Commit | Line | Data |
---|---|---|
1da177e4 LT |
1 | /* |
2 | * Device driver for the thermostats & fan controller of the | |
3 | * Apple G5 "PowerMac7,2" desktop machines. | |
4 | * | |
5 | * (c) Copyright IBM Corp. 2003-2004 | |
6 | * | |
7 | * Maintained by: Benjamin Herrenschmidt | |
8 | * <benh@kernel.crashing.org> | |
9 | * | |
10 | * | |
11 | * The algorithm used is the PID control algorithm, used the same | |
12 | * way the published Darwin code does, using the same values that | |
13 | * are present in the Darwin 7.0 snapshot property lists. | |
14 | * | |
15 | * As far as the CPUs control loops are concerned, I use the | |
16 | * calibration & PID constants provided by the EEPROM, | |
17 | * I do _not_ embed any value from the property lists, as the ones | |
18 | * provided by Darwin 7.0 seem to always have an older version that | |
19 | * what I've seen on the actual computers. | |
20 | * It would be interesting to verify that though. Darwin has a | |
21 | * version code of 1.0.0d11 for all control loops it seems, while | |
22 | * so far, the machines EEPROMs contain a dataset versioned 1.0.0f | |
23 | * | |
24 | * Darwin doesn't provide source to all parts, some missing | |
25 | * bits like the AppleFCU driver or the actual scale of some | |
26 | * of the values returned by sensors had to be "guessed" some | |
27 | * way... or based on what Open Firmware does. | |
28 | * | |
29 | * I didn't yet figure out how to get the slots power consumption | |
30 | * out of the FCU, so that part has not been implemented yet and | |
31 | * the slots fan is set to a fixed 50% PWM, hoping this value is | |
32 | * safe enough ... | |
33 | * | |
34 | * Note: I have observed strange oscillations of the CPU control | |
35 | * loop on a dual G5 here. When idle, the CPU exhaust fan tend to | |
36 | * oscillates slowly (over several minutes) between the minimum | |
37 | * of 300RPMs and approx. 1000 RPMs. I don't know what is causing | |
38 | * this, it could be some incorrect constant or an error in the | |
39 | * way I ported the algorithm, or it could be just normal. I | |
40 | * don't have full understanding on the way Apple tweaked the PID | |
41 | * algorithm for the CPU control, it is definitely not a standard | |
42 | * implementation... | |
43 | * | |
44 | * TODO: - Check MPU structure version/signature | |
45 | * - Add things like /sbin/overtemp for non-critical | |
46 | * overtemp conditions so userland can take some policy | |
47 | * decisions, like slewing down CPUs | |
48 | * - Deal with fan and i2c failures in a better way | |
49 | * - Maybe do a generic PID based on params used for | |
50 | * U3 and Drives ? Definitely need to factor code a bit | |
51 | * bettter... also make sensor detection more robust using | |
52 | * the device-tree to probe for them | |
53 | * - Figure out how to get the slots consumption and set the | |
54 | * slots fan accordingly | |
55 | * | |
56 | * History: | |
57 | * | |
58 | * Nov. 13, 2003 : 0.5 | |
59 | * - First release | |
60 | * | |
61 | * Nov. 14, 2003 : 0.6 | |
62 | * - Read fan speed from FCU, low level fan routines now deal | |
63 | * with errors & check fan status, though higher level don't | |
64 | * do much. | |
65 | * - Move a bunch of definitions to .h file | |
66 | * | |
67 | * Nov. 18, 2003 : 0.7 | |
68 | * - Fix build on ppc64 kernel | |
69 | * - Move back statics definitions to .c file | |
70 | * - Avoid calling schedule_timeout with a negative number | |
71 | * | |
72 | * Dec. 18, 2003 : 0.8 | |
73 | * - Fix typo when reading back fan speed on 2 CPU machines | |
74 | * | |
75 | * Mar. 11, 2004 : 0.9 | |
76 | * - Rework code accessing the ADC chips, make it more robust and | |
77 | * closer to the chip spec. Also make sure it is configured properly, | |
78 | * I've seen yet unexplained cases where on startup, I would have stale | |
79 | * values in the configuration register | |
80 | * - Switch back to use of target fan speed for PID, thus lowering | |
81 | * pressure on i2c | |
82 | * | |
83 | * Oct. 20, 2004 : 1.1 | |
84 | * - Add device-tree lookup for fan IDs, should detect liquid cooling | |
85 | * pumps when present | |
86 | * - Enable driver for PowerMac7,3 machines | |
87 | * - Split the U3/Backside cooling on U3 & U3H versions as Darwin does | |
88 | * - Add new CPU cooling algorithm for machines with liquid cooling | |
89 | * - Workaround for some PowerMac7,3 with empty "fan" node in the devtree | |
90 | * - Fix a signed/unsigned compare issue in some PID loops | |
91 | * | |
92 | * Mar. 10, 2005 : 1.2 | |
93 | * - Add basic support for Xserve G5 | |
94 | * - Retreive pumps min/max from EEPROM image in device-tree (broken) | |
95 | * - Use min/max macros here or there | |
96 | * - Latest darwin updated U3H min fan speed to 20% PWM | |
97 | * | |
861fa773 BH |
98 | * July. 06, 2006 : 1.3 |
99 | * - Fix setting of RPM fans on Xserve G5 (they were going too fast) | |
100 | * - Add missing slots fan control loop for Xserve G5 | |
101 | * - Lower fixed slots fan speed from 50% to 40% on desktop G5s. We | |
102 | * still can't properly implement the control loop for these, so let's | |
103 | * reduce the noise a little bit, it appears that 40% still gives us | |
104 | * a pretty good air flow | |
105 | * - Add code to "tickle" the FCU regulary so it doesn't think that | |
106 | * we are gone while in fact, the machine just didn't need any fan | |
107 | * speed change lately | |
108 | * | |
1da177e4 LT |
109 | */ |
110 | ||
1da177e4 LT |
111 | #include <linux/types.h> |
112 | #include <linux/module.h> | |
113 | #include <linux/errno.h> | |
114 | #include <linux/kernel.h> | |
115 | #include <linux/delay.h> | |
116 | #include <linux/sched.h> | |
1da177e4 LT |
117 | #include <linux/slab.h> |
118 | #include <linux/init.h> | |
119 | #include <linux/spinlock.h> | |
1da177e4 LT |
120 | #include <linux/wait.h> |
121 | #include <linux/reboot.h> | |
122 | #include <linux/kmod.h> | |
123 | #include <linux/i2c.h> | |
1da177e4 LT |
124 | #include <asm/prom.h> |
125 | #include <asm/machdep.h> | |
126 | #include <asm/io.h> | |
127 | #include <asm/system.h> | |
128 | #include <asm/sections.h> | |
129 | #include <asm/of_device.h> | |
5e655772 | 130 | #include <asm/macio.h> |
7eebde70 | 131 | #include <asm/of_platform.h> |
1da177e4 LT |
132 | |
133 | #include "therm_pm72.h" | |
134 | ||
861fa773 | 135 | #define VERSION "1.3" |
1da177e4 LT |
136 | |
137 | #undef DEBUG | |
138 | ||
139 | #ifdef DEBUG | |
140 | #define DBG(args...) printk(args) | |
141 | #else | |
142 | #define DBG(args...) do { } while(0) | |
143 | #endif | |
144 | ||
145 | ||
146 | /* | |
147 | * Driver statics | |
148 | */ | |
149 | ||
150 | static struct of_device * of_dev; | |
151 | static struct i2c_adapter * u3_0; | |
152 | static struct i2c_adapter * u3_1; | |
153 | static struct i2c_adapter * k2; | |
154 | static struct i2c_client * fcu; | |
155 | static struct cpu_pid_state cpu_state[2]; | |
156 | static struct basckside_pid_params backside_params; | |
157 | static struct backside_pid_state backside_state; | |
158 | static struct drives_pid_state drives_state; | |
159 | static struct dimm_pid_state dimms_state; | |
861fa773 | 160 | static struct slots_pid_state slots_state; |
1da177e4 LT |
161 | static int state; |
162 | static int cpu_count; | |
163 | static int cpu_pid_type; | |
164 | static pid_t ctrl_task; | |
165 | static struct completion ctrl_complete; | |
166 | static int critical_state; | |
167 | static int rackmac; | |
168 | static s32 dimm_output_clamp; | |
861fa773 BH |
169 | static int fcu_rpm_shift; |
170 | static int fcu_tickle_ticks; | |
1da177e4 LT |
171 | static DECLARE_MUTEX(driver_lock); |
172 | ||
173 | /* | |
174 | * We have 3 types of CPU PID control. One is "split" old style control | |
175 | * for intake & exhaust fans, the other is "combined" control for both | |
176 | * CPUs that also deals with the pumps when present. To be "compatible" | |
177 | * with OS X at this point, we only use "COMBINED" on the machines that | |
178 | * are identified as having the pumps (though that identification is at | |
179 | * least dodgy). Ultimately, we could probably switch completely to this | |
180 | * algorithm provided we hack it to deal with the UP case | |
181 | */ | |
182 | #define CPU_PID_TYPE_SPLIT 0 | |
183 | #define CPU_PID_TYPE_COMBINED 1 | |
184 | #define CPU_PID_TYPE_RACKMAC 2 | |
185 | ||
186 | /* | |
187 | * This table describes all fans in the FCU. The "id" and "type" values | |
188 | * are defaults valid for all earlier machines. Newer machines will | |
189 | * eventually override the table content based on the device-tree | |
190 | */ | |
191 | struct fcu_fan_table | |
192 | { | |
193 | char* loc; /* location code */ | |
194 | int type; /* 0 = rpm, 1 = pwm, 2 = pump */ | |
195 | int id; /* id or -1 */ | |
196 | }; | |
197 | ||
198 | #define FCU_FAN_RPM 0 | |
199 | #define FCU_FAN_PWM 1 | |
200 | ||
201 | #define FCU_FAN_ABSENT_ID -1 | |
202 | ||
203 | #define FCU_FAN_COUNT ARRAY_SIZE(fcu_fans) | |
204 | ||
205 | struct fcu_fan_table fcu_fans[] = { | |
206 | [BACKSIDE_FAN_PWM_INDEX] = { | |
207 | .loc = "BACKSIDE,SYS CTRLR FAN", | |
208 | .type = FCU_FAN_PWM, | |
209 | .id = BACKSIDE_FAN_PWM_DEFAULT_ID, | |
210 | }, | |
211 | [DRIVES_FAN_RPM_INDEX] = { | |
212 | .loc = "DRIVE BAY", | |
213 | .type = FCU_FAN_RPM, | |
214 | .id = DRIVES_FAN_RPM_DEFAULT_ID, | |
215 | }, | |
216 | [SLOTS_FAN_PWM_INDEX] = { | |
217 | .loc = "SLOT,PCI FAN", | |
218 | .type = FCU_FAN_PWM, | |
219 | .id = SLOTS_FAN_PWM_DEFAULT_ID, | |
220 | }, | |
221 | [CPUA_INTAKE_FAN_RPM_INDEX] = { | |
222 | .loc = "CPU A INTAKE", | |
223 | .type = FCU_FAN_RPM, | |
224 | .id = CPUA_INTAKE_FAN_RPM_DEFAULT_ID, | |
225 | }, | |
226 | [CPUA_EXHAUST_FAN_RPM_INDEX] = { | |
227 | .loc = "CPU A EXHAUST", | |
228 | .type = FCU_FAN_RPM, | |
229 | .id = CPUA_EXHAUST_FAN_RPM_DEFAULT_ID, | |
230 | }, | |
231 | [CPUB_INTAKE_FAN_RPM_INDEX] = { | |
232 | .loc = "CPU B INTAKE", | |
233 | .type = FCU_FAN_RPM, | |
234 | .id = CPUB_INTAKE_FAN_RPM_DEFAULT_ID, | |
235 | }, | |
236 | [CPUB_EXHAUST_FAN_RPM_INDEX] = { | |
237 | .loc = "CPU B EXHAUST", | |
238 | .type = FCU_FAN_RPM, | |
239 | .id = CPUB_EXHAUST_FAN_RPM_DEFAULT_ID, | |
240 | }, | |
241 | /* pumps aren't present by default, have to be looked up in the | |
242 | * device-tree | |
243 | */ | |
244 | [CPUA_PUMP_RPM_INDEX] = { | |
245 | .loc = "CPU A PUMP", | |
246 | .type = FCU_FAN_RPM, | |
247 | .id = FCU_FAN_ABSENT_ID, | |
248 | }, | |
249 | [CPUB_PUMP_RPM_INDEX] = { | |
250 | .loc = "CPU B PUMP", | |
251 | .type = FCU_FAN_RPM, | |
252 | .id = FCU_FAN_ABSENT_ID, | |
253 | }, | |
254 | /* Xserve fans */ | |
255 | [CPU_A1_FAN_RPM_INDEX] = { | |
256 | .loc = "CPU A 1", | |
257 | .type = FCU_FAN_RPM, | |
258 | .id = FCU_FAN_ABSENT_ID, | |
259 | }, | |
260 | [CPU_A2_FAN_RPM_INDEX] = { | |
261 | .loc = "CPU A 2", | |
262 | .type = FCU_FAN_RPM, | |
263 | .id = FCU_FAN_ABSENT_ID, | |
264 | }, | |
265 | [CPU_A3_FAN_RPM_INDEX] = { | |
266 | .loc = "CPU A 3", | |
267 | .type = FCU_FAN_RPM, | |
268 | .id = FCU_FAN_ABSENT_ID, | |
269 | }, | |
270 | [CPU_B1_FAN_RPM_INDEX] = { | |
271 | .loc = "CPU B 1", | |
272 | .type = FCU_FAN_RPM, | |
273 | .id = FCU_FAN_ABSENT_ID, | |
274 | }, | |
275 | [CPU_B2_FAN_RPM_INDEX] = { | |
276 | .loc = "CPU B 2", | |
277 | .type = FCU_FAN_RPM, | |
278 | .id = FCU_FAN_ABSENT_ID, | |
279 | }, | |
280 | [CPU_B3_FAN_RPM_INDEX] = { | |
281 | .loc = "CPU B 3", | |
282 | .type = FCU_FAN_RPM, | |
283 | .id = FCU_FAN_ABSENT_ID, | |
284 | }, | |
285 | }; | |
286 | ||
287 | /* | |
288 | * i2c_driver structure to attach to the host i2c controller | |
289 | */ | |
290 | ||
291 | static int therm_pm72_attach(struct i2c_adapter *adapter); | |
292 | static int therm_pm72_detach(struct i2c_adapter *adapter); | |
293 | ||
294 | static struct i2c_driver therm_pm72_driver = | |
295 | { | |
a33ca232 | 296 | .driver = { |
a33ca232 LR |
297 | .name = "therm_pm72", |
298 | }, | |
1da177e4 LT |
299 | .attach_adapter = therm_pm72_attach, |
300 | .detach_adapter = therm_pm72_detach, | |
301 | }; | |
302 | ||
303 | /* | |
304 | * Utility function to create an i2c_client structure and | |
305 | * attach it to one of u3 adapters | |
306 | */ | |
307 | static struct i2c_client *attach_i2c_chip(int id, const char *name) | |
308 | { | |
309 | struct i2c_client *clt; | |
310 | struct i2c_adapter *adap; | |
311 | ||
312 | if (id & 0x200) | |
313 | adap = k2; | |
314 | else if (id & 0x100) | |
315 | adap = u3_1; | |
316 | else | |
317 | adap = u3_0; | |
318 | if (adap == NULL) | |
319 | return NULL; | |
320 | ||
321 | clt = kmalloc(sizeof(struct i2c_client), GFP_KERNEL); | |
322 | if (clt == NULL) | |
323 | return NULL; | |
324 | memset(clt, 0, sizeof(struct i2c_client)); | |
325 | ||
326 | clt->addr = (id >> 1) & 0x7f; | |
327 | clt->adapter = adap; | |
328 | clt->driver = &therm_pm72_driver; | |
329 | strncpy(clt->name, name, I2C_NAME_SIZE-1); | |
330 | ||
331 | if (i2c_attach_client(clt)) { | |
332 | printk(KERN_ERR "therm_pm72: Failed to attach to i2c ID 0x%x\n", id); | |
333 | kfree(clt); | |
334 | return NULL; | |
335 | } | |
336 | return clt; | |
337 | } | |
338 | ||
339 | /* | |
340 | * Utility function to get rid of the i2c_client structure | |
341 | * (will also detach from the adapter hopepfully) | |
342 | */ | |
343 | static void detach_i2c_chip(struct i2c_client *clt) | |
344 | { | |
345 | i2c_detach_client(clt); | |
346 | kfree(clt); | |
347 | } | |
348 | ||
349 | /* | |
350 | * Here are the i2c chip access wrappers | |
351 | */ | |
352 | ||
353 | static void initialize_adc(struct cpu_pid_state *state) | |
354 | { | |
355 | int rc; | |
356 | u8 buf[2]; | |
357 | ||
358 | /* Read ADC the configuration register and cache it. We | |
359 | * also make sure Config2 contains proper values, I've seen | |
360 | * cases where we got stale grabage in there, thus preventing | |
361 | * proper reading of conv. values | |
362 | */ | |
363 | ||
364 | /* Clear Config2 */ | |
365 | buf[0] = 5; | |
366 | buf[1] = 0; | |
367 | i2c_master_send(state->monitor, buf, 2); | |
368 | ||
369 | /* Read & cache Config1 */ | |
370 | buf[0] = 1; | |
371 | rc = i2c_master_send(state->monitor, buf, 1); | |
372 | if (rc > 0) { | |
373 | rc = i2c_master_recv(state->monitor, buf, 1); | |
374 | if (rc > 0) { | |
375 | state->adc_config = buf[0]; | |
376 | DBG("ADC config reg: %02x\n", state->adc_config); | |
377 | /* Disable shutdown mode */ | |
378 | state->adc_config &= 0xfe; | |
379 | buf[0] = 1; | |
380 | buf[1] = state->adc_config; | |
381 | rc = i2c_master_send(state->monitor, buf, 2); | |
382 | } | |
383 | } | |
384 | if (rc <= 0) | |
385 | printk(KERN_ERR "therm_pm72: Error reading ADC config" | |
386 | " register !\n"); | |
387 | } | |
388 | ||
389 | static int read_smon_adc(struct cpu_pid_state *state, int chan) | |
390 | { | |
391 | int rc, data, tries = 0; | |
392 | u8 buf[2]; | |
393 | ||
394 | for (;;) { | |
395 | /* Set channel */ | |
396 | buf[0] = 1; | |
397 | buf[1] = (state->adc_config & 0x1f) | (chan << 5); | |
398 | rc = i2c_master_send(state->monitor, buf, 2); | |
399 | if (rc <= 0) | |
400 | goto error; | |
401 | /* Wait for convertion */ | |
402 | msleep(1); | |
403 | /* Switch to data register */ | |
404 | buf[0] = 4; | |
405 | rc = i2c_master_send(state->monitor, buf, 1); | |
406 | if (rc <= 0) | |
407 | goto error; | |
408 | /* Read result */ | |
409 | rc = i2c_master_recv(state->monitor, buf, 2); | |
410 | if (rc < 0) | |
411 | goto error; | |
412 | data = ((u16)buf[0]) << 8 | (u16)buf[1]; | |
413 | return data >> 6; | |
414 | error: | |
415 | DBG("Error reading ADC, retrying...\n"); | |
416 | if (++tries > 10) { | |
417 | printk(KERN_ERR "therm_pm72: Error reading ADC !\n"); | |
418 | return -1; | |
419 | } | |
420 | msleep(10); | |
421 | } | |
422 | } | |
423 | ||
424 | static int read_lm87_reg(struct i2c_client * chip, int reg) | |
425 | { | |
426 | int rc, tries = 0; | |
427 | u8 buf; | |
428 | ||
429 | for (;;) { | |
430 | /* Set address */ | |
431 | buf = (u8)reg; | |
432 | rc = i2c_master_send(chip, &buf, 1); | |
433 | if (rc <= 0) | |
434 | goto error; | |
435 | rc = i2c_master_recv(chip, &buf, 1); | |
436 | if (rc <= 0) | |
437 | goto error; | |
438 | return (int)buf; | |
439 | error: | |
440 | DBG("Error reading LM87, retrying...\n"); | |
441 | if (++tries > 10) { | |
442 | printk(KERN_ERR "therm_pm72: Error reading LM87 !\n"); | |
443 | return -1; | |
444 | } | |
445 | msleep(10); | |
446 | } | |
447 | } | |
448 | ||
449 | static int fan_read_reg(int reg, unsigned char *buf, int nb) | |
450 | { | |
451 | int tries, nr, nw; | |
452 | ||
453 | buf[0] = reg; | |
454 | tries = 0; | |
455 | for (;;) { | |
456 | nw = i2c_master_send(fcu, buf, 1); | |
457 | if (nw > 0 || (nw < 0 && nw != -EIO) || tries >= 100) | |
458 | break; | |
459 | msleep(10); | |
460 | ++tries; | |
461 | } | |
462 | if (nw <= 0) { | |
463 | printk(KERN_ERR "Failure writing address to FCU: %d", nw); | |
464 | return -EIO; | |
465 | } | |
466 | tries = 0; | |
467 | for (;;) { | |
468 | nr = i2c_master_recv(fcu, buf, nb); | |
469 | if (nr > 0 || (nr < 0 && nr != ENODEV) || tries >= 100) | |
470 | break; | |
471 | msleep(10); | |
472 | ++tries; | |
473 | } | |
474 | if (nr <= 0) | |
475 | printk(KERN_ERR "Failure reading data from FCU: %d", nw); | |
476 | return nr; | |
477 | } | |
478 | ||
479 | static int fan_write_reg(int reg, const unsigned char *ptr, int nb) | |
480 | { | |
481 | int tries, nw; | |
482 | unsigned char buf[16]; | |
483 | ||
484 | buf[0] = reg; | |
485 | memcpy(buf+1, ptr, nb); | |
486 | ++nb; | |
487 | tries = 0; | |
488 | for (;;) { | |
489 | nw = i2c_master_send(fcu, buf, nb); | |
490 | if (nw > 0 || (nw < 0 && nw != EIO) || tries >= 100) | |
491 | break; | |
492 | msleep(10); | |
493 | ++tries; | |
494 | } | |
495 | if (nw < 0) | |
496 | printk(KERN_ERR "Failure writing to FCU: %d", nw); | |
497 | return nw; | |
498 | } | |
499 | ||
500 | static int start_fcu(void) | |
501 | { | |
502 | unsigned char buf = 0xff; | |
503 | int rc; | |
504 | ||
505 | rc = fan_write_reg(0xe, &buf, 1); | |
506 | if (rc < 0) | |
507 | return -EIO; | |
508 | rc = fan_write_reg(0x2e, &buf, 1); | |
509 | if (rc < 0) | |
510 | return -EIO; | |
861fa773 BH |
511 | rc = fan_read_reg(0, &buf, 1); |
512 | if (rc < 0) | |
513 | return -EIO; | |
514 | fcu_rpm_shift = (buf == 1) ? 2 : 3; | |
515 | printk(KERN_DEBUG "FCU Initialized, RPM fan shift is %d\n", | |
516 | fcu_rpm_shift); | |
517 | ||
1da177e4 LT |
518 | return 0; |
519 | } | |
520 | ||
521 | static int set_rpm_fan(int fan_index, int rpm) | |
522 | { | |
523 | unsigned char buf[2]; | |
861fa773 | 524 | int rc, id, min, max; |
1da177e4 LT |
525 | |
526 | if (fcu_fans[fan_index].type != FCU_FAN_RPM) | |
527 | return -EINVAL; | |
528 | id = fcu_fans[fan_index].id; | |
529 | if (id == FCU_FAN_ABSENT_ID) | |
530 | return -EINVAL; | |
531 | ||
861fa773 BH |
532 | min = 2400 >> fcu_rpm_shift; |
533 | max = 56000 >> fcu_rpm_shift; | |
534 | ||
535 | if (rpm < min) | |
536 | rpm = min; | |
537 | else if (rpm > max) | |
538 | rpm = max; | |
539 | buf[0] = rpm >> (8 - fcu_rpm_shift); | |
540 | buf[1] = rpm << fcu_rpm_shift; | |
1da177e4 LT |
541 | rc = fan_write_reg(0x10 + (id * 2), buf, 2); |
542 | if (rc < 0) | |
543 | return -EIO; | |
544 | return 0; | |
545 | } | |
546 | ||
547 | static int get_rpm_fan(int fan_index, int programmed) | |
548 | { | |
549 | unsigned char failure; | |
550 | unsigned char active; | |
551 | unsigned char buf[2]; | |
552 | int rc, id, reg_base; | |
553 | ||
554 | if (fcu_fans[fan_index].type != FCU_FAN_RPM) | |
555 | return -EINVAL; | |
556 | id = fcu_fans[fan_index].id; | |
557 | if (id == FCU_FAN_ABSENT_ID) | |
558 | return -EINVAL; | |
559 | ||
560 | rc = fan_read_reg(0xb, &failure, 1); | |
561 | if (rc != 1) | |
562 | return -EIO; | |
563 | if ((failure & (1 << id)) != 0) | |
564 | return -EFAULT; | |
565 | rc = fan_read_reg(0xd, &active, 1); | |
566 | if (rc != 1) | |
567 | return -EIO; | |
568 | if ((active & (1 << id)) == 0) | |
569 | return -ENXIO; | |
570 | ||
571 | /* Programmed value or real current speed */ | |
572 | reg_base = programmed ? 0x10 : 0x11; | |
573 | rc = fan_read_reg(reg_base + (id * 2), buf, 2); | |
574 | if (rc != 2) | |
575 | return -EIO; | |
576 | ||
861fa773 | 577 | return (buf[0] << (8 - fcu_rpm_shift)) | buf[1] >> fcu_rpm_shift; |
1da177e4 LT |
578 | } |
579 | ||
580 | static int set_pwm_fan(int fan_index, int pwm) | |
581 | { | |
582 | unsigned char buf[2]; | |
583 | int rc, id; | |
584 | ||
585 | if (fcu_fans[fan_index].type != FCU_FAN_PWM) | |
586 | return -EINVAL; | |
587 | id = fcu_fans[fan_index].id; | |
588 | if (id == FCU_FAN_ABSENT_ID) | |
589 | return -EINVAL; | |
590 | ||
591 | if (pwm < 10) | |
592 | pwm = 10; | |
593 | else if (pwm > 100) | |
594 | pwm = 100; | |
595 | pwm = (pwm * 2559) / 1000; | |
596 | buf[0] = pwm; | |
597 | rc = fan_write_reg(0x30 + (id * 2), buf, 1); | |
598 | if (rc < 0) | |
599 | return rc; | |
600 | return 0; | |
601 | } | |
602 | ||
603 | static int get_pwm_fan(int fan_index) | |
604 | { | |
605 | unsigned char failure; | |
606 | unsigned char active; | |
607 | unsigned char buf[2]; | |
608 | int rc, id; | |
609 | ||
610 | if (fcu_fans[fan_index].type != FCU_FAN_PWM) | |
611 | return -EINVAL; | |
612 | id = fcu_fans[fan_index].id; | |
613 | if (id == FCU_FAN_ABSENT_ID) | |
614 | return -EINVAL; | |
615 | ||
616 | rc = fan_read_reg(0x2b, &failure, 1); | |
617 | if (rc != 1) | |
618 | return -EIO; | |
619 | if ((failure & (1 << id)) != 0) | |
620 | return -EFAULT; | |
621 | rc = fan_read_reg(0x2d, &active, 1); | |
622 | if (rc != 1) | |
623 | return -EIO; | |
624 | if ((active & (1 << id)) == 0) | |
625 | return -ENXIO; | |
626 | ||
627 | /* Programmed value or real current speed */ | |
628 | rc = fan_read_reg(0x30 + (id * 2), buf, 1); | |
629 | if (rc != 1) | |
630 | return -EIO; | |
631 | ||
632 | return (buf[0] * 1000) / 2559; | |
633 | } | |
634 | ||
861fa773 BH |
635 | static void tickle_fcu(void) |
636 | { | |
637 | int pwm; | |
638 | ||
639 | pwm = get_pwm_fan(SLOTS_FAN_PWM_INDEX); | |
640 | ||
641 | DBG("FCU Tickle, slots fan is: %d\n", pwm); | |
642 | if (pwm < 0) | |
643 | pwm = 100; | |
644 | ||
645 | if (!rackmac) { | |
646 | pwm = SLOTS_FAN_DEFAULT_PWM; | |
647 | } else if (pwm < SLOTS_PID_OUTPUT_MIN) | |
648 | pwm = SLOTS_PID_OUTPUT_MIN; | |
649 | ||
650 | /* That is hopefully enough to make the FCU happy */ | |
651 | set_pwm_fan(SLOTS_FAN_PWM_INDEX, pwm); | |
652 | } | |
653 | ||
654 | ||
1da177e4 LT |
655 | /* |
656 | * Utility routine to read the CPU calibration EEPROM data | |
657 | * from the device-tree | |
658 | */ | |
659 | static int read_eeprom(int cpu, struct mpu_data *out) | |
660 | { | |
661 | struct device_node *np; | |
662 | char nodename[64]; | |
018a3d1d | 663 | const u8 *data; |
1da177e4 LT |
664 | int len; |
665 | ||
666 | /* prom.c routine for finding a node by path is a bit brain dead | |
667 | * and requires exact @xxx unit numbers. This is a bit ugly but | |
668 | * will work for these machines | |
669 | */ | |
670 | sprintf(nodename, "/u3@0,f8000000/i2c@f8001000/cpuid@a%d", cpu ? 2 : 0); | |
671 | np = of_find_node_by_path(nodename); | |
672 | if (np == NULL) { | |
943ffb58 | 673 | printk(KERN_ERR "therm_pm72: Failed to retrieve cpuid node from device-tree\n"); |
1da177e4 LT |
674 | return -ENODEV; |
675 | } | |
01b2726d | 676 | data = of_get_property(np, "cpuid", &len); |
1da177e4 | 677 | if (data == NULL) { |
943ffb58 | 678 | printk(KERN_ERR "therm_pm72: Failed to retrieve cpuid property from device-tree\n"); |
1da177e4 LT |
679 | of_node_put(np); |
680 | return -ENODEV; | |
681 | } | |
682 | memcpy(out, data, sizeof(struct mpu_data)); | |
683 | of_node_put(np); | |
684 | ||
685 | return 0; | |
686 | } | |
687 | ||
688 | static void fetch_cpu_pumps_minmax(void) | |
689 | { | |
690 | struct cpu_pid_state *state0 = &cpu_state[0]; | |
691 | struct cpu_pid_state *state1 = &cpu_state[1]; | |
692 | u16 pump_min = 0, pump_max = 0xffff; | |
693 | u16 tmp[4]; | |
694 | ||
695 | /* Try to fetch pumps min/max infos from eeprom */ | |
696 | ||
697 | memcpy(&tmp, &state0->mpu.processor_part_num, 8); | |
698 | if (tmp[0] != 0xffff && tmp[1] != 0xffff) { | |
699 | pump_min = max(pump_min, tmp[0]); | |
700 | pump_max = min(pump_max, tmp[1]); | |
701 | } | |
702 | if (tmp[2] != 0xffff && tmp[3] != 0xffff) { | |
703 | pump_min = max(pump_min, tmp[2]); | |
704 | pump_max = min(pump_max, tmp[3]); | |
705 | } | |
706 | ||
707 | /* Double check the values, this _IS_ needed as the EEPROM on | |
708 | * some dual 2.5Ghz G5s seem, at least, to have both min & max | |
709 | * same to the same value ... (grrrr) | |
710 | */ | |
711 | if (pump_min == pump_max || pump_min == 0 || pump_max == 0xffff) { | |
712 | pump_min = CPU_PUMP_OUTPUT_MIN; | |
713 | pump_max = CPU_PUMP_OUTPUT_MAX; | |
714 | } | |
715 | ||
716 | state0->pump_min = state1->pump_min = pump_min; | |
717 | state0->pump_max = state1->pump_max = pump_max; | |
718 | } | |
719 | ||
720 | /* | |
721 | * Now, unfortunately, sysfs doesn't give us a nice void * we could | |
722 | * pass around to the attribute functions, so we don't really have | |
723 | * choice but implement a bunch of them... | |
724 | * | |
725 | * That sucks a bit, we take the lock because FIX32TOPRINT evaluates | |
726 | * the input twice... I accept patches :) | |
727 | */ | |
728 | #define BUILD_SHOW_FUNC_FIX(name, data) \ | |
e404e274 | 729 | static ssize_t show_##name(struct device *dev, struct device_attribute *attr, char *buf) \ |
1da177e4 LT |
730 | { \ |
731 | ssize_t r; \ | |
732 | down(&driver_lock); \ | |
733 | r = sprintf(buf, "%d.%03d", FIX32TOPRINT(data)); \ | |
734 | up(&driver_lock); \ | |
735 | return r; \ | |
736 | } | |
737 | #define BUILD_SHOW_FUNC_INT(name, data) \ | |
e404e274 | 738 | static ssize_t show_##name(struct device *dev, struct device_attribute *attr, char *buf) \ |
1da177e4 LT |
739 | { \ |
740 | return sprintf(buf, "%d", data); \ | |
741 | } | |
742 | ||
743 | BUILD_SHOW_FUNC_FIX(cpu0_temperature, cpu_state[0].last_temp) | |
744 | BUILD_SHOW_FUNC_FIX(cpu0_voltage, cpu_state[0].voltage) | |
745 | BUILD_SHOW_FUNC_FIX(cpu0_current, cpu_state[0].current_a) | |
746 | BUILD_SHOW_FUNC_INT(cpu0_exhaust_fan_rpm, cpu_state[0].rpm) | |
747 | BUILD_SHOW_FUNC_INT(cpu0_intake_fan_rpm, cpu_state[0].intake_rpm) | |
748 | ||
749 | BUILD_SHOW_FUNC_FIX(cpu1_temperature, cpu_state[1].last_temp) | |
750 | BUILD_SHOW_FUNC_FIX(cpu1_voltage, cpu_state[1].voltage) | |
751 | BUILD_SHOW_FUNC_FIX(cpu1_current, cpu_state[1].current_a) | |
752 | BUILD_SHOW_FUNC_INT(cpu1_exhaust_fan_rpm, cpu_state[1].rpm) | |
753 | BUILD_SHOW_FUNC_INT(cpu1_intake_fan_rpm, cpu_state[1].intake_rpm) | |
754 | ||
755 | BUILD_SHOW_FUNC_FIX(backside_temperature, backside_state.last_temp) | |
756 | BUILD_SHOW_FUNC_INT(backside_fan_pwm, backside_state.pwm) | |
757 | ||
758 | BUILD_SHOW_FUNC_FIX(drives_temperature, drives_state.last_temp) | |
759 | BUILD_SHOW_FUNC_INT(drives_fan_rpm, drives_state.rpm) | |
760 | ||
861fa773 BH |
761 | BUILD_SHOW_FUNC_FIX(slots_temperature, slots_state.last_temp) |
762 | BUILD_SHOW_FUNC_INT(slots_fan_pwm, slots_state.pwm) | |
763 | ||
1da177e4 LT |
764 | BUILD_SHOW_FUNC_FIX(dimms_temperature, dimms_state.last_temp) |
765 | ||
766 | static DEVICE_ATTR(cpu0_temperature,S_IRUGO,show_cpu0_temperature,NULL); | |
767 | static DEVICE_ATTR(cpu0_voltage,S_IRUGO,show_cpu0_voltage,NULL); | |
768 | static DEVICE_ATTR(cpu0_current,S_IRUGO,show_cpu0_current,NULL); | |
769 | static DEVICE_ATTR(cpu0_exhaust_fan_rpm,S_IRUGO,show_cpu0_exhaust_fan_rpm,NULL); | |
770 | static DEVICE_ATTR(cpu0_intake_fan_rpm,S_IRUGO,show_cpu0_intake_fan_rpm,NULL); | |
771 | ||
772 | static DEVICE_ATTR(cpu1_temperature,S_IRUGO,show_cpu1_temperature,NULL); | |
773 | static DEVICE_ATTR(cpu1_voltage,S_IRUGO,show_cpu1_voltage,NULL); | |
774 | static DEVICE_ATTR(cpu1_current,S_IRUGO,show_cpu1_current,NULL); | |
775 | static DEVICE_ATTR(cpu1_exhaust_fan_rpm,S_IRUGO,show_cpu1_exhaust_fan_rpm,NULL); | |
776 | static DEVICE_ATTR(cpu1_intake_fan_rpm,S_IRUGO,show_cpu1_intake_fan_rpm,NULL); | |
777 | ||
778 | static DEVICE_ATTR(backside_temperature,S_IRUGO,show_backside_temperature,NULL); | |
779 | static DEVICE_ATTR(backside_fan_pwm,S_IRUGO,show_backside_fan_pwm,NULL); | |
780 | ||
781 | static DEVICE_ATTR(drives_temperature,S_IRUGO,show_drives_temperature,NULL); | |
782 | static DEVICE_ATTR(drives_fan_rpm,S_IRUGO,show_drives_fan_rpm,NULL); | |
783 | ||
861fa773 BH |
784 | static DEVICE_ATTR(slots_temperature,S_IRUGO,show_slots_temperature,NULL); |
785 | static DEVICE_ATTR(slots_fan_pwm,S_IRUGO,show_slots_fan_pwm,NULL); | |
786 | ||
1da177e4 LT |
787 | static DEVICE_ATTR(dimms_temperature,S_IRUGO,show_dimms_temperature,NULL); |
788 | ||
789 | /* | |
790 | * CPUs fans control loop | |
791 | */ | |
792 | ||
793 | static int do_read_one_cpu_values(struct cpu_pid_state *state, s32 *temp, s32 *power) | |
794 | { | |
795 | s32 ltemp, volts, amps; | |
796 | int index, rc = 0; | |
797 | ||
798 | /* Default (in case of error) */ | |
799 | *temp = state->cur_temp; | |
800 | *power = state->cur_power; | |
801 | ||
802 | if (cpu_pid_type == CPU_PID_TYPE_RACKMAC) | |
803 | index = (state->index == 0) ? | |
804 | CPU_A1_FAN_RPM_INDEX : CPU_B1_FAN_RPM_INDEX; | |
805 | else | |
806 | index = (state->index == 0) ? | |
807 | CPUA_EXHAUST_FAN_RPM_INDEX : CPUB_EXHAUST_FAN_RPM_INDEX; | |
808 | ||
809 | /* Read current fan status */ | |
810 | rc = get_rpm_fan(index, !RPM_PID_USE_ACTUAL_SPEED); | |
811 | if (rc < 0) { | |
812 | /* XXX What do we do now ? Nothing for now, keep old value, but | |
813 | * return error upstream | |
814 | */ | |
815 | DBG(" cpu %d, fan reading error !\n", state->index); | |
816 | } else { | |
817 | state->rpm = rc; | |
818 | DBG(" cpu %d, exhaust RPM: %d\n", state->index, state->rpm); | |
819 | } | |
820 | ||
821 | /* Get some sensor readings and scale it */ | |
822 | ltemp = read_smon_adc(state, 1); | |
823 | if (ltemp == -1) { | |
824 | /* XXX What do we do now ? */ | |
825 | state->overtemp++; | |
826 | if (rc == 0) | |
827 | rc = -EIO; | |
828 | DBG(" cpu %d, temp reading error !\n", state->index); | |
829 | } else { | |
830 | /* Fixup temperature according to diode calibration | |
831 | */ | |
832 | DBG(" cpu %d, temp raw: %04x, m_diode: %04x, b_diode: %04x\n", | |
833 | state->index, | |
834 | ltemp, state->mpu.mdiode, state->mpu.bdiode); | |
835 | *temp = ((s32)ltemp * (s32)state->mpu.mdiode + ((s32)state->mpu.bdiode << 12)) >> 2; | |
836 | state->last_temp = *temp; | |
837 | DBG(" temp: %d.%03d\n", FIX32TOPRINT((*temp))); | |
838 | } | |
839 | ||
840 | /* | |
841 | * Read voltage & current and calculate power | |
842 | */ | |
843 | volts = read_smon_adc(state, 3); | |
844 | amps = read_smon_adc(state, 4); | |
845 | ||
846 | /* Scale voltage and current raw sensor values according to fixed scales | |
847 | * obtained in Darwin and calculate power from I and V | |
848 | */ | |
849 | volts *= ADC_CPU_VOLTAGE_SCALE; | |
850 | amps *= ADC_CPU_CURRENT_SCALE; | |
851 | *power = (((u64)volts) * ((u64)amps)) >> 16; | |
852 | state->voltage = volts; | |
853 | state->current_a = amps; | |
854 | state->last_power = *power; | |
855 | ||
856 | DBG(" cpu %d, current: %d.%03d, voltage: %d.%03d, power: %d.%03d W\n", | |
857 | state->index, FIX32TOPRINT(state->current_a), | |
858 | FIX32TOPRINT(state->voltage), FIX32TOPRINT(*power)); | |
859 | ||
860 | return 0; | |
861 | } | |
862 | ||
863 | static void do_cpu_pid(struct cpu_pid_state *state, s32 temp, s32 power) | |
864 | { | |
865 | s32 power_target, integral, derivative, proportional, adj_in_target, sval; | |
866 | s64 integ_p, deriv_p, prop_p, sum; | |
867 | int i; | |
868 | ||
869 | /* Calculate power target value (could be done once for all) | |
870 | * and convert to a 16.16 fp number | |
871 | */ | |
872 | power_target = ((u32)(state->mpu.pmaxh - state->mpu.padjmax)) << 16; | |
873 | DBG(" power target: %d.%03d, error: %d.%03d\n", | |
874 | FIX32TOPRINT(power_target), FIX32TOPRINT(power_target - power)); | |
875 | ||
876 | /* Store temperature and power in history array */ | |
877 | state->cur_temp = (state->cur_temp + 1) % CPU_TEMP_HISTORY_SIZE; | |
878 | state->temp_history[state->cur_temp] = temp; | |
879 | state->cur_power = (state->cur_power + 1) % state->count_power; | |
880 | state->power_history[state->cur_power] = power; | |
881 | state->error_history[state->cur_power] = power_target - power; | |
882 | ||
883 | /* If first loop, fill the history table */ | |
884 | if (state->first) { | |
885 | for (i = 0; i < (state->count_power - 1); i++) { | |
886 | state->cur_power = (state->cur_power + 1) % state->count_power; | |
887 | state->power_history[state->cur_power] = power; | |
888 | state->error_history[state->cur_power] = power_target - power; | |
889 | } | |
890 | for (i = 0; i < (CPU_TEMP_HISTORY_SIZE - 1); i++) { | |
891 | state->cur_temp = (state->cur_temp + 1) % CPU_TEMP_HISTORY_SIZE; | |
892 | state->temp_history[state->cur_temp] = temp; | |
893 | } | |
894 | state->first = 0; | |
895 | } | |
896 | ||
897 | /* Calculate the integral term normally based on the "power" values */ | |
898 | sum = 0; | |
899 | integral = 0; | |
900 | for (i = 0; i < state->count_power; i++) | |
901 | integral += state->error_history[i]; | |
902 | integral *= CPU_PID_INTERVAL; | |
903 | DBG(" integral: %08x\n", integral); | |
904 | ||
905 | /* Calculate the adjusted input (sense value). | |
906 | * G_r is 12.20 | |
907 | * integ is 16.16 | |
908 | * so the result is 28.36 | |
909 | * | |
910 | * input target is mpu.ttarget, input max is mpu.tmax | |
911 | */ | |
912 | integ_p = ((s64)state->mpu.pid_gr) * (s64)integral; | |
913 | DBG(" integ_p: %d\n", (int)(integ_p >> 36)); | |
914 | sval = (state->mpu.tmax << 16) - ((integ_p >> 20) & 0xffffffff); | |
915 | adj_in_target = (state->mpu.ttarget << 16); | |
916 | if (adj_in_target > sval) | |
917 | adj_in_target = sval; | |
918 | DBG(" adj_in_target: %d.%03d, ttarget: %d\n", FIX32TOPRINT(adj_in_target), | |
919 | state->mpu.ttarget); | |
920 | ||
921 | /* Calculate the derivative term */ | |
922 | derivative = state->temp_history[state->cur_temp] - | |
923 | state->temp_history[(state->cur_temp + CPU_TEMP_HISTORY_SIZE - 1) | |
924 | % CPU_TEMP_HISTORY_SIZE]; | |
925 | derivative /= CPU_PID_INTERVAL; | |
926 | deriv_p = ((s64)state->mpu.pid_gd) * (s64)derivative; | |
927 | DBG(" deriv_p: %d\n", (int)(deriv_p >> 36)); | |
928 | sum += deriv_p; | |
929 | ||
930 | /* Calculate the proportional term */ | |
931 | proportional = temp - adj_in_target; | |
932 | prop_p = ((s64)state->mpu.pid_gp) * (s64)proportional; | |
933 | DBG(" prop_p: %d\n", (int)(prop_p >> 36)); | |
934 | sum += prop_p; | |
935 | ||
936 | /* Scale sum */ | |
937 | sum >>= 36; | |
938 | ||
939 | DBG(" sum: %d\n", (int)sum); | |
940 | state->rpm += (s32)sum; | |
941 | } | |
942 | ||
943 | static void do_monitor_cpu_combined(void) | |
944 | { | |
945 | struct cpu_pid_state *state0 = &cpu_state[0]; | |
946 | struct cpu_pid_state *state1 = &cpu_state[1]; | |
947 | s32 temp0, power0, temp1, power1; | |
948 | s32 temp_combi, power_combi; | |
949 | int rc, intake, pump; | |
950 | ||
951 | rc = do_read_one_cpu_values(state0, &temp0, &power0); | |
952 | if (rc < 0) { | |
953 | /* XXX What do we do now ? */ | |
954 | } | |
955 | state1->overtemp = 0; | |
956 | rc = do_read_one_cpu_values(state1, &temp1, &power1); | |
957 | if (rc < 0) { | |
958 | /* XXX What do we do now ? */ | |
959 | } | |
960 | if (state1->overtemp) | |
961 | state0->overtemp++; | |
962 | ||
963 | temp_combi = max(temp0, temp1); | |
964 | power_combi = max(power0, power1); | |
965 | ||
966 | /* Check tmax, increment overtemp if we are there. At tmax+8, we go | |
967 | * full blown immediately and try to trigger a shutdown | |
968 | */ | |
969 | if (temp_combi >= ((state0->mpu.tmax + 8) << 16)) { | |
970 | printk(KERN_WARNING "Warning ! Temperature way above maximum (%d) !\n", | |
971 | temp_combi >> 16); | |
f12f4d90 | 972 | state0->overtemp += CPU_MAX_OVERTEMP / 4; |
1da177e4 LT |
973 | } else if (temp_combi > (state0->mpu.tmax << 16)) |
974 | state0->overtemp++; | |
975 | else | |
976 | state0->overtemp = 0; | |
977 | if (state0->overtemp >= CPU_MAX_OVERTEMP) | |
978 | critical_state = 1; | |
979 | if (state0->overtemp > 0) { | |
980 | state0->rpm = state0->mpu.rmaxn_exhaust_fan; | |
981 | state0->intake_rpm = intake = state0->mpu.rmaxn_intake_fan; | |
6ee7fb7e | 982 | pump = state0->pump_max; |
1da177e4 LT |
983 | goto do_set_fans; |
984 | } | |
985 | ||
986 | /* Do the PID */ | |
987 | do_cpu_pid(state0, temp_combi, power_combi); | |
988 | ||
989 | /* Range check */ | |
990 | state0->rpm = max(state0->rpm, (int)state0->mpu.rminn_exhaust_fan); | |
991 | state0->rpm = min(state0->rpm, (int)state0->mpu.rmaxn_exhaust_fan); | |
992 | ||
993 | /* Calculate intake fan speed */ | |
994 | intake = (state0->rpm * CPU_INTAKE_SCALE) >> 16; | |
995 | intake = max(intake, (int)state0->mpu.rminn_intake_fan); | |
996 | intake = min(intake, (int)state0->mpu.rmaxn_intake_fan); | |
997 | state0->intake_rpm = intake; | |
998 | ||
999 | /* Calculate pump speed */ | |
1000 | pump = (state0->rpm * state0->pump_max) / | |
1001 | state0->mpu.rmaxn_exhaust_fan; | |
1002 | pump = min(pump, state0->pump_max); | |
1003 | pump = max(pump, state0->pump_min); | |
1004 | ||
1005 | do_set_fans: | |
1006 | /* We copy values from state 0 to state 1 for /sysfs */ | |
1007 | state1->rpm = state0->rpm; | |
1008 | state1->intake_rpm = state0->intake_rpm; | |
1009 | ||
1010 | DBG("** CPU %d RPM: %d Ex, %d, Pump: %d, In, overtemp: %d\n", | |
1011 | state1->index, (int)state1->rpm, intake, pump, state1->overtemp); | |
1012 | ||
1013 | /* We should check for errors, shouldn't we ? But then, what | |
1014 | * do we do once the error occurs ? For FCU notified fan | |
1015 | * failures (-EFAULT) we probably want to notify userland | |
1016 | * some way... | |
1017 | */ | |
1018 | set_rpm_fan(CPUA_INTAKE_FAN_RPM_INDEX, intake); | |
1019 | set_rpm_fan(CPUA_EXHAUST_FAN_RPM_INDEX, state0->rpm); | |
1020 | set_rpm_fan(CPUB_INTAKE_FAN_RPM_INDEX, intake); | |
1021 | set_rpm_fan(CPUB_EXHAUST_FAN_RPM_INDEX, state0->rpm); | |
1022 | ||
1023 | if (fcu_fans[CPUA_PUMP_RPM_INDEX].id != FCU_FAN_ABSENT_ID) | |
1024 | set_rpm_fan(CPUA_PUMP_RPM_INDEX, pump); | |
1025 | if (fcu_fans[CPUB_PUMP_RPM_INDEX].id != FCU_FAN_ABSENT_ID) | |
1026 | set_rpm_fan(CPUB_PUMP_RPM_INDEX, pump); | |
1027 | } | |
1028 | ||
1029 | static void do_monitor_cpu_split(struct cpu_pid_state *state) | |
1030 | { | |
1031 | s32 temp, power; | |
1032 | int rc, intake; | |
1033 | ||
1034 | /* Read current fan status */ | |
1035 | rc = do_read_one_cpu_values(state, &temp, &power); | |
1036 | if (rc < 0) { | |
1037 | /* XXX What do we do now ? */ | |
1038 | } | |
1039 | ||
1040 | /* Check tmax, increment overtemp if we are there. At tmax+8, we go | |
1041 | * full blown immediately and try to trigger a shutdown | |
1042 | */ | |
1043 | if (temp >= ((state->mpu.tmax + 8) << 16)) { | |
1044 | printk(KERN_WARNING "Warning ! CPU %d temperature way above maximum" | |
1045 | " (%d) !\n", | |
1046 | state->index, temp >> 16); | |
f12f4d90 | 1047 | state->overtemp += CPU_MAX_OVERTEMP / 4; |
1da177e4 LT |
1048 | } else if (temp > (state->mpu.tmax << 16)) |
1049 | state->overtemp++; | |
1050 | else | |
1051 | state->overtemp = 0; | |
1052 | if (state->overtemp >= CPU_MAX_OVERTEMP) | |
1053 | critical_state = 1; | |
1054 | if (state->overtemp > 0) { | |
1055 | state->rpm = state->mpu.rmaxn_exhaust_fan; | |
1056 | state->intake_rpm = intake = state->mpu.rmaxn_intake_fan; | |
1057 | goto do_set_fans; | |
1058 | } | |
1059 | ||
1060 | /* Do the PID */ | |
1061 | do_cpu_pid(state, temp, power); | |
1062 | ||
1063 | /* Range check */ | |
1064 | state->rpm = max(state->rpm, (int)state->mpu.rminn_exhaust_fan); | |
1065 | state->rpm = min(state->rpm, (int)state->mpu.rmaxn_exhaust_fan); | |
1066 | ||
1067 | /* Calculate intake fan */ | |
1068 | intake = (state->rpm * CPU_INTAKE_SCALE) >> 16; | |
1069 | intake = max(intake, (int)state->mpu.rminn_intake_fan); | |
1070 | intake = min(intake, (int)state->mpu.rmaxn_intake_fan); | |
1071 | state->intake_rpm = intake; | |
1072 | ||
1073 | do_set_fans: | |
1074 | DBG("** CPU %d RPM: %d Ex, %d In, overtemp: %d\n", | |
1075 | state->index, (int)state->rpm, intake, state->overtemp); | |
1076 | ||
1077 | /* We should check for errors, shouldn't we ? But then, what | |
1078 | * do we do once the error occurs ? For FCU notified fan | |
1079 | * failures (-EFAULT) we probably want to notify userland | |
1080 | * some way... | |
1081 | */ | |
1082 | if (state->index == 0) { | |
1083 | set_rpm_fan(CPUA_INTAKE_FAN_RPM_INDEX, intake); | |
1084 | set_rpm_fan(CPUA_EXHAUST_FAN_RPM_INDEX, state->rpm); | |
1085 | } else { | |
1086 | set_rpm_fan(CPUB_INTAKE_FAN_RPM_INDEX, intake); | |
1087 | set_rpm_fan(CPUB_EXHAUST_FAN_RPM_INDEX, state->rpm); | |
1088 | } | |
1089 | } | |
1090 | ||
1091 | static void do_monitor_cpu_rack(struct cpu_pid_state *state) | |
1092 | { | |
1093 | s32 temp, power, fan_min; | |
1094 | int rc; | |
1095 | ||
1096 | /* Read current fan status */ | |
1097 | rc = do_read_one_cpu_values(state, &temp, &power); | |
1098 | if (rc < 0) { | |
1099 | /* XXX What do we do now ? */ | |
1100 | } | |
1101 | ||
1102 | /* Check tmax, increment overtemp if we are there. At tmax+8, we go | |
1103 | * full blown immediately and try to trigger a shutdown | |
1104 | */ | |
1105 | if (temp >= ((state->mpu.tmax + 8) << 16)) { | |
1106 | printk(KERN_WARNING "Warning ! CPU %d temperature way above maximum" | |
1107 | " (%d) !\n", | |
1108 | state->index, temp >> 16); | |
f12f4d90 | 1109 | state->overtemp = CPU_MAX_OVERTEMP / 4; |
1da177e4 LT |
1110 | } else if (temp > (state->mpu.tmax << 16)) |
1111 | state->overtemp++; | |
1112 | else | |
1113 | state->overtemp = 0; | |
1114 | if (state->overtemp >= CPU_MAX_OVERTEMP) | |
1115 | critical_state = 1; | |
1116 | if (state->overtemp > 0) { | |
1117 | state->rpm = state->intake_rpm = state->mpu.rmaxn_intake_fan; | |
1118 | goto do_set_fans; | |
1119 | } | |
1120 | ||
1121 | /* Do the PID */ | |
1122 | do_cpu_pid(state, temp, power); | |
1123 | ||
1124 | /* Check clamp from dimms */ | |
1125 | fan_min = dimm_output_clamp; | |
1126 | fan_min = max(fan_min, (int)state->mpu.rminn_intake_fan); | |
1127 | ||
861fa773 BH |
1128 | DBG(" CPU min mpu = %d, min dimm = %d\n", |
1129 | state->mpu.rminn_intake_fan, dimm_output_clamp); | |
1130 | ||
1da177e4 LT |
1131 | state->rpm = max(state->rpm, (int)fan_min); |
1132 | state->rpm = min(state->rpm, (int)state->mpu.rmaxn_intake_fan); | |
1133 | state->intake_rpm = state->rpm; | |
1134 | ||
1135 | do_set_fans: | |
1136 | DBG("** CPU %d RPM: %d overtemp: %d\n", | |
1137 | state->index, (int)state->rpm, state->overtemp); | |
1138 | ||
1139 | /* We should check for errors, shouldn't we ? But then, what | |
1140 | * do we do once the error occurs ? For FCU notified fan | |
1141 | * failures (-EFAULT) we probably want to notify userland | |
1142 | * some way... | |
1143 | */ | |
1144 | if (state->index == 0) { | |
1145 | set_rpm_fan(CPU_A1_FAN_RPM_INDEX, state->rpm); | |
1146 | set_rpm_fan(CPU_A2_FAN_RPM_INDEX, state->rpm); | |
1147 | set_rpm_fan(CPU_A3_FAN_RPM_INDEX, state->rpm); | |
1148 | } else { | |
1149 | set_rpm_fan(CPU_B1_FAN_RPM_INDEX, state->rpm); | |
1150 | set_rpm_fan(CPU_B2_FAN_RPM_INDEX, state->rpm); | |
1151 | set_rpm_fan(CPU_B3_FAN_RPM_INDEX, state->rpm); | |
1152 | } | |
1153 | } | |
1154 | ||
1155 | /* | |
1156 | * Initialize the state structure for one CPU control loop | |
1157 | */ | |
1158 | static int init_cpu_state(struct cpu_pid_state *state, int index) | |
1159 | { | |
1160 | state->index = index; | |
1161 | state->first = 1; | |
1162 | state->rpm = (cpu_pid_type == CPU_PID_TYPE_RACKMAC) ? 4000 : 1000; | |
1163 | state->overtemp = 0; | |
1164 | state->adc_config = 0x00; | |
1165 | ||
1166 | ||
1167 | if (index == 0) | |
1168 | state->monitor = attach_i2c_chip(SUPPLY_MONITOR_ID, "CPU0_monitor"); | |
1169 | else if (index == 1) | |
1170 | state->monitor = attach_i2c_chip(SUPPLY_MONITORB_ID, "CPU1_monitor"); | |
1171 | if (state->monitor == NULL) | |
1172 | goto fail; | |
1173 | ||
1174 | if (read_eeprom(index, &state->mpu)) | |
1175 | goto fail; | |
1176 | ||
1177 | state->count_power = state->mpu.tguardband; | |
1178 | if (state->count_power > CPU_POWER_HISTORY_SIZE) { | |
1179 | printk(KERN_WARNING "Warning ! too many power history slots\n"); | |
1180 | state->count_power = CPU_POWER_HISTORY_SIZE; | |
1181 | } | |
1182 | DBG("CPU %d Using %d power history entries\n", index, state->count_power); | |
1183 | ||
1184 | if (index == 0) { | |
1185 | device_create_file(&of_dev->dev, &dev_attr_cpu0_temperature); | |
1186 | device_create_file(&of_dev->dev, &dev_attr_cpu0_voltage); | |
1187 | device_create_file(&of_dev->dev, &dev_attr_cpu0_current); | |
1188 | device_create_file(&of_dev->dev, &dev_attr_cpu0_exhaust_fan_rpm); | |
1189 | device_create_file(&of_dev->dev, &dev_attr_cpu0_intake_fan_rpm); | |
1190 | } else { | |
1191 | device_create_file(&of_dev->dev, &dev_attr_cpu1_temperature); | |
1192 | device_create_file(&of_dev->dev, &dev_attr_cpu1_voltage); | |
1193 | device_create_file(&of_dev->dev, &dev_attr_cpu1_current); | |
1194 | device_create_file(&of_dev->dev, &dev_attr_cpu1_exhaust_fan_rpm); | |
1195 | device_create_file(&of_dev->dev, &dev_attr_cpu1_intake_fan_rpm); | |
1196 | } | |
1197 | ||
1198 | return 0; | |
1199 | fail: | |
1200 | if (state->monitor) | |
1201 | detach_i2c_chip(state->monitor); | |
1202 | state->monitor = NULL; | |
1203 | ||
1204 | return -ENODEV; | |
1205 | } | |
1206 | ||
1207 | /* | |
1208 | * Dispose of the state data for one CPU control loop | |
1209 | */ | |
1210 | static void dispose_cpu_state(struct cpu_pid_state *state) | |
1211 | { | |
1212 | if (state->monitor == NULL) | |
1213 | return; | |
1214 | ||
1215 | if (state->index == 0) { | |
1216 | device_remove_file(&of_dev->dev, &dev_attr_cpu0_temperature); | |
1217 | device_remove_file(&of_dev->dev, &dev_attr_cpu0_voltage); | |
1218 | device_remove_file(&of_dev->dev, &dev_attr_cpu0_current); | |
1219 | device_remove_file(&of_dev->dev, &dev_attr_cpu0_exhaust_fan_rpm); | |
1220 | device_remove_file(&of_dev->dev, &dev_attr_cpu0_intake_fan_rpm); | |
1221 | } else { | |
1222 | device_remove_file(&of_dev->dev, &dev_attr_cpu1_temperature); | |
1223 | device_remove_file(&of_dev->dev, &dev_attr_cpu1_voltage); | |
1224 | device_remove_file(&of_dev->dev, &dev_attr_cpu1_current); | |
1225 | device_remove_file(&of_dev->dev, &dev_attr_cpu1_exhaust_fan_rpm); | |
1226 | device_remove_file(&of_dev->dev, &dev_attr_cpu1_intake_fan_rpm); | |
1227 | } | |
1228 | ||
1229 | detach_i2c_chip(state->monitor); | |
1230 | state->monitor = NULL; | |
1231 | } | |
1232 | ||
1233 | /* | |
1234 | * Motherboard backside & U3 heatsink fan control loop | |
1235 | */ | |
1236 | static void do_monitor_backside(struct backside_pid_state *state) | |
1237 | { | |
1238 | s32 temp, integral, derivative, fan_min; | |
1239 | s64 integ_p, deriv_p, prop_p, sum; | |
1240 | int i, rc; | |
1241 | ||
1242 | if (--state->ticks != 0) | |
1243 | return; | |
1244 | state->ticks = backside_params.interval; | |
1245 | ||
1246 | DBG("backside:\n"); | |
1247 | ||
1248 | /* Check fan status */ | |
1249 | rc = get_pwm_fan(BACKSIDE_FAN_PWM_INDEX); | |
1250 | if (rc < 0) { | |
1251 | printk(KERN_WARNING "Error %d reading backside fan !\n", rc); | |
1252 | /* XXX What do we do now ? */ | |
1253 | } else | |
1254 | state->pwm = rc; | |
1255 | DBG(" current pwm: %d\n", state->pwm); | |
1256 | ||
1257 | /* Get some sensor readings */ | |
1258 | temp = i2c_smbus_read_byte_data(state->monitor, MAX6690_EXT_TEMP) << 16; | |
1259 | state->last_temp = temp; | |
1260 | DBG(" temp: %d.%03d, target: %d.%03d\n", FIX32TOPRINT(temp), | |
1261 | FIX32TOPRINT(backside_params.input_target)); | |
1262 | ||
1263 | /* Store temperature and error in history array */ | |
1264 | state->cur_sample = (state->cur_sample + 1) % BACKSIDE_PID_HISTORY_SIZE; | |
1265 | state->sample_history[state->cur_sample] = temp; | |
1266 | state->error_history[state->cur_sample] = temp - backside_params.input_target; | |
1267 | ||
1268 | /* If first loop, fill the history table */ | |
1269 | if (state->first) { | |
1270 | for (i = 0; i < (BACKSIDE_PID_HISTORY_SIZE - 1); i++) { | |
1271 | state->cur_sample = (state->cur_sample + 1) % | |
1272 | BACKSIDE_PID_HISTORY_SIZE; | |
1273 | state->sample_history[state->cur_sample] = temp; | |
1274 | state->error_history[state->cur_sample] = | |
1275 | temp - backside_params.input_target; | |
1276 | } | |
1277 | state->first = 0; | |
1278 | } | |
1279 | ||
1280 | /* Calculate the integral term */ | |
1281 | sum = 0; | |
1282 | integral = 0; | |
1283 | for (i = 0; i < BACKSIDE_PID_HISTORY_SIZE; i++) | |
1284 | integral += state->error_history[i]; | |
1285 | integral *= backside_params.interval; | |
1286 | DBG(" integral: %08x\n", integral); | |
1287 | integ_p = ((s64)backside_params.G_r) * (s64)integral; | |
1288 | DBG(" integ_p: %d\n", (int)(integ_p >> 36)); | |
1289 | sum += integ_p; | |
1290 | ||
1291 | /* Calculate the derivative term */ | |
1292 | derivative = state->error_history[state->cur_sample] - | |
1293 | state->error_history[(state->cur_sample + BACKSIDE_PID_HISTORY_SIZE - 1) | |
1294 | % BACKSIDE_PID_HISTORY_SIZE]; | |
1295 | derivative /= backside_params.interval; | |
1296 | deriv_p = ((s64)backside_params.G_d) * (s64)derivative; | |
1297 | DBG(" deriv_p: %d\n", (int)(deriv_p >> 36)); | |
1298 | sum += deriv_p; | |
1299 | ||
1300 | /* Calculate the proportional term */ | |
1301 | prop_p = ((s64)backside_params.G_p) * (s64)(state->error_history[state->cur_sample]); | |
1302 | DBG(" prop_p: %d\n", (int)(prop_p >> 36)); | |
1303 | sum += prop_p; | |
1304 | ||
1305 | /* Scale sum */ | |
1306 | sum >>= 36; | |
1307 | ||
1308 | DBG(" sum: %d\n", (int)sum); | |
1309 | if (backside_params.additive) | |
1310 | state->pwm += (s32)sum; | |
1311 | else | |
1312 | state->pwm = sum; | |
1313 | ||
1314 | /* Check for clamp */ | |
1315 | fan_min = (dimm_output_clamp * 100) / 14000; | |
1316 | fan_min = max(fan_min, backside_params.output_min); | |
1317 | ||
1318 | state->pwm = max(state->pwm, fan_min); | |
1319 | state->pwm = min(state->pwm, backside_params.output_max); | |
1320 | ||
1321 | DBG("** BACKSIDE PWM: %d\n", (int)state->pwm); | |
1322 | set_pwm_fan(BACKSIDE_FAN_PWM_INDEX, state->pwm); | |
1323 | } | |
1324 | ||
1325 | /* | |
1326 | * Initialize the state structure for the backside fan control loop | |
1327 | */ | |
1328 | static int init_backside_state(struct backside_pid_state *state) | |
1329 | { | |
1330 | struct device_node *u3; | |
1331 | int u3h = 1; /* conservative by default */ | |
1332 | ||
1333 | /* | |
1334 | * There are different PID params for machines with U3 and machines | |
1335 | * with U3H, pick the right ones now | |
1336 | */ | |
1337 | u3 = of_find_node_by_path("/u3@0,f8000000"); | |
1338 | if (u3 != NULL) { | |
01b2726d | 1339 | const u32 *vers = of_get_property(u3, "device-rev", NULL); |
1da177e4 LT |
1340 | if (vers) |
1341 | if (((*vers) & 0x3f) < 0x34) | |
1342 | u3h = 0; | |
1343 | of_node_put(u3); | |
1344 | } | |
1345 | ||
1346 | if (rackmac) { | |
1347 | backside_params.G_d = BACKSIDE_PID_RACK_G_d; | |
1348 | backside_params.input_target = BACKSIDE_PID_RACK_INPUT_TARGET; | |
1349 | backside_params.output_min = BACKSIDE_PID_U3H_OUTPUT_MIN; | |
1350 | backside_params.interval = BACKSIDE_PID_RACK_INTERVAL; | |
1351 | backside_params.G_p = BACKSIDE_PID_RACK_G_p; | |
1352 | backside_params.G_r = BACKSIDE_PID_G_r; | |
1353 | backside_params.output_max = BACKSIDE_PID_OUTPUT_MAX; | |
1354 | backside_params.additive = 0; | |
1355 | } else if (u3h) { | |
1356 | backside_params.G_d = BACKSIDE_PID_U3H_G_d; | |
1357 | backside_params.input_target = BACKSIDE_PID_U3H_INPUT_TARGET; | |
1358 | backside_params.output_min = BACKSIDE_PID_U3H_OUTPUT_MIN; | |
1359 | backside_params.interval = BACKSIDE_PID_INTERVAL; | |
1360 | backside_params.G_p = BACKSIDE_PID_G_p; | |
1361 | backside_params.G_r = BACKSIDE_PID_G_r; | |
1362 | backside_params.output_max = BACKSIDE_PID_OUTPUT_MAX; | |
1363 | backside_params.additive = 1; | |
1364 | } else { | |
1365 | backside_params.G_d = BACKSIDE_PID_U3_G_d; | |
1366 | backside_params.input_target = BACKSIDE_PID_U3_INPUT_TARGET; | |
1367 | backside_params.output_min = BACKSIDE_PID_U3_OUTPUT_MIN; | |
1368 | backside_params.interval = BACKSIDE_PID_INTERVAL; | |
1369 | backside_params.G_p = BACKSIDE_PID_G_p; | |
1370 | backside_params.G_r = BACKSIDE_PID_G_r; | |
1371 | backside_params.output_max = BACKSIDE_PID_OUTPUT_MAX; | |
1372 | backside_params.additive = 1; | |
1373 | } | |
1374 | ||
1375 | state->ticks = 1; | |
1376 | state->first = 1; | |
1377 | state->pwm = 50; | |
1378 | ||
1379 | state->monitor = attach_i2c_chip(BACKSIDE_MAX_ID, "backside_temp"); | |
1380 | if (state->monitor == NULL) | |
1381 | return -ENODEV; | |
1382 | ||
1383 | device_create_file(&of_dev->dev, &dev_attr_backside_temperature); | |
1384 | device_create_file(&of_dev->dev, &dev_attr_backside_fan_pwm); | |
1385 | ||
1386 | return 0; | |
1387 | } | |
1388 | ||
1389 | /* | |
1390 | * Dispose of the state data for the backside control loop | |
1391 | */ | |
1392 | static void dispose_backside_state(struct backside_pid_state *state) | |
1393 | { | |
1394 | if (state->monitor == NULL) | |
1395 | return; | |
1396 | ||
1397 | device_remove_file(&of_dev->dev, &dev_attr_backside_temperature); | |
1398 | device_remove_file(&of_dev->dev, &dev_attr_backside_fan_pwm); | |
1399 | ||
1400 | detach_i2c_chip(state->monitor); | |
1401 | state->monitor = NULL; | |
1402 | } | |
1403 | ||
1404 | /* | |
1405 | * Drives bay fan control loop | |
1406 | */ | |
1407 | static void do_monitor_drives(struct drives_pid_state *state) | |
1408 | { | |
1409 | s32 temp, integral, derivative; | |
1410 | s64 integ_p, deriv_p, prop_p, sum; | |
1411 | int i, rc; | |
1412 | ||
1413 | if (--state->ticks != 0) | |
1414 | return; | |
1415 | state->ticks = DRIVES_PID_INTERVAL; | |
1416 | ||
1417 | DBG("drives:\n"); | |
1418 | ||
1419 | /* Check fan status */ | |
1420 | rc = get_rpm_fan(DRIVES_FAN_RPM_INDEX, !RPM_PID_USE_ACTUAL_SPEED); | |
1421 | if (rc < 0) { | |
1422 | printk(KERN_WARNING "Error %d reading drives fan !\n", rc); | |
1423 | /* XXX What do we do now ? */ | |
1424 | } else | |
1425 | state->rpm = rc; | |
1426 | DBG(" current rpm: %d\n", state->rpm); | |
1427 | ||
1428 | /* Get some sensor readings */ | |
861fa773 BH |
1429 | temp = le16_to_cpu(i2c_smbus_read_word_data(state->monitor, |
1430 | DS1775_TEMP)) << 8; | |
1da177e4 LT |
1431 | state->last_temp = temp; |
1432 | DBG(" temp: %d.%03d, target: %d.%03d\n", FIX32TOPRINT(temp), | |
1433 | FIX32TOPRINT(DRIVES_PID_INPUT_TARGET)); | |
1434 | ||
1435 | /* Store temperature and error in history array */ | |
1436 | state->cur_sample = (state->cur_sample + 1) % DRIVES_PID_HISTORY_SIZE; | |
1437 | state->sample_history[state->cur_sample] = temp; | |
1438 | state->error_history[state->cur_sample] = temp - DRIVES_PID_INPUT_TARGET; | |
1439 | ||
1440 | /* If first loop, fill the history table */ | |
1441 | if (state->first) { | |
1442 | for (i = 0; i < (DRIVES_PID_HISTORY_SIZE - 1); i++) { | |
1443 | state->cur_sample = (state->cur_sample + 1) % | |
1444 | DRIVES_PID_HISTORY_SIZE; | |
1445 | state->sample_history[state->cur_sample] = temp; | |
1446 | state->error_history[state->cur_sample] = | |
1447 | temp - DRIVES_PID_INPUT_TARGET; | |
1448 | } | |
1449 | state->first = 0; | |
1450 | } | |
1451 | ||
1452 | /* Calculate the integral term */ | |
1453 | sum = 0; | |
1454 | integral = 0; | |
1455 | for (i = 0; i < DRIVES_PID_HISTORY_SIZE; i++) | |
1456 | integral += state->error_history[i]; | |
1457 | integral *= DRIVES_PID_INTERVAL; | |
1458 | DBG(" integral: %08x\n", integral); | |
1459 | integ_p = ((s64)DRIVES_PID_G_r) * (s64)integral; | |
1460 | DBG(" integ_p: %d\n", (int)(integ_p >> 36)); | |
1461 | sum += integ_p; | |
1462 | ||
1463 | /* Calculate the derivative term */ | |
1464 | derivative = state->error_history[state->cur_sample] - | |
1465 | state->error_history[(state->cur_sample + DRIVES_PID_HISTORY_SIZE - 1) | |
1466 | % DRIVES_PID_HISTORY_SIZE]; | |
1467 | derivative /= DRIVES_PID_INTERVAL; | |
1468 | deriv_p = ((s64)DRIVES_PID_G_d) * (s64)derivative; | |
1469 | DBG(" deriv_p: %d\n", (int)(deriv_p >> 36)); | |
1470 | sum += deriv_p; | |
1471 | ||
1472 | /* Calculate the proportional term */ | |
1473 | prop_p = ((s64)DRIVES_PID_G_p) * (s64)(state->error_history[state->cur_sample]); | |
1474 | DBG(" prop_p: %d\n", (int)(prop_p >> 36)); | |
1475 | sum += prop_p; | |
1476 | ||
1477 | /* Scale sum */ | |
1478 | sum >>= 36; | |
1479 | ||
1480 | DBG(" sum: %d\n", (int)sum); | |
1481 | state->rpm += (s32)sum; | |
1482 | ||
1483 | state->rpm = max(state->rpm, DRIVES_PID_OUTPUT_MIN); | |
1484 | state->rpm = min(state->rpm, DRIVES_PID_OUTPUT_MAX); | |
1485 | ||
1486 | DBG("** DRIVES RPM: %d\n", (int)state->rpm); | |
1487 | set_rpm_fan(DRIVES_FAN_RPM_INDEX, state->rpm); | |
1488 | } | |
1489 | ||
1490 | /* | |
1491 | * Initialize the state structure for the drives bay fan control loop | |
1492 | */ | |
1493 | static int init_drives_state(struct drives_pid_state *state) | |
1494 | { | |
1495 | state->ticks = 1; | |
1496 | state->first = 1; | |
1497 | state->rpm = 1000; | |
1498 | ||
1499 | state->monitor = attach_i2c_chip(DRIVES_DALLAS_ID, "drives_temp"); | |
1500 | if (state->monitor == NULL) | |
1501 | return -ENODEV; | |
1502 | ||
1503 | device_create_file(&of_dev->dev, &dev_attr_drives_temperature); | |
1504 | device_create_file(&of_dev->dev, &dev_attr_drives_fan_rpm); | |
1505 | ||
1506 | return 0; | |
1507 | } | |
1508 | ||
1509 | /* | |
1510 | * Dispose of the state data for the drives control loop | |
1511 | */ | |
1512 | static void dispose_drives_state(struct drives_pid_state *state) | |
1513 | { | |
1514 | if (state->monitor == NULL) | |
1515 | return; | |
1516 | ||
1517 | device_remove_file(&of_dev->dev, &dev_attr_drives_temperature); | |
1518 | device_remove_file(&of_dev->dev, &dev_attr_drives_fan_rpm); | |
1519 | ||
1520 | detach_i2c_chip(state->monitor); | |
1521 | state->monitor = NULL; | |
1522 | } | |
1523 | ||
1524 | /* | |
1525 | * DIMMs temp control loop | |
1526 | */ | |
1527 | static void do_monitor_dimms(struct dimm_pid_state *state) | |
1528 | { | |
1529 | s32 temp, integral, derivative, fan_min; | |
1530 | s64 integ_p, deriv_p, prop_p, sum; | |
1531 | int i; | |
1532 | ||
1533 | if (--state->ticks != 0) | |
1534 | return; | |
1535 | state->ticks = DIMM_PID_INTERVAL; | |
1536 | ||
1537 | DBG("DIMM:\n"); | |
1538 | ||
1539 | DBG(" current value: %d\n", state->output); | |
1540 | ||
1541 | temp = read_lm87_reg(state->monitor, LM87_INT_TEMP); | |
1542 | if (temp < 0) | |
1543 | return; | |
1544 | temp <<= 16; | |
1545 | state->last_temp = temp; | |
1546 | DBG(" temp: %d.%03d, target: %d.%03d\n", FIX32TOPRINT(temp), | |
1547 | FIX32TOPRINT(DIMM_PID_INPUT_TARGET)); | |
1548 | ||
1549 | /* Store temperature and error in history array */ | |
1550 | state->cur_sample = (state->cur_sample + 1) % DIMM_PID_HISTORY_SIZE; | |
1551 | state->sample_history[state->cur_sample] = temp; | |
1552 | state->error_history[state->cur_sample] = temp - DIMM_PID_INPUT_TARGET; | |
1553 | ||
1554 | /* If first loop, fill the history table */ | |
1555 | if (state->first) { | |
1556 | for (i = 0; i < (DIMM_PID_HISTORY_SIZE - 1); i++) { | |
1557 | state->cur_sample = (state->cur_sample + 1) % | |
1558 | DIMM_PID_HISTORY_SIZE; | |
1559 | state->sample_history[state->cur_sample] = temp; | |
1560 | state->error_history[state->cur_sample] = | |
1561 | temp - DIMM_PID_INPUT_TARGET; | |
1562 | } | |
1563 | state->first = 0; | |
1564 | } | |
1565 | ||
1566 | /* Calculate the integral term */ | |
1567 | sum = 0; | |
1568 | integral = 0; | |
1569 | for (i = 0; i < DIMM_PID_HISTORY_SIZE; i++) | |
1570 | integral += state->error_history[i]; | |
1571 | integral *= DIMM_PID_INTERVAL; | |
1572 | DBG(" integral: %08x\n", integral); | |
1573 | integ_p = ((s64)DIMM_PID_G_r) * (s64)integral; | |
1574 | DBG(" integ_p: %d\n", (int)(integ_p >> 36)); | |
1575 | sum += integ_p; | |
1576 | ||
1577 | /* Calculate the derivative term */ | |
1578 | derivative = state->error_history[state->cur_sample] - | |
1579 | state->error_history[(state->cur_sample + DIMM_PID_HISTORY_SIZE - 1) | |
1580 | % DIMM_PID_HISTORY_SIZE]; | |
1581 | derivative /= DIMM_PID_INTERVAL; | |
1582 | deriv_p = ((s64)DIMM_PID_G_d) * (s64)derivative; | |
1583 | DBG(" deriv_p: %d\n", (int)(deriv_p >> 36)); | |
1584 | sum += deriv_p; | |
1585 | ||
1586 | /* Calculate the proportional term */ | |
1587 | prop_p = ((s64)DIMM_PID_G_p) * (s64)(state->error_history[state->cur_sample]); | |
1588 | DBG(" prop_p: %d\n", (int)(prop_p >> 36)); | |
1589 | sum += prop_p; | |
1590 | ||
1591 | /* Scale sum */ | |
1592 | sum >>= 36; | |
1593 | ||
1594 | DBG(" sum: %d\n", (int)sum); | |
1595 | state->output = (s32)sum; | |
1596 | state->output = max(state->output, DIMM_PID_OUTPUT_MIN); | |
1597 | state->output = min(state->output, DIMM_PID_OUTPUT_MAX); | |
1598 | dimm_output_clamp = state->output; | |
1599 | ||
1600 | DBG("** DIMM clamp value: %d\n", (int)state->output); | |
1601 | ||
1602 | /* Backside PID is only every 5 seconds, force backside fan clamping now */ | |
1603 | fan_min = (dimm_output_clamp * 100) / 14000; | |
1604 | fan_min = max(fan_min, backside_params.output_min); | |
1605 | if (backside_state.pwm < fan_min) { | |
1606 | backside_state.pwm = fan_min; | |
1607 | DBG(" -> applying clamp to backside fan now: %d !\n", fan_min); | |
1608 | set_pwm_fan(BACKSIDE_FAN_PWM_INDEX, fan_min); | |
1609 | } | |
1610 | } | |
1611 | ||
1612 | /* | |
1613 | * Initialize the state structure for the DIMM temp control loop | |
1614 | */ | |
1615 | static int init_dimms_state(struct dimm_pid_state *state) | |
1616 | { | |
1617 | state->ticks = 1; | |
1618 | state->first = 1; | |
1619 | state->output = 4000; | |
1620 | ||
1621 | state->monitor = attach_i2c_chip(XSERVE_DIMMS_LM87, "dimms_temp"); | |
1622 | if (state->monitor == NULL) | |
1623 | return -ENODEV; | |
1624 | ||
1625 | device_create_file(&of_dev->dev, &dev_attr_dimms_temperature); | |
1626 | ||
1627 | return 0; | |
1628 | } | |
1629 | ||
1630 | /* | |
861fa773 | 1631 | * Dispose of the state data for the DIMM control loop |
1da177e4 LT |
1632 | */ |
1633 | static void dispose_dimms_state(struct dimm_pid_state *state) | |
1634 | { | |
1635 | if (state->monitor == NULL) | |
1636 | return; | |
1637 | ||
1638 | device_remove_file(&of_dev->dev, &dev_attr_dimms_temperature); | |
1639 | ||
1640 | detach_i2c_chip(state->monitor); | |
1641 | state->monitor = NULL; | |
1642 | } | |
1643 | ||
861fa773 BH |
1644 | /* |
1645 | * Slots fan control loop | |
1646 | */ | |
1647 | static void do_monitor_slots(struct slots_pid_state *state) | |
1648 | { | |
1649 | s32 temp, integral, derivative; | |
1650 | s64 integ_p, deriv_p, prop_p, sum; | |
1651 | int i, rc; | |
1652 | ||
1653 | if (--state->ticks != 0) | |
1654 | return; | |
1655 | state->ticks = SLOTS_PID_INTERVAL; | |
1656 | ||
1657 | DBG("slots:\n"); | |
1658 | ||
1659 | /* Check fan status */ | |
1660 | rc = get_pwm_fan(SLOTS_FAN_PWM_INDEX); | |
1661 | if (rc < 0) { | |
1662 | printk(KERN_WARNING "Error %d reading slots fan !\n", rc); | |
1663 | /* XXX What do we do now ? */ | |
1664 | } else | |
1665 | state->pwm = rc; | |
1666 | DBG(" current pwm: %d\n", state->pwm); | |
1667 | ||
1668 | /* Get some sensor readings */ | |
1669 | temp = le16_to_cpu(i2c_smbus_read_word_data(state->monitor, | |
1670 | DS1775_TEMP)) << 8; | |
1671 | state->last_temp = temp; | |
1672 | DBG(" temp: %d.%03d, target: %d.%03d\n", FIX32TOPRINT(temp), | |
1673 | FIX32TOPRINT(SLOTS_PID_INPUT_TARGET)); | |
1674 | ||
1675 | /* Store temperature and error in history array */ | |
1676 | state->cur_sample = (state->cur_sample + 1) % SLOTS_PID_HISTORY_SIZE; | |
1677 | state->sample_history[state->cur_sample] = temp; | |
1678 | state->error_history[state->cur_sample] = temp - SLOTS_PID_INPUT_TARGET; | |
1679 | ||
1680 | /* If first loop, fill the history table */ | |
1681 | if (state->first) { | |
1682 | for (i = 0; i < (SLOTS_PID_HISTORY_SIZE - 1); i++) { | |
1683 | state->cur_sample = (state->cur_sample + 1) % | |
1684 | SLOTS_PID_HISTORY_SIZE; | |
1685 | state->sample_history[state->cur_sample] = temp; | |
1686 | state->error_history[state->cur_sample] = | |
1687 | temp - SLOTS_PID_INPUT_TARGET; | |
1688 | } | |
1689 | state->first = 0; | |
1690 | } | |
1691 | ||
1692 | /* Calculate the integral term */ | |
1693 | sum = 0; | |
1694 | integral = 0; | |
1695 | for (i = 0; i < SLOTS_PID_HISTORY_SIZE; i++) | |
1696 | integral += state->error_history[i]; | |
1697 | integral *= SLOTS_PID_INTERVAL; | |
1698 | DBG(" integral: %08x\n", integral); | |
1699 | integ_p = ((s64)SLOTS_PID_G_r) * (s64)integral; | |
1700 | DBG(" integ_p: %d\n", (int)(integ_p >> 36)); | |
1701 | sum += integ_p; | |
1702 | ||
1703 | /* Calculate the derivative term */ | |
1704 | derivative = state->error_history[state->cur_sample] - | |
1705 | state->error_history[(state->cur_sample + SLOTS_PID_HISTORY_SIZE - 1) | |
1706 | % SLOTS_PID_HISTORY_SIZE]; | |
1707 | derivative /= SLOTS_PID_INTERVAL; | |
1708 | deriv_p = ((s64)SLOTS_PID_G_d) * (s64)derivative; | |
1709 | DBG(" deriv_p: %d\n", (int)(deriv_p >> 36)); | |
1710 | sum += deriv_p; | |
1711 | ||
1712 | /* Calculate the proportional term */ | |
1713 | prop_p = ((s64)SLOTS_PID_G_p) * (s64)(state->error_history[state->cur_sample]); | |
1714 | DBG(" prop_p: %d\n", (int)(prop_p >> 36)); | |
1715 | sum += prop_p; | |
1716 | ||
1717 | /* Scale sum */ | |
1718 | sum >>= 36; | |
1719 | ||
1720 | DBG(" sum: %d\n", (int)sum); | |
1721 | state->pwm = (s32)sum; | |
1722 | ||
1723 | state->pwm = max(state->pwm, SLOTS_PID_OUTPUT_MIN); | |
1724 | state->pwm = min(state->pwm, SLOTS_PID_OUTPUT_MAX); | |
1725 | ||
1726 | DBG("** DRIVES PWM: %d\n", (int)state->pwm); | |
1727 | set_pwm_fan(SLOTS_FAN_PWM_INDEX, state->pwm); | |
1728 | } | |
1729 | ||
1730 | /* | |
1731 | * Initialize the state structure for the slots bay fan control loop | |
1732 | */ | |
1733 | static int init_slots_state(struct slots_pid_state *state) | |
1734 | { | |
1735 | state->ticks = 1; | |
1736 | state->first = 1; | |
1737 | state->pwm = 50; | |
1738 | ||
1739 | state->monitor = attach_i2c_chip(XSERVE_SLOTS_LM75, "slots_temp"); | |
1740 | if (state->monitor == NULL) | |
1741 | return -ENODEV; | |
1742 | ||
1743 | device_create_file(&of_dev->dev, &dev_attr_slots_temperature); | |
1744 | device_create_file(&of_dev->dev, &dev_attr_slots_fan_pwm); | |
1745 | ||
1746 | return 0; | |
1747 | } | |
1748 | ||
1749 | /* | |
1750 | * Dispose of the state data for the slots control loop | |
1751 | */ | |
1752 | static void dispose_slots_state(struct slots_pid_state *state) | |
1753 | { | |
1754 | if (state->monitor == NULL) | |
1755 | return; | |
1756 | ||
1757 | device_remove_file(&of_dev->dev, &dev_attr_slots_temperature); | |
1758 | device_remove_file(&of_dev->dev, &dev_attr_slots_fan_pwm); | |
1759 | ||
1760 | detach_i2c_chip(state->monitor); | |
1761 | state->monitor = NULL; | |
1762 | } | |
1763 | ||
1764 | ||
1da177e4 LT |
1765 | static int call_critical_overtemp(void) |
1766 | { | |
1767 | char *argv[] = { critical_overtemp_path, NULL }; | |
1768 | static char *envp[] = { "HOME=/", | |
1769 | "TERM=linux", | |
1770 | "PATH=/sbin:/usr/sbin:/bin:/usr/bin", | |
1771 | NULL }; | |
1772 | ||
1773 | return call_usermodehelper(critical_overtemp_path, argv, envp, 0); | |
1774 | } | |
1775 | ||
1776 | ||
1777 | /* | |
1778 | * Here's the kernel thread that calls the various control loops | |
1779 | */ | |
1780 | static int main_control_loop(void *x) | |
1781 | { | |
1782 | daemonize("kfand"); | |
1783 | ||
1784 | DBG("main_control_loop started\n"); | |
1785 | ||
1786 | down(&driver_lock); | |
1787 | ||
1788 | if (start_fcu() < 0) { | |
1789 | printk(KERN_ERR "kfand: failed to start FCU\n"); | |
1790 | up(&driver_lock); | |
1791 | goto out; | |
1792 | } | |
1793 | ||
861fa773 BH |
1794 | /* Set the PCI fan once for now on non-RackMac */ |
1795 | if (!rackmac) | |
1796 | set_pwm_fan(SLOTS_FAN_PWM_INDEX, SLOTS_FAN_DEFAULT_PWM); | |
1da177e4 LT |
1797 | |
1798 | /* Initialize ADCs */ | |
1799 | initialize_adc(&cpu_state[0]); | |
1800 | if (cpu_state[1].monitor != NULL) | |
1801 | initialize_adc(&cpu_state[1]); | |
1802 | ||
861fa773 BH |
1803 | fcu_tickle_ticks = FCU_TICKLE_TICKS; |
1804 | ||
1da177e4 LT |
1805 | up(&driver_lock); |
1806 | ||
1807 | while (state == state_attached) { | |
1808 | unsigned long elapsed, start; | |
1809 | ||
1810 | start = jiffies; | |
1811 | ||
1812 | down(&driver_lock); | |
1813 | ||
861fa773 BH |
1814 | /* Tickle the FCU just in case */ |
1815 | if (--fcu_tickle_ticks < 0) { | |
1816 | fcu_tickle_ticks = FCU_TICKLE_TICKS; | |
1817 | tickle_fcu(); | |
1818 | } | |
1819 | ||
1da177e4 LT |
1820 | /* First, we always calculate the new DIMMs state on an Xserve */ |
1821 | if (rackmac) | |
1822 | do_monitor_dimms(&dimms_state); | |
1823 | ||
1824 | /* Then, the CPUs */ | |
1825 | if (cpu_pid_type == CPU_PID_TYPE_COMBINED) | |
1826 | do_monitor_cpu_combined(); | |
1827 | else if (cpu_pid_type == CPU_PID_TYPE_RACKMAC) { | |
1828 | do_monitor_cpu_rack(&cpu_state[0]); | |
1829 | if (cpu_state[1].monitor != NULL) | |
1830 | do_monitor_cpu_rack(&cpu_state[1]); | |
1831 | // better deal with UP | |
1832 | } else { | |
1833 | do_monitor_cpu_split(&cpu_state[0]); | |
1834 | if (cpu_state[1].monitor != NULL) | |
1835 | do_monitor_cpu_split(&cpu_state[1]); | |
1836 | // better deal with UP | |
1837 | } | |
1838 | /* Then, the rest */ | |
1839 | do_monitor_backside(&backside_state); | |
861fa773 BH |
1840 | if (rackmac) |
1841 | do_monitor_slots(&slots_state); | |
1842 | else | |
1da177e4 LT |
1843 | do_monitor_drives(&drives_state); |
1844 | up(&driver_lock); | |
1845 | ||
1846 | if (critical_state == 1) { | |
1847 | printk(KERN_WARNING "Temperature control detected a critical condition\n"); | |
1848 | printk(KERN_WARNING "Attempting to shut down...\n"); | |
1849 | if (call_critical_overtemp()) { | |
1850 | printk(KERN_WARNING "Can't call %s, power off now!\n", | |
1851 | critical_overtemp_path); | |
1852 | machine_power_off(); | |
1853 | } | |
1854 | } | |
1855 | if (critical_state > 0) | |
1856 | critical_state++; | |
1857 | if (critical_state > MAX_CRITICAL_STATE) { | |
1858 | printk(KERN_WARNING "Shutdown timed out, power off now !\n"); | |
1859 | machine_power_off(); | |
1860 | } | |
1861 | ||
1862 | // FIXME: Deal with signals | |
1da177e4 LT |
1863 | elapsed = jiffies - start; |
1864 | if (elapsed < HZ) | |
12621a16 | 1865 | schedule_timeout_interruptible(HZ - elapsed); |
1da177e4 LT |
1866 | } |
1867 | ||
1868 | out: | |
1869 | DBG("main_control_loop ended\n"); | |
1870 | ||
1871 | ctrl_task = 0; | |
1872 | complete_and_exit(&ctrl_complete, 0); | |
1873 | } | |
1874 | ||
1875 | /* | |
1876 | * Dispose the control loops when tearing down | |
1877 | */ | |
1878 | static void dispose_control_loops(void) | |
1879 | { | |
1880 | dispose_cpu_state(&cpu_state[0]); | |
1881 | dispose_cpu_state(&cpu_state[1]); | |
1882 | dispose_backside_state(&backside_state); | |
1883 | dispose_drives_state(&drives_state); | |
861fa773 | 1884 | dispose_slots_state(&slots_state); |
1da177e4 LT |
1885 | dispose_dimms_state(&dimms_state); |
1886 | } | |
1887 | ||
1888 | /* | |
1889 | * Create the control loops. U3-0 i2c bus is up, so we can now | |
1890 | * get to the various sensors | |
1891 | */ | |
1892 | static int create_control_loops(void) | |
1893 | { | |
1894 | struct device_node *np; | |
1895 | ||
1896 | /* Count CPUs from the device-tree, we don't care how many are | |
1897 | * actually used by Linux | |
1898 | */ | |
1899 | cpu_count = 0; | |
1900 | for (np = NULL; NULL != (np = of_find_node_by_type(np, "cpu"));) | |
1901 | cpu_count++; | |
1902 | ||
1903 | DBG("counted %d CPUs in the device-tree\n", cpu_count); | |
1904 | ||
1905 | /* Decide the type of PID algorithm to use based on the presence of | |
1906 | * the pumps, though that may not be the best way, that is good enough | |
1907 | * for now | |
1908 | */ | |
1909 | if (rackmac) | |
1910 | cpu_pid_type = CPU_PID_TYPE_RACKMAC; | |
1911 | else if (machine_is_compatible("PowerMac7,3") | |
1912 | && (cpu_count > 1) | |
1913 | && fcu_fans[CPUA_PUMP_RPM_INDEX].id != FCU_FAN_ABSENT_ID | |
1914 | && fcu_fans[CPUB_PUMP_RPM_INDEX].id != FCU_FAN_ABSENT_ID) { | |
1915 | printk(KERN_INFO "Liquid cooling pumps detected, using new algorithm !\n"); | |
1916 | cpu_pid_type = CPU_PID_TYPE_COMBINED; | |
1917 | } else | |
1918 | cpu_pid_type = CPU_PID_TYPE_SPLIT; | |
1919 | ||
1920 | /* Create control loops for everything. If any fail, everything | |
1921 | * fails | |
1922 | */ | |
1923 | if (init_cpu_state(&cpu_state[0], 0)) | |
1924 | goto fail; | |
1925 | if (cpu_pid_type == CPU_PID_TYPE_COMBINED) | |
1926 | fetch_cpu_pumps_minmax(); | |
1927 | ||
1928 | if (cpu_count > 1 && init_cpu_state(&cpu_state[1], 1)) | |
1929 | goto fail; | |
1930 | if (init_backside_state(&backside_state)) | |
1931 | goto fail; | |
1932 | if (rackmac && init_dimms_state(&dimms_state)) | |
1933 | goto fail; | |
861fa773 BH |
1934 | if (rackmac && init_slots_state(&slots_state)) |
1935 | goto fail; | |
1da177e4 LT |
1936 | if (!rackmac && init_drives_state(&drives_state)) |
1937 | goto fail; | |
1938 | ||
1939 | DBG("all control loops up !\n"); | |
1940 | ||
1941 | return 0; | |
1942 | ||
1943 | fail: | |
1944 | DBG("failure creating control loops, disposing\n"); | |
1945 | ||
1946 | dispose_control_loops(); | |
1947 | ||
1948 | return -ENODEV; | |
1949 | } | |
1950 | ||
1951 | /* | |
1952 | * Start the control loops after everything is up, that is create | |
1953 | * the thread that will make them run | |
1954 | */ | |
1955 | static void start_control_loops(void) | |
1956 | { | |
1957 | init_completion(&ctrl_complete); | |
1958 | ||
1959 | ctrl_task = kernel_thread(main_control_loop, NULL, SIGCHLD | CLONE_KERNEL); | |
1960 | } | |
1961 | ||
1962 | /* | |
1963 | * Stop the control loops when tearing down | |
1964 | */ | |
1965 | static void stop_control_loops(void) | |
1966 | { | |
1967 | if (ctrl_task != 0) | |
1968 | wait_for_completion(&ctrl_complete); | |
1969 | } | |
1970 | ||
1971 | /* | |
1972 | * Attach to the i2c FCU after detecting U3-1 bus | |
1973 | */ | |
1974 | static int attach_fcu(void) | |
1975 | { | |
1976 | fcu = attach_i2c_chip(FAN_CTRLER_ID, "fcu"); | |
1977 | if (fcu == NULL) | |
1978 | return -ENODEV; | |
1979 | ||
1980 | DBG("FCU attached\n"); | |
1981 | ||
1982 | return 0; | |
1983 | } | |
1984 | ||
1985 | /* | |
1986 | * Detach from the i2c FCU when tearing down | |
1987 | */ | |
1988 | static void detach_fcu(void) | |
1989 | { | |
1990 | if (fcu) | |
1991 | detach_i2c_chip(fcu); | |
1992 | fcu = NULL; | |
1993 | } | |
1994 | ||
1995 | /* | |
1996 | * Attach to the i2c controller. We probe the various chips based | |
1997 | * on the device-tree nodes and build everything for the driver to | |
1998 | * run, we then kick the driver monitoring thread | |
1999 | */ | |
2000 | static int therm_pm72_attach(struct i2c_adapter *adapter) | |
2001 | { | |
2002 | down(&driver_lock); | |
2003 | ||
2004 | /* Check state */ | |
2005 | if (state == state_detached) | |
2006 | state = state_attaching; | |
2007 | if (state != state_attaching) { | |
2008 | up(&driver_lock); | |
2009 | return 0; | |
2010 | } | |
2011 | ||
2012 | /* Check if we are looking for one of these */ | |
2013 | if (u3_0 == NULL && !strcmp(adapter->name, "u3 0")) { | |
2014 | u3_0 = adapter; | |
2015 | DBG("found U3-0\n"); | |
2016 | if (k2 || !rackmac) | |
2017 | if (create_control_loops()) | |
2018 | u3_0 = NULL; | |
2019 | } else if (u3_1 == NULL && !strcmp(adapter->name, "u3 1")) { | |
2020 | u3_1 = adapter; | |
2021 | DBG("found U3-1, attaching FCU\n"); | |
2022 | if (attach_fcu()) | |
2023 | u3_1 = NULL; | |
2024 | } else if (k2 == NULL && !strcmp(adapter->name, "mac-io 0")) { | |
2025 | k2 = adapter; | |
2026 | DBG("Found K2\n"); | |
2027 | if (u3_0 && rackmac) | |
2028 | if (create_control_loops()) | |
2029 | k2 = NULL; | |
2030 | } | |
2031 | /* We got all we need, start control loops */ | |
2032 | if (u3_0 != NULL && u3_1 != NULL && (k2 || !rackmac)) { | |
2033 | DBG("everything up, starting control loops\n"); | |
2034 | state = state_attached; | |
2035 | start_control_loops(); | |
2036 | } | |
2037 | up(&driver_lock); | |
2038 | ||
2039 | return 0; | |
2040 | } | |
2041 | ||
2042 | /* | |
2043 | * Called on every adapter when the driver or the i2c controller | |
2044 | * is going away. | |
2045 | */ | |
2046 | static int therm_pm72_detach(struct i2c_adapter *adapter) | |
2047 | { | |
2048 | down(&driver_lock); | |
2049 | ||
2050 | if (state != state_detached) | |
2051 | state = state_detaching; | |
2052 | ||
2053 | /* Stop control loops if any */ | |
2054 | DBG("stopping control loops\n"); | |
2055 | up(&driver_lock); | |
2056 | stop_control_loops(); | |
2057 | down(&driver_lock); | |
2058 | ||
2059 | if (u3_0 != NULL && !strcmp(adapter->name, "u3 0")) { | |
2060 | DBG("lost U3-0, disposing control loops\n"); | |
2061 | dispose_control_loops(); | |
2062 | u3_0 = NULL; | |
2063 | } | |
2064 | ||
2065 | if (u3_1 != NULL && !strcmp(adapter->name, "u3 1")) { | |
2066 | DBG("lost U3-1, detaching FCU\n"); | |
2067 | detach_fcu(); | |
2068 | u3_1 = NULL; | |
2069 | } | |
2070 | if (u3_0 == NULL && u3_1 == NULL) | |
2071 | state = state_detached; | |
2072 | ||
2073 | up(&driver_lock); | |
2074 | ||
2075 | return 0; | |
2076 | } | |
2077 | ||
2078 | static int fan_check_loc_match(const char *loc, int fan) | |
2079 | { | |
2080 | char tmp[64]; | |
2081 | char *c, *e; | |
2082 | ||
2083 | strlcpy(tmp, fcu_fans[fan].loc, 64); | |
2084 | ||
2085 | c = tmp; | |
2086 | for (;;) { | |
2087 | e = strchr(c, ','); | |
2088 | if (e) | |
2089 | *e = 0; | |
2090 | if (strcmp(loc, c) == 0) | |
2091 | return 1; | |
2092 | if (e == NULL) | |
2093 | break; | |
2094 | c = e + 1; | |
2095 | } | |
2096 | return 0; | |
2097 | } | |
2098 | ||
2099 | static void fcu_lookup_fans(struct device_node *fcu_node) | |
2100 | { | |
2101 | struct device_node *np = NULL; | |
2102 | int i; | |
2103 | ||
2104 | /* The table is filled by default with values that are suitable | |
2105 | * for the old machines without device-tree informations. We scan | |
2106 | * the device-tree and override those values with whatever is | |
2107 | * there | |
2108 | */ | |
2109 | ||
2110 | DBG("Looking up FCU controls in device-tree...\n"); | |
2111 | ||
2112 | while ((np = of_get_next_child(fcu_node, np)) != NULL) { | |
2113 | int type = -1; | |
018a3d1d JK |
2114 | const char *loc; |
2115 | const u32 *reg; | |
1da177e4 LT |
2116 | |
2117 | DBG(" control: %s, type: %s\n", np->name, np->type); | |
2118 | ||
2119 | /* Detect control type */ | |
2120 | if (!strcmp(np->type, "fan-rpm-control") || | |
2121 | !strcmp(np->type, "fan-rpm")) | |
2122 | type = FCU_FAN_RPM; | |
2123 | if (!strcmp(np->type, "fan-pwm-control") || | |
2124 | !strcmp(np->type, "fan-pwm")) | |
2125 | type = FCU_FAN_PWM; | |
2126 | /* Only care about fans for now */ | |
2127 | if (type == -1) | |
2128 | continue; | |
2129 | ||
2130 | /* Lookup for a matching location */ | |
01b2726d SR |
2131 | loc = of_get_property(np, "location", NULL); |
2132 | reg = of_get_property(np, "reg", NULL); | |
1da177e4 LT |
2133 | if (loc == NULL || reg == NULL) |
2134 | continue; | |
2135 | DBG(" matching location: %s, reg: 0x%08x\n", loc, *reg); | |
2136 | ||
2137 | for (i = 0; i < FCU_FAN_COUNT; i++) { | |
2138 | int fan_id; | |
2139 | ||
2140 | if (!fan_check_loc_match(loc, i)) | |
2141 | continue; | |
2142 | DBG(" location match, index: %d\n", i); | |
2143 | fcu_fans[i].id = FCU_FAN_ABSENT_ID; | |
2144 | if (type != fcu_fans[i].type) { | |
2145 | printk(KERN_WARNING "therm_pm72: Fan type mismatch " | |
2146 | "in device-tree for %s\n", np->full_name); | |
2147 | break; | |
2148 | } | |
2149 | if (type == FCU_FAN_RPM) | |
2150 | fan_id = ((*reg) - 0x10) / 2; | |
2151 | else | |
2152 | fan_id = ((*reg) - 0x30) / 2; | |
2153 | if (fan_id > 7) { | |
2154 | printk(KERN_WARNING "therm_pm72: Can't parse " | |
2155 | "fan ID in device-tree for %s\n", np->full_name); | |
2156 | break; | |
2157 | } | |
2158 | DBG(" fan id -> %d, type -> %d\n", fan_id, type); | |
2159 | fcu_fans[i].id = fan_id; | |
2160 | } | |
2161 | } | |
2162 | ||
2163 | /* Now dump the array */ | |
2164 | printk(KERN_INFO "Detected fan controls:\n"); | |
2165 | for (i = 0; i < FCU_FAN_COUNT; i++) { | |
2166 | if (fcu_fans[i].id == FCU_FAN_ABSENT_ID) | |
2167 | continue; | |
2168 | printk(KERN_INFO " %d: %s fan, id %d, location: %s\n", i, | |
2169 | fcu_fans[i].type == FCU_FAN_RPM ? "RPM" : "PWM", | |
2170 | fcu_fans[i].id, fcu_fans[i].loc); | |
2171 | } | |
2172 | } | |
2173 | ||
5e655772 | 2174 | static int fcu_of_probe(struct of_device* dev, const struct of_device_id *match) |
1da177e4 | 2175 | { |
1da177e4 LT |
2176 | state = state_detached; |
2177 | ||
2178 | /* Lookup the fans in the device tree */ | |
2179 | fcu_lookup_fans(dev->node); | |
2180 | ||
2181 | /* Add the driver */ | |
c9662b4b | 2182 | return i2c_add_driver(&therm_pm72_driver); |
1da177e4 LT |
2183 | } |
2184 | ||
2185 | static int fcu_of_remove(struct of_device* dev) | |
2186 | { | |
2187 | i2c_del_driver(&therm_pm72_driver); | |
2188 | ||
2189 | return 0; | |
2190 | } | |
2191 | ||
5e655772 | 2192 | static struct of_device_id fcu_match[] = |
1da177e4 LT |
2193 | { |
2194 | { | |
1da177e4 | 2195 | .type = "fcu", |
1da177e4 LT |
2196 | }, |
2197 | {}, | |
2198 | }; | |
2199 | ||
2200 | static struct of_platform_driver fcu_of_platform_driver = | |
2201 | { | |
2202 | .name = "temperature", | |
5e655772 | 2203 | .match_table = fcu_match, |
1da177e4 LT |
2204 | .probe = fcu_of_probe, |
2205 | .remove = fcu_of_remove | |
2206 | }; | |
2207 | ||
2208 | /* | |
2209 | * Check machine type, attach to i2c controller | |
2210 | */ | |
2211 | static int __init therm_pm72_init(void) | |
2212 | { | |
2213 | struct device_node *np; | |
2214 | ||
2215 | rackmac = machine_is_compatible("RackMac3,1"); | |
2216 | ||
2217 | if (!machine_is_compatible("PowerMac7,2") && | |
2218 | !machine_is_compatible("PowerMac7,3") && | |
2219 | !rackmac) | |
2220 | return -ENODEV; | |
2221 | ||
2222 | printk(KERN_INFO "PowerMac G5 Thermal control driver %s\n", VERSION); | |
2223 | ||
2224 | np = of_find_node_by_type(NULL, "fcu"); | |
2225 | if (np == NULL) { | |
2226 | /* Some machines have strangely broken device-tree */ | |
2227 | np = of_find_node_by_path("/u3@0,f8000000/i2c@f8001000/fan@15e"); | |
2228 | if (np == NULL) { | |
2229 | printk(KERN_ERR "Can't find FCU in device-tree !\n"); | |
2230 | return -ENODEV; | |
2231 | } | |
2232 | } | |
0365ba7f | 2233 | of_dev = of_platform_device_create(np, "temperature", NULL); |
1da177e4 LT |
2234 | if (of_dev == NULL) { |
2235 | printk(KERN_ERR "Can't register FCU platform device !\n"); | |
2236 | return -ENODEV; | |
2237 | } | |
2238 | ||
7eebde70 | 2239 | of_register_platform_driver(&fcu_of_platform_driver); |
1da177e4 LT |
2240 | |
2241 | return 0; | |
2242 | } | |
2243 | ||
2244 | static void __exit therm_pm72_exit(void) | |
2245 | { | |
7eebde70 | 2246 | of_unregister_platform_driver(&fcu_of_platform_driver); |
1da177e4 LT |
2247 | |
2248 | if (of_dev) | |
2249 | of_device_unregister(of_dev); | |
2250 | } | |
2251 | ||
2252 | module_init(therm_pm72_init); | |
2253 | module_exit(therm_pm72_exit); | |
2254 | ||
2255 | MODULE_AUTHOR("Benjamin Herrenschmidt <benh@kernel.crashing.org>"); | |
2256 | MODULE_DESCRIPTION("Driver for Apple's PowerMac G5 thermal control"); | |
2257 | MODULE_LICENSE("GPL"); | |
2258 |