +0000 (11:44 +0200)]
arm: kirkwood: goflexnet: move pinmux configs to the right devices
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:41 +0000 (11:44 +0200)]
arm: kirkwood: dreamplug: move pinmux configs to the right devices
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:40 +0000 (11:44 +0200)]
arm: kirkwood: dockstar: move pinmux configs to the right devices
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:39 +0000 (11:44 +0200)]
arm: kirkwood: dlink dns: move pinmux configs to the right devices
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Thomas Petazzoni [Fri, 24 May 2013 09:44:38 +0000 (11:44 +0200)]
arm: kirkwood: cloudbox: move pinmux configs to the right devices
When the pinmux mechanism was added in Kirkwood, the device driver
core was not yet providing the possibility of attaching pinmux
configurations to all devices, drivers had to do it explicitly, and
not all drivers were doing this.
Now that the driver core does that in a generic way, it makes sense to
attach the pinmux configuration to their corresponding devices.
This allows the pinctrl subsystem to show in debugfs to which device
is related which pins, for example:
pin 41 (PIN41): gpio-leds.1 mvebu-gpio:41 function gpio group mpp41
pin 42 (PIN42): gpio-leds.1 mvebu-gpio:42 function gpio group mpp42
pin 43 (PIN43): gpio-leds.1 mvebu-gpio:43 function gpio group mpp43
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Linus Torvalds [Sun, 26 May 2013 23:00:47 +0000 (16:00 -0700)] 
Linux 3.10-rc3
Manfred Spraul [Sun, 26 May 2013 09:08:52 +0000 (11:08 +0200)] 
ipc/sem.c: Fix missing wakeups in do_smart_update_queue()
do_smart_update_queue() is called when an operation (semop,
semctl(SETVAL), semctl(SETALL), ...) modified the array. It must check
which of the sleeping tasks can proceed.
do_smart_update_queue() missed a few wakeups:
- if a sleeping complex op was completed, then all per-semaphore queues
must be scanned - not only those that were modified by *sops
- if a sleeping simple op proceeded, then the global queue must be
scanned again
And:
- the test for "|sops == NULL) before scanning the global queue is not
required: If the global queue is empty, then it doesn't need to be
scanned - regardless of the reason for calling do_smart_update_queue()
The patch is not optimized, i.e. even completing a wait-for-zero
operation causes a rescan. This is done to keep the patch as simple as
possible.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Acked-by: Davidlohr Bueso <davidlohr.bueso@hp.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Walleij [Fri, 24 May 2013 19:56:38 +0000 (21:56 +0200)] 
ARM: nomadik: move the pin configuration to DT
This moves the pin configuration for the Nomadik over to the
device tree using Gabriel's bindings. Remove the auxdata
nailing down the name of the pin controller as this is no
longer necessary.
Cc: Gabriel Fernandez <gabriel.fernandez@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Walleij [Sat, 18 May 2013 21:55:13 +0000 (23:55 +0200)]
ARM: nomadik: add led and key for S8815
This adds device tree hunks for the LED and userbutton on the
USB S8815 board, and set up a heartbeat trigger on the LED and
an escape key on the user button. Alter the defconfig to enable
these standard DT-enabled GPIO drivers.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Linus Torvalds [Sun, 26 May 2013 19:33:05 +0000 (12:33 -0700)]
Merge tag 'nfs-for-3.10-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Stable fix to prevent an rpc_task wakeup race
- Fix a NFSv4.1 session drain deadlock
- Fix a NFSv4/v4.1 mount regression when not running rpc.gssd
- Ensure auth_gss pipe detection works in namespaces
- Fix SETCLIENTID fallback if rpcsec_gss is not available
* tag 'nfs-for-3.10-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Fix SETCLIENTID fallback if GSS is not available
SUNRPC: Prevent an rpc_task wakeup race
NFSv4.1 Fix a pNFS session draining deadlock
SUNRPC: Convert auth_gss pipe detection to work in namespaces
SUNRPC: Faster detection if gssd is actually running
SUNRPC: Fix a bug in gss_create_upcall
Linus Torvalds [Sun, 26 May 2013 16:52:26 +0000 (09:52 -0700)]
Merge tag 'edac_fixes_for_3.10' of git://git./linux/kernel/git/bp/bp
Pull amd64 edac fix from Borislav Petkov:
"A sysfs file permissions correction"
* tag 'edac_fixes_for_3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
amd64_edac: Fix bogus sysfs file permissions
Linus Torvalds [Sun, 26 May 2013 16:36:31 +0000 (09:36 -0700)]
Merge branch 'parisc-for-3.10' of git://git./linux/kernel/git/deller/parisc-linux
Pull parisc fixes from Helge Deller:
"This time we made the kernel- and interruption stack allocation
reentrant which fixed some strange kernel crashes (specifically
protection ID traps).
Furthemore this patchset fixes the interrupt stack in UP and SMP
configurations by using native locking instructions. And finally
usage of floating point calculations on parisc were disabled in the
MPILIB."
* 'parisc-for-3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: fix irq stack on UP and SMP
parisc/superio: Use module_pci_driver to register driver
parisc: make interrupt and interruption stack allocation reentrant
parisc: show number of FPE and unaligned access handler calls in /proc/interrupts
parisc: add additional parisc git tree to MAINTAINERS file
parisc: use PAGE_SHIFT instead of hardcoded value 12 in pacache.S
parisc: add rp5470 entry to machine database
MPILIB: disable usage of floating point registers on parisc
Linus Torvalds [Sun, 26 May 2013 16:35:02 +0000 (09:35 -0700)]
Merge tag 'for-linus-v3.10-rc3' of git://oss.sgi.com/xfs/xfs
Pull xfs fixes from Ben Myers:
"Here are fixes for corruption on 512 byte filesystems, a rounding
error, a use-after-free, some flags to fix lockdep reports, and
several fixes related to CRCs. We have a somewhat larger post -rc1
queue than usual due to fixes related to the CRC feature we merged for
3.10:
- Fix for corruption with FSX on 512 byte blocksize filesystems
- Fix rounding error in xfs_free_file_space
- Fix use-after-free with extent free intents
- Add several missing KM_NOFS flags to fix lockdep reports
- Several fixes for CRC related code"
* tag 'for-linus-v3.10-rc3' of git://oss.sgi.com/xfs/xfs:
xfs: remote attribute lookups require the value length
xfs: xfs_attr_shortform_allfit() does not handle attr3 format.
xfs: xfs_da3_node_read_verify() doesn't handle XFS_ATTR3_LEAF_MAGIC
xfs: fix missing KM_NOFS tags to keep lockdep happy
xfs: Don't reference the EFI after it is freed
xfs: fix rounding in xfs_free_file_space
xfs: fix sub-page blocksize data integrity writes
Linus Torvalds [Sun, 26 May 2013 03:32:49 +0000 (20:32 -0700)]
Merge tag 'for-v3.10-fixes' of git://git.infradead.org/battery-2.6
Pull bettery fixes from Anton Vorontsov:
"Last minute one-liners: wrong kfree usage fix, module alias fixup and
kconfig adjustments"
* tag 'for-v3.10-fixes' of git://git.infradead.org/battery-2.6:
pm2301_charger: Fix module alias prefix
wm831x_backup: Fix wrong kfree call for devdata->backup.name
bq27x00: Fix I2C dependency in KConfig
lp8788-charger: Fix kconfig dependency
Linus Torvalds [Sun, 26 May 2013 03:32:00 +0000 (20:32 -0700)]
Merge tag 'pm+acpi-3.10-rc3' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
- Additional CPU ID for the intel_pstate driver from Dirk Brandewie.
- More cpufreq fixes related to ARM big.LITTLE support and locking from
Viresh Kumar.
- VIA C7 cpufreq build fix from Rafał Bilski.
- ACPI power management fix making it possible to use device power
states regardless of the CONFIG_PM setting from Rafael J Wysocki.
- New ACPI video blacklist item from Bastian Triller.
* tag 'pm+acpi-3.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / video: Add "Asus UL30A" to ACPI video detect blacklist
cpufreq: arm_big_little_dt: Instantiate as platform_driver
cpufreq: arm_big_little_dt: Register driver only if DT has valid data
cpufreq / e_powersaver: Fix linker error when ACPI processor is a module
cpufreq / intel_pstate: Add additional supported CPU ID
cpufreq: Drop rwsem lock around CPUFREQ_GOV_POLICY_EXIT
ACPI / PM: Allow device power states to be used for CONFIG_PM unset
Linus Torvalds [Sun, 26 May 2013 03:30:31 +0000 (20:30 -0700)]
Merge branch 'fixes' of git://git.infradead.org/users/vkoul/slave-dma
Pull slave-dma fixes from Vinod Koul:
"We have two patches from Andy & Rafael fixing the Lynxpoint dma"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
ACPI / LPSS: register clock device for Lynxpoint DMA properly
dma: acpi-dma: parse CSRT to extract additional resources
Kyle McMartin [Sat, 25 May 2013 16:54:08 +0000 (12:54 -0400)] 
score: remove redundant kcore_list entries
kcore_vmalloc is in fs/proc/kcore.c and kcore_mem is unused across
the tree. Noticed while grepping the tree for some other kcore stuff.
(score looks pretty unmaintained to me.)
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sat, 25 May 2013 17:06:20 +0000 (10:06 -0700)]
Merge tag 'arc-v3.10-fixes' of git://git./linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
- Fallouts/wreckage of Cache Flush optimizations / aliasing dcache
support
- Fix for an interesting bug where piped input to grep was getting
mysteriously clobbered
* tag 'arc-v3.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: lazy dcache flush broke gdb in non-aliasing configs
ARC: Use enough bits for determining page's cache color
ARC: Brown paper bag bug in macro for checking cache color
ARC: copy_(to|from)_user() to honor usermode-access permissions
ARC: [mm] Prevent stray dcache lines after__sync_icache_dcach()
ARC: [TB10x] Remove redundant abilis,simple-pinctrl mechanism
Linus Torvalds [Sat, 25 May 2013 17:05:24 +0000 (10:05 -0700)]
Merge branch 'fixes' of git://git.linaro.org/people/rmk/linux-arm
Pull ARM fixes from Russell King:
"Just three this time, all really quite small"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: 7729/1: vfp: ensure VFP_arch is non-zero when VFP is not supported
ARM: 7727/1: remove the .vm_mm value from gate_vma
ARM: 7723/1: crypto: sha1-armv4-large.S: fix SP handling
Vineet Gupta [Sat, 25 May 2013 08:34:25 +0000 (14:04 +0530)] 
ARC: lazy dcache flush broke gdb in non-aliasing configs
gdbserver inserting a breakpoint ends up calling copy_user_page() for a
code page. The generic version of which (non-aliasing config) didn't set
the PG_arch_1 bit hence update_mmu_cache() didn't sync dcache/icache for
corresponding dynamic loader code page - causing garbade to be executed.
So now aliasing versions of copy_user_highpage()/clear_page() are made
default. There is no significant overhead since all of special alias
handling code is compiled out for non-aliasing build
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Linus Torvalds [Sat, 25 May 2013 01:12:15 +0000 (18:12 -0700)]
Merge branch 'akpm' (incoming from Andrew Morton)
Merge fixes from Andrew Morton:
"A bunch of fixes and one simple fbdev driver which missed the merge
window because people will still talking about it (to no great
effect)."
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (30 commits)
aio: fix kioctx not being freed after cancellation at exit time
mm/pagewalk.c: walk_page_range should avoid VM_PFNMAP areas
drivers/rtc/rtc-max8998.c: check for pdata presence before dereferencing
ocfs2: goto out_unlock if ocfs2_get_clusters_nocache() failed in ocfs2_fiemap()
random: fix accounting race condition with lockless irq entropy_count update
drivers/char/random.c: fix priming of last_data
mm/memory_hotplug.c: fix printk format warnings
nilfs2: fix issue of nilfs_set_page_dirty() for page at EOF boundary
drivers/block/brd.c: fix brd_lookup_page() race
fbdev: FB_GOLDFISH should depend on HAS_DMA
drivers/rtc/rtc-pl031.c: pass correct pointer to free_irq()
auditfilter.c: fix kernel-doc warnings
aio: fix io_getevents documentation
revert "selftest: add simple test for soft-dirty bit"
drivers/leds/leds-ot200.c: fix error caused by shifted mask
mm/THP: use pmd_populate() to update the pmd with pgtable_t pointer
linux/kernel.h: fix kernel-doc warning
mm compaction: fix of improper cache flush in migration code
rapidio/tsi721: fix bug in MSI interrupt handling
hfs: avoid crash in hfs_bnode_create
...
Linus Torvalds [Fri, 24 May 2013 23:27:37 +0000 (16:27 -0700)]
Merge tag 'fixes-for-linus' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We didn't have any fixes sent up for -rc2, so this is a slightly
larger batch. A bit all over the place platform-wise; OMAP, at91,
marvell, renesas, sunxi, ux500, etc.
I tried to summarize highlights but there isn't a whole lot to point
out. Lots of little things fixed all over. A couple of defconfig
updates due to new/changing options."
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (44 commits)
ARM: at91/sama5: fix incorrect PMC pcr div definition
ARM: at91/dt: fix macb pinctrl_macb_rmii_mii_alt definition
ARM: at91: at91sam9n12: move external irq declatation to DT
ARM: shmobile: marzen: Use error values in usb_power_*
ARM: tegra: defconfig fixes
ARM: nomadik: fix IRQ assignment for SMC ethernet
ARM: vt8500: Add missing NULL terminator in dt_compat
clk: tegra: add ac97 controller clock
clk: tegra: remove USB from clk init table
ARM: dts: mvebu: Fix wrong the address reg value for the L2-cache node
ARM: plat-orion: Fix num_resources and id for ge10 and ge11
ARM: OMAP2+: hwmod: Remove sysc slave idle and auto idle apis
SERIAL: OMAP: Remove the slave idle handling from the driver
ARM: OMAP2+: serial: Remove the un-used slave idle hooks
ARM: OMAP2+: hwmod-data: UART IP needs software control to manage sidle modes
ARM: OMAP2+: hwmod: Add a new flag to handle SIDLE in SWSUP only in active
ARM: OMAP2+: hwmod: Fix sidle programming in _enable_sysc()/_idle_sysc()
arm: mvebu: fix the 'ranges' property to handle PCIe
ARM: mvebu: select ARCH_REQUIRE_GPIOLIB for mvebu platform
ARM: AM33XX: Add missing .clkdm_name to clkdiv32k_ick clock
...
Benjamin LaHaise [Fri, 24 May 2013 22:55:38 +0000 (15:55 -0700)] 
aio: fix kioctx not being freed after cancellation at exit time
The recent changes overhauling fs/aio.c introduced a bug that results in
the kioctx not being freed when outstanding kiocbs are cancelled at
exit_aio() time. Specifically, a kiocb that is cancelled has its
completion events discarded by batch_complete_aio(), which then fails to
wake up the process stuck in free_ioctx(). Fix this by modifying the
wait_event() condition in free_ioctx() appropriately.
This patch was tested with the cancel operation in the thread based code
posted yesterday.
[akpm@linux-foundation.org: fix build]
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Josh Boyer <jwboyer@redhat.com>
Cc: Zach Brown <zab@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Cliff Wickman [Fri, 24 May 2013 22:55:36 +0000 (15:55 -0700)] 
mm/pagewalk.c: walk_page_range should avoid VM_PFNMAP areas
A panic can be caused by simply cat'ing /proc/<pid>/smaps while an
application has a VM_PFNMAP range. It happened in-house when a
benchmarker was trying to decipher the memory layout of his program.
/proc/<pid>/smaps and similar walks through a user page table should not
be looking at VM_PFNMAP areas.
Certain tests in walk_page_range() (specifically split_huge_page_pmd())
assume that all the mapped PFN's are backed with page structures. And
this is not usually true for VM_PFNMAP areas. This can result in panics
on kernel page faults when attempting to address those page structures.
There are a half dozen callers of walk_page_range() that walk through a
task's entire page table (as N. Horiguchi pointed out). So rather than
change all of them, this patch changes just walk_page_range() to ignore
VM_PFNMAP areas.
The logic of hugetlb_vma() is moved back into walk_page_range(), as we
want to test any vma in the range.
VM_PFNMAP areas are used by:
- graphics memory manager gpu/drm/drm_gem.c
- global reference unit sgi-gru/grufile.c
- sgi special memory char/mspec.c
- and probably several out-of-tree modules
[akpm@linux-foundation.org: remove now-unused hugetlb_vma() stub]
Signed-off-by: Cliff Wickman <cpw@sgi.com>
Reviewed-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Andrea Arcangeli <aarcange@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: David Sterba <dsterba@suse.cz>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: KOSAKI Motohiro <kosaki.motohiro@gmail.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Tomasz Figa [Fri, 24 May 2013 22:55:35 +0000 (15:55 -0700)] 
drivers/rtc/rtc-max8998.c: check for pdata presence before dereferencing
Currently the driver can crash with a NULL pointer dereference if no
pdata is provided, despite of successful registration of the MFD part.
This patch fixes the problem by adding a NULL check before dereferencing
the pdata pointer.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Sachin Kamat <sachin.kamat@linaro.org>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joseph Qi [Fri, 24 May 2013 22:55:34 +0000 (15:55 -0700)] 
ocfs2: goto out_unlock if ocfs2_get_clusters_nocache() failed in ocfs2_fiemap()
Last time we found there is lock/unlock bug in ocfs2_file_aio_write, and
then we did a thorough search for all lock resources in
ocfs2_inode_info, including rw, inode and open lockres and found this
bug. My kernel version is 3.0.13, and it is also in the lastest version
3.9. In ocfs2_fiemap, once ocfs2_get_clusters_nocache failed, it should
goto out_unlock instead of out, because we need release buffer head, up
read alloc sem and unlock inode.
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Reviewed-by: Jie Liu <jeff.liu@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Acked-by: Sunil Mushran <sunil.mushran@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jiri Kosina [Fri, 24 May 2013 22:55:33 +0000 (15:55 -0700)] 
random: fix accounting race condition with lockless irq entropy_count update
Commit
902c098a3663 ("random: use lockless techniques in the interrupt
path") turned IRQ path from being spinlock protected into lockless
cmpxchg-retry update.
That commit removed r->lock serialization between crediting entropy bits
from IRQ context and accounting when extracting entropy on userspace
read path, but didn't turn the r->entropy_count reads/updates in
account() to use cmpxchg as well.
It has been observed, that under certain circumstances this leads to
read() on /dev/urandom to return 0 (EOF), as r->entropy_count gets
corrupted and becomes negative, which in turn results in propagating 0
all the way from account() to the actual read() call.
Convert the accounting code to be the proper lockless counterpart of
what has been partially done by
902c098a3663.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Greg KH <greg@kroah.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jarod Wilson [Fri, 24 May 2013 22:55:31 +0000 (15:55 -0700)] 
drivers/char/random.c: fix priming of last_data
Commit
ec8f02da9ea5 ("random: prime last_data value per fips
requirements") added priming of last_data per fips requirements.
Unfortuantely, it did so in a way that can lead to multiple threads all
incrementing nbytes, but only one actually doing anything with the extra
data, which leads to some fun random corruption and panics.
The fix is to simply do everything needed to prime last_data in a single
shot, so there's no window for multiple cpus to increment nbytes -- in
fact, we won't even increment or decrement nbytes anymore, we'll just
extract the needed EXTRACT_SIZE one time per pool and then carry on with
the normal routine.
All these changes have been tested across multiple hosts and
architectures where panics were previously encoutered. The code changes
are are strictly limited to areas only touched when when booted in fips
mode.
This change should also go into 3.8-stable, to make the myriads of fips
users on 3.8.x happy.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Jan Stodola <jstodola@redhat.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Matt Mackall <mpm@selenic.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Fri, 24 May 2013 22:55:30 +0000 (15:55 -0700)] 
mm/memory_hotplug.c: fix printk format warnings
Fix printk format warnings in mm/memory_hotplug.c by using "%pa":
mm/memory_hotplug.c: warning: format '%llx' expects argument of type 'long long unsigned int', but argument 2 has type 'resource_size_t' [-Wformat]
mm/memory_hotplug.c: warning: format '%llx' expects argument of type 'long long unsigned int', but argument 3 has type 'resource_size_t' [-Wformat]
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ryusuke Konishi [Fri, 24 May 2013 22:55:29 +0000 (15:55 -0700)] 
nilfs2: fix issue of nilfs_set_page_dirty() for page at EOF boundary
nilfs2: fix issue of nilfs_set_page_dirty for page at EOF boundary
DESCRIPTION:
There are use-cases when NILFS2 file system (formatted with block size
lesser than 4 KB) can be remounted in RO mode because of encountering of
"broken bmap" issue.
The issue was reported by Anthony Doggett <Anthony2486@interfaces.org.uk>:
"The machine I've been trialling nilfs on is running Debian Testing,
Linux version 3.2.0-4-686-pae (debian-kernel@lists.debian.org) (gcc
version 4.6.3 (Debian 4.6.3-14) ) #1 SMP Debian 3.2.35-2), but I've
also reproduced it (identically) with Debian Unstable amd64 and Debian
Experimental (using the 3.8-trunk kernel). The problematic partitions
were formatted with "mkfs.nilfs2 -b 1024 -B 8192"."
SYMPTOMS:
(1) System log contains error messages likewise:
[63102.496756] nilfs_direct_assign: invalid pointer: 0
[63102.496786] NILFS error (device dm-17): nilfs_bmap_assign: broken bmap (inode number=28)
[63102.496798]
[63102.524403] Remounting filesystem read-only
(2) The NILFS2 file system is remounted in RO mode.
REPRODUSING PATH:
(1) Create volume group with name "unencrypted" by means of vgcreate utility.
(2) Run script (prepared by Anthony Doggett <Anthony2486@interfaces.org.uk>):
----------------[BEGIN SCRIPT]--------------------
VG=unencrypted
lvcreate --size 2G --name ntest $VG
mkfs.nilfs2 -b 1024 -B 8192 /dev/mapper/$VG-ntest
mkdir /var/tmp/n
mkdir /var/tmp/n/ntest
mount /dev/mapper/$VG-ntest /var/tmp/n/ntest
mkdir /var/tmp/n/ntest/thedir
cd /var/tmp/n/ntest/thedir
sleep 2
date
darcs init
sleep 2
dmesg|tail -n 5
date
darcs whatsnew || true
date
sleep 2
dmesg|tail -n 5
----------------[END SCRIPT]--------------------
REPRODUCIBILITY: 100%
INVESTIGATION:
As it was discovered, the issue takes place during segment
construction after executing such sequence of user-space operations:
open("_darcs/index", O_RDWR|O_CREAT|O_NOCTTY, 0666) = 7
fstat(7, {st_mode=S_IFREG|0644, st_size=0, ...}) = 0
ftruncate(7, 60)
The error message "NILFS error (device dm-17): nilfs_bmap_assign: broken
bmap (inode number=28)" takes place because of trying to get block
number for third block of the file with logical offset #3072 bytes. As
it is possible to see from above output, the file has 60 bytes of the
whole size. So, it is enough one block (1 KB in size) allocation for
the whole file. Trying to operate with several blocks instead of one
takes place because of discovering several dirty buffers for this file
in nilfs_segctor_scan_file() method.
The root cause of this issue is in nilfs_set_page_dirty function which
is called just before writing to an mmapped page.
When nilfs_page_mkwrite function handles a page at EOF boundary, it
fills hole blocks only inside EOF through __block_page_mkwrite().
The __block_page_mkwrite() function calls set_page_dirty() after filling
hole blocks, thus nilfs_set_page_dirty function (=
a_ops->set_page_dirty) is called. However, the current implementation
of nilfs_set_page_dirty() wrongly marks all buffers dirty even for page
at EOF boundary.
As a result, buffers outside EOF are inconsistently marked dirty and
queued for write even though they are not mapped with nilfs_get_block
function.
FIX:
This modifies nilfs_set_page_dirty() not to mark hole blocks dirty.
Thanks to Vyacheslav Dubeyko for his effort on analysis and proposals
for this issue.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Reported-by: Anthony Doggett <Anthony2486@interfaces.org.uk>
Reported-by: Vyacheslav Dubeyko <slava@dubeyko.com>
Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Tested-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Brian Behlendorf [Fri, 24 May 2013 22:55:28 +0000 (15:55 -0700)] 
drivers/block/brd.c: fix brd_lookup_page() race
The index on the page must be set before it is inserted in the radix
tree. Otherwise there is a small race which can occur during lookup
where the page can be found with the incorrect index. This will trigger
the BUG_ON() in brd_lookup_page().
Signed-off-by: Brian Behlendorf <behlendorf1@llnl.gov>
Reported-by: Chris Wedgwood <cw@f00f.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Geert Uytterhoeven [Fri, 24 May 2013 22:55:27 +0000 (15:55 -0700)] 
fbdev: FB_GOLDFISH should depend on HAS_DMA
If NO_DMA=y:
drivers/built-in.o: In function `goldfish_fb_remove':
drivers/video/goldfishfb.c:301: undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `goldfish_fb_probe':
drivers/video/goldfishfb.c:247: undefined reference to `dma_alloc_coherent'
drivers/video/goldfishfb.c:280: undefined reference to `dma_free_coherent'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Lars-Peter Clausen [Fri, 24 May 2013 22:55:26 +0000 (15:55 -0700)] 
drivers/rtc/rtc-pl031.c: pass correct pointer to free_irq()
free_irq() expects the same pointer that was passed to request_irq(),
otherwise the IRQ is not freed.
The issue was found using the following coccinelle script:
<smpl>
@r1@
type T;
T devid;
@@
request_irq(..., devid)
@r2@
type r1.T;
T devid;
position p;
@@
free_irq@p(..., devid)
@@
position p != r2.p;
@@
*free_irq@p(...)
</smpl>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Fri, 24 May 2013 22:55:25 +0000 (15:55 -0700)]
auditfilter.c: fix kernel-doc warnings
Fix kernel-doc warnings in kernel/auditfilter.c:
Warning(kernel/auditfilter.c:1029): Excess function parameter 'loginuid' description in 'audit_receive_filter'
Warning(kernel/auditfilter.c:1029): Excess function parameter 'sessionid' description in 'audit_receive_filter'
Warning(kernel/auditfilter.c:1029): Excess function parameter 'sid' description in 'audit_receive_filter'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Eric Paris <eparis@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Moyer [Fri, 24 May 2013 22:55:24 +0000 (15:55 -0700)] 
aio: fix io_getevents documentation
In reviewing man pages, I noticed that io_getevents is documented to
update the timeout that gets passed into the library call. This doesn't
happen in kernel space or in the library (even though it's documented to
do so in both places). Unless there is objection, I'd like to fix the
comments/docs to match the code (I will also update the man page upon
consensus).
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
Acked-by: Cyril Hrubis <chrubis@suse.cz>
Acked-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Andrew Morton [Fri, 24 May 2013 22:55:23 +0000 (15:55 -0700)] 
revert "selftest: add simple test for soft-dirty bit"
Revert commit
58c7be84fec8 ("selftest: add simple test for soft-dirty
bit"). This is the self test for Pavel's pagemap2 patches which didn't
actually get merged.
Reported-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Christian Gmeiner [Fri, 24 May 2013 22:55:22 +0000 (15:55 -0700)] 
drivers/leds/leds-ot200.c: fix error caused by shifted mask
During the development of this driver an in-house register documentation
was used. The last week some integration tests were done and this
problem was found. It turned out that the released register
documentation is wrong.
The fix is very simple: shift all masks by one.
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Cc: Bryan Wu <cooloney@gmail.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Aneesh Kumar K.V [Fri, 24 May 2013 22:55:21 +0000 (15:55 -0700)] 
mm/THP: use pmd_populate() to update the pmd with pgtable_t pointer
We should not use set_pmd_at to update pmd_t with pgtable_t pointer.
set_pmd_at is used to set pmd with huge pte entries and architectures
like ppc64, clear few flags from the pte when saving a new entry.
Without this change we observe bad pte errors like below on ppc64 with
THP enabled.
BUG: Bad page map in process ld mm=0xc000001ee39f4780 pte:
7fc3f37848000001 pmd:
c000001ec0000000
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Andrea Arcangeli <aarcange@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Randy Dunlap [Fri, 24 May 2013 22:55:20 +0000 (15:55 -0700)]
linux/kernel.h: fix kernel-doc warning
Fix kernel-doc warning in <linux/kernel.h>:
Warning(include/linux/kernel.h:590): No description found for parameter 'ip'
scripts/kernel-doc cannot handle macros, functions, or function
prototypes between the function or macro that is being documented and
its definition, so move these prototypes above the function that is
being documented.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Leonid Yegoshin [Fri, 24 May 2013 22:55:18 +0000 (15:55 -0700)] 
mm compaction: fix of improper cache flush in migration code
Page 'new' during MIGRATION can't be flushed with flush_cache_page().
Using flush_cache_page(vma, addr, pfn) is justified only if the page is
already placed in process page table, and that is done right after
flush_cache_page(). But without it the arch function has no knowledge
of process PTE and does nothing.
Besides that, flush_cache_page() flushes an application cache page, but
the kernel has a different page virtual address and dirtied it.
Replace it with flush_dcache_page(new) which is the proper usage.
The old page is flushed in try_to_unmap_one() before migration.
This bug takes place in Sead3 board with M14Kc MIPS CPU without cache
aliasing (but Harvard arch - separate I and D cache) in tight memory
environment (128MB) each 1-3days on SOAK test. It fails in cc1 during
kernel build (SIGILL, SIGBUS, SIGSEG) if CONFIG_COMPACTION is switched
ON.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: Leonid Yegoshin <yegoshin@mips.com>
Acked-by: Rik van Riel <riel@redhat.com>
Cc: Michal Hocko <mhocko@suse.cz>
Acked-by: Mel Gorman <mgorman@suse.de>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Miller <davem@davemloft.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexandre Bounine [Fri, 24 May 2013 22:55:17 +0000 (15:55 -0700)] 
rapidio/tsi721: fix bug in MSI interrupt handling
Fix bug in MSI interrupt handling which causes loss of event
notifications.
Typical indication of lost MSI interrupts are stalled message and
doorbell transfers between RapidIO endpoints. To avoid loss of MSI
interrupts all interrupts from the device must be disabled on entering
the interrupt handler routine and re-enabled when exiting it.
Re-enabling device interrupts will trigger new MSI message(s) if Tsi721
registered new events since entering interrupt handler routine.
This patch is applicable to kernel versions starting from v3.2.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Jeff Mahoney [Fri, 24 May 2013 22:55:16 +0000 (15:55 -0700)] 
hfs: avoid crash in hfs_bnode_create
Commit
634725a92938 ("hfs: cleanup HFS+ prints") removed the BUG_ON in
hfs_bnode_create in hfsplus. This patch removes it from the hfs version
and avoids an fsfuzzer crash.
Signed-off-by: Jeff Mahoney <jeffm@suse.com>
Acked-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Vyacheslav Dubeyko <slava@dubeyko.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Johannes Weiner [Fri, 24 May 2013 22:55:15 +0000 (15:55 -0700)] 
mm: memcg: remove incorrect VM_BUG_ON for swap cache pages in uncharge
Commit
0c59b89c81ea ("mm: memcg: push down PageSwapCache check into
uncharge entry functions") added a VM_BUG_ON() on PageSwapCache in the
uncharge path after checking that page flag once, assuming that the
state is stable in all paths, but this is not the case and the condition
triggers in user environments. An uncharge after the last page table
reference to the page goes away can race with reclaim adding the page to
swap cache.
Swap cache pages are usually uncharged when they are freed after
swapout, from a path that also handles swap usage accounting and memcg
lifetime management. However, since the last page table reference is
gone and thus no references to the swap slot left, the swap slot will be
freed shortly when reclaim attempts to write the page to disk. The
whole swap accounting is not even necessary.
So while the race condition for which this VM_BUG_ON was added is real
and actually existed all along, there are no negative effects. Remove
the VM_BUG_ON again.
Reported-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reported-by: Lingzhu Xiang <lxiang@redhat.com>
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Hugh Dickins <hughd@google.com>
Acked-by: Michal Hocko <mhocko@suse.cz>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stephen Warren [Fri, 24 May 2013 22:55:13 +0000 (15:55 -0700)] 
drivers/video: implement a simple framebuffer driver
A simple frame-buffer describes a raw memory region that may be rendered
to, with the assumption that the display hardware has already been set
up to scan out from that buffer.
This is useful in cases where a bootloader exists and has set up the
display hardware, but a Linux driver doesn't yet exist for the display
hardware.
Examples use-cases include:
* The built-in LCD panels on the Samsung ARM chromebook, and Tegra
devices, and likely many other ARM or embedded systems. These cannot
yet be supported using a full graphics driver, since the panel control
should be provided by the CDF (Common Display Framework), which has been
stuck in design/review for quite some time. One could support these
panels using custom SoC-specific code, but there is a desire to use
common infra-structure rather than having each SoC vendor invent their
own code, hence the desire to wait for CDF.
* Hardware for which a full graphics driver is not yet available, and
the path to obtain one upstream isn't yet clear. For example, the
Raspberry Pi.
* Any hardware in early stages of upstreaming, before a full graphics
driver has been tackled. This driver can provide a graphical boot
console (even full X support) much earlier in the upstreaming process,
thus making new SoC or board support more generally useful earlier.
[akpm@linux-foundation.org: make simplefb_formats[] static]
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Acked-by: Olof Johansson <olof@lixom.net>
Cc: Rob Clark <robclark@gmail.com>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Joseph Qi [Fri, 24 May 2013 22:55:12 +0000 (15:55 -0700)]
ocfs2: unlock rw lock if inode lock failed
In ocfs2_file_aio_write(), it does ocfs2_rw_lock() first and then
ocfs2_inode_lock().
But if ocfs2_inode_lock() failed, it goes to out_sems without unlocking
rw lock. This will cause a bug in ocfs2_lock_res_free() when testing
res->l_ex_holders, which is increased in __ocfs2_cluster_lock() and
decreased in __ocfs2_cluster_unlock().
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Li Zefan <lizefan@huawei.com>
Cc: "Duyongfeng (B)" <du.duyongfeng@huawei.com>
Acked-by: Sunil Mushran <sunil.mushran@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Xiao Guangrong [Fri, 24 May 2013 22:55:11 +0000 (15:55 -0700)] 
mm: mmu_notifier: re-fix freed page still mapped in secondary MMU
Commit
751efd8610d3 ("mmu_notifier_unregister NULL Pointer deref and
multiple ->release()") breaks the fix
3ad3d901bbcf ("mm: mmu_notifier:
fix freed page still mapped in secondary MMU").
Since hlist_for_each_entry_rcu() is changed now, we can not revert that
patch directly, so this patch reverts the commit and simply fix the bug
spotted by that patch
This bug spotted by commit
751efd8610d3 is:
There is a race condition between mmu_notifier_unregister() and
__mmu_notifier_release().
Assume two tasks, one calling mmu_notifier_unregister() as a result
of a filp_close() ->flush() callout (task A), and the other calling
mmu_notifier_release() from an mmput() (task B).
A B
t1 srcu_read_lock()
t2 if (!hlist_unhashed())
t3 srcu_read_unlock()
t4 srcu_read_lock()
t5 hlist_del_init_rcu()
t6 synchronize_srcu()
t7 srcu_read_unlock()
t8 hlist_del_rcu() <--- NULL pointer deref.
This can be fixed by using hlist_del_init_rcu instead of hlist_del_rcu.
The another issue spotted in the commit is "multiple ->release()
callouts", we needn't care it too much because it is really rare (e.g,
can not happen on kvm since mmu-notify is unregistered after
exit_mmap()) and the later call of multiple ->release should be fast
since all the pages have already been released by the first call.
Anyway, this issue should be fixed in a separate patch.
-stable suggestions: Any version that has commit
751efd8610d3 need to be
backported. I find the oldest version has this commit is 3.0-stable.
[akpm@linux-foundation.org: tweak comments]
Signed-off-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Tested-by: Robin Holt <holt@sgi.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Imre Deak [Fri, 24 May 2013 22:55:09 +0000 (15:55 -0700)] 
wait: fix false timeouts when using wait_event_timeout()
Many callers of the wait_event_timeout() and
wait_event_interruptible_timeout() expect that the return value will be
positive if the specified condition becomes true before the timeout
elapses. However, at the moment this isn't guaranteed. If the wake-up
handler is delayed enough, the time remaining until timeout will be
calculated as 0 - and passed back as a return value - even if the
condition became true before the timeout has passed.
Fix this by returning at least 1 if the condition becomes true. This
semantic is in line with what wait_for_condition_timeout() does; see
commit
bb10ed09 ("sched: fix wait_for_completion_timeout() spurious
failure under heavy load").
Daniel said "We have 3 instances of this bug in drm/i915. One case even
where we switch between the interruptible and not interruptible
wait_event_timeout variants, foolishly presuming they have the same
semantics. I very much like this."
One such bug is reported at
https://bugs.freedesktop.org/show_bug.cgi?id=64133
Signed-off-by: Imre Deak <imre.deak@intel.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Cc: "Paul E. McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Dave Jones <davej@redhat.com>
Cc: Lukas Czerner <lczerner@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OGAWA Hirofumi [Fri, 24 May 2013 22:55:08 +0000 (15:55 -0700)] 
fat: fix possible overflow for fat_clusters
Intermediate value of fat_clusters can be overflowed on 32bits arch.
Reported-by: Krzysztof Strasburger <strasbur@chkw386.ch.pwr.wroc.pl>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alexandre Bounine [Fri, 24 May 2013 22:55:07 +0000 (15:55 -0700)]
rapidio: documentation update for enumeration changes
Update RapidIO documentation to reflect changes made to
enumeration/discovery build configuration and user space triggering
mechanism.
Signed-off-by: Alexandre Bounine <alexandre.bounine@idt.com>
Cc: Matt Porter <mporter@kernel.crashing.org>
Cc: Li Yang <leoli@freescale.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Andre van Herk <andre.van.herk@Prodrive.nl>
Cc: Micha Nelissen <micha.nelissen@Prodrive.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This page took 0.052428 seconds and 5 git commands to generate.
projects / deliverable / linux.git / log
