Adrian Hunter [Tue, 16 Aug 2016 10:44:12 +0000 (13:44 +0300)]
mmc: mmc_test: Add tests for sending commands during transfer
Add 6 tests for sending commands during transfer. The tests are:
* Commands during read - no Set Block Count (CMD23).
* Commands during write - no Set Block Count (CMD23).
* Commands during read - use Set Block Count (CMD23).
* Commands during write - use Set Block Count (CMD23).
* Commands during non-blocking read - use Set Block Count (CMD23).
* Commands during non-blocking write - use Set Block Count (CMD23).
For a range of transfer sizes, the tests start an ongoing data transfer and
then repeatedly send the status command (CMD13) while the transfer
continues. The tests pass if all requests complete with no errors. The host
controller driver must support MMC_CAP_CMD_DURING_TFR.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Adrian Hunter [Tue, 16 Aug 2016 10:44:11 +0000 (13:44 +0300)]
mmc: core: Add support for sending commands during data transfer
A host controller driver exposes its capability using caps flag
MMC_CAP_CMD_DURING_TFR. A driver with that capability can accept requests
that are marked mrq->cap_cmd_during_tfr = true. Then the driver informs the
upper layers when the command line is available for further commands by
calling mmc_command_done(). Because of that, the driver will not then
automatically send STOP commands, and it is the responsibility of the upper
layer to send a STOP command if it is required.
For requests submitted through the mmc_wait_for_req() interface, the caller
sets mrq->cap_cmd_during_tfr = true which causes mmc_wait_for_req() in fact
not to wait. The caller can then send commands that do not use the data
lines. Finally the caller can wait for the transfer to complete by calling
mmc_wait_for_req_done() which is now exported.
For requests submitted through the mmc_start_req() interface, the caller
again sets mrq->cap_cmd_during_tfr = true, but mmc_start_req() anyway does
not wait. The caller can then send commands that do not use the data
lines. Finally the caller can wait for the transfer to complete in the
normal way i.e. calling mmc_start_req() again.
Irrespective of how a cap_cmd_during_tfr request is started,
mmc_is_req_done() can be called if the upper layer needs to determine if
the request is done. However the appropriate waiting function (either
mmc_wait_for_req_done() or mmc_start_req()) must still be called.
The implementation consists primarily of a new completion
mrq->cmd_completion which notifies when the command line is available for
further commands. That completion is completed by mmc_command_done().
When there is an ongoing data transfer, calls to mmc_wait_for_req() will
automatically wait on that completion, so the caller does not have to do
anything special.
Note, in the case of errors, the driver may call mmc_request_done() without
calling mmc_command_done() because mmc_request_done() always calls
mmc_command_done().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jaedon Shin [Fri, 9 Sep 2016 02:08:40 +0000 (11:08 +0900)]
mmc: sdhci-brcmstb: Fix incorrect capability
Clear incorrect SDHCI_CAN_64BIT capability on Broadcom MIPS based SoCs.
The MIPS based SoCs are using ADMA only, but the several SoCs have the
incorrect capability bit about ADMA 64-bit. The "brcm,bcm7425-sdhci" is
compatible string for MIPS based SoC.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jaedon Shin [Fri, 9 Sep 2016 02:08:39 +0000 (11:08 +0900)]
mmc: DT: sdhci-brcmstb: Bindings document for common sdhci-brcmstb
Changes to the DT binding document to separate the BCM7425 and the
BCM7445.
A compatible string "brcm,bcm7425-sdhci" was representing the BCM7425
SDHCI host controller with all BRCMSTB SoCs including the BCM7445. Now
it should be separated because vary a bit in initialize each host
controller.
- Renames the DT binding document to common name.
- Adds a compatible string "brcm,bcm7445-sdhci" that is representing the
BCM7445 with thereafter 28nm generation ARM based SoCs.
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Icenowy Zheng [Fri, 5 Aug 2016 02:57:15 +0000 (04:57 +0200)]
mmc: sunxi: add support for A64 mmc controller
A64 SoC features a MMC controller which need only the mod clock, and can
calibrate delay by itself. This patch adds support for the new MMC
controller IP core.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Icenowy Zheng [Fri, 5 Aug 2016 02:57:14 +0000 (04:57 +0200)]
Documentation: dt: Add new compatible to sunxi mmc driver bindings
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Baolin Wang [Wed, 7 Sep 2016 02:38:25 +0000 (10:38 +0800)]
mmc: core: Optimize the mmc erase size alignment
In most cases the 'card->erase_size' is power of 2, then the round_up/down()
function is more efficient than '%' operation when the 'card->erase_size' is
power of 2.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Baolin Wang [Wed, 7 Sep 2016 02:38:24 +0000 (10:38 +0800)]
mmc: core: Factor out the alignment of erase size
In order to clean up the mmc_erase() function and do some optimization
for erase size alignment, factor out the guts of erase size alignment
into mmc_align_erase_size() function.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Arnd Bergmann [Tue, 6 Sep 2016 12:56:09 +0000 (14:56 +0200)]
mmc: davinci: remove incorrect NO_IRQ use
platform_get_irq() returns an error value on failure, not NO_IRQ,
so the error handling here could never work.
This changes the code to propagate the error value instead.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ai Kyuse [Tue, 6 Sep 2016 10:38:38 +0000 (12:38 +0200)]
mmc: sh_mobile_sdhi: Add r8a7796 support
Add support for r8a7796 SoC.
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Tue, 26 Jul 2016 22:04:03 +0000 (00:04 +0200)]
mmc: core: Use a default maximum erase timeout
In cases when the host->max_busy_timeout isn't specified, the calculated
number of maximum discard sectors defaults to UINT_MAX. This may cause a
too long timeout for a discard request.
Avoid this by using a default maximum erase timeout of 60s, used when we
calculate the maximum number of sectors that are allowed to be discarded
per request.
Do note that the minimum number of sectors to be discarded is still at
least one "preferred erase size".
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Thierry Reding [Thu, 1 Sep 2016 11:46:17 +0000 (13:46 +0200)]
mmc: tegra: Mark 64-bit DMA broken on Tegra124
According to the TRM, the SD/MMC controller on Tegra124 supports 34-bit
addressing, but testing shows that this doesn't work. On a device which
has more than 2 GiB of RAM and LPAE enabled, buffer allocations can use
addresses above the 32-bit boundary.
One way to work around this would be to enable IOMMU physical to virtual
address translations for the SD/MMC controllers, but that's not easy to
implement without breaking existing use-cases. It's also not obvious why
34-bit addressing doesn't work as advertised. In order to fix this for
existing users, add the SDHCI_QUIRK2_BROKEN_64_BIT_DMA quirk for now.
Reported-by: Paul Kocialkowski <contact@paulk.fr>
Acked-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Shawn Lin [Fri, 26 Aug 2016 08:51:15 +0000 (16:51 +0800)]
mmc: sdhci-of-arasan: Properly set corecfg_clockmultiplier on rk3399
corecfg_clockmultiplier indicates clock multiplier value of
programmable clock generator which should be the same value
of SDHCI_CAPABILITIES_1. The default value of the register,
corecfg_clockmultiplier, is 0x10. But actually it is a mistake
by designer as our intention was to set it to be zero which
means we don't support programmable clock generator. So we have
to make it to be zero on bootloader which seems work fine until
now. But now we find an issue that when deploying genpd support
for it, the remove callback will trigger the genpd to poweroff the
power domain for sdhci-of-arasan which manage the controller, phy
and corecfg_* stuff.
So when we do bind/unbind the driver, we have already reinit
the controller and phy, but without doing that for corecfg_*.
Regarding to only the corecfg_clockmultipler is wrong, let's
fix it by explicitly marking it to be zero when probing. With
this change, we could do bind/unbind successfully.
Reported-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Cc: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Tested-by: Ziyuan Xu <xzy.xu@rock-chips.com>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Andy Shevchenko [Mon, 29 Aug 2016 09:33:41 +0000 (12:33 +0300)]
sdhci-pci: enable SD card interface on Merrifield
Intel Merrifield provides an interface to an external SD card.
Enable it here.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Andy Shevchenko [Mon, 29 Aug 2016 09:33:40 +0000 (12:33 +0300)]
sdhci-pci: enable SDIO interface on Intel Merrifield
Intel Merrifield is known to have an SDIO interface and on Intel Edison board a
WiFi card is wired to it.
Enable the interface here to allow WiFi card enumeration.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Andy Shevchenko [Mon, 29 Aug 2016 09:33:39 +0000 (12:33 +0300)]
sdhci-pci: refactor intel_mrfld_mmc_probe_slot()
Refactor intel_mrfld_mmc_probe_slot() to use switch case. The change allows to
add a support for SD and SDIO interfaces without any pain.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jin Guojun [Thu, 4 Aug 2016 02:16:13 +0000 (10:16 +0800)]
mmc: dw_mmc: k3: UHS-SD card for Hisilicon Hikey
Hisilicon Hikey have no tuning function in dw_mmc-k3.c,
so we must do the tuning function stub when we init UHS card.
Signed-off-by: Jin Guojun <kid.jin@hisilicon.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Shawn Lin [Mon, 22 Aug 2016 02:57:16 +0000 (10:57 +0800)]
mmc: dw_mmc: return -EILSEQ for EBE and SBE error
The following log we found indicate the fact that dw_mmc
didn't treat EBE or SBE as a similar problem as CRC error.
-EIO is quite not informative as it may indicate that the device
is broken rather than that of tuning stuff.
...
[ 89.057226] bcmsdh_sdmmc: Failed to Read byte F1:@0x1001f=ff, Err: -5
[ 89.058811] bcmsdh_sdmmc: Failed to Read byte F1:@0x1001f=ff, Err: -5
[ 89.059415] bcmsdh_sdmmc: Failed to Read byte F1:@0x1000e=ff, Err: -84
[ 89.254248] dwmmc_rockchip
fe310000.dwmmc: Successfully tuned phase to 199
[ 89.273912] dhd_set_suspend: Remove extra suspend setting
[ 89.274478] dhd_enable_packet_filter: enter, value = 0
64 bytes from 112.90.83.112: icmp_seq=24 ttl=53 time=1321 ms
64 bytes from 112.90.83.112: icmp_seq=25 ttl=53 time=319 ms
64 bytes from 112.90.83.112: icmp_seq=26 ttl=53 time=69.8 ms
64 bytes from 112.90.83.112: icmp_seq=27 ttl=53 time=37.5 ms
...
For the host, when failing to sample cmd's response due to
tuning stuff, we still return -EIO as it's quite vague to figure
out whether it related to signal or just the broken devices, especially
for the card type detection when booting kernel as all things go well
but the cmd set used.
But for the data phase, if receiving the cmd's response which
carriess data transfer, we should have more confidence that it
is very probably related to the tuning stuff.
Just as the log shown above, we sometimes suffer too much
this kind of pain as the dw_mmc return -EIO for the case, so
mmc-core will not do retune and caller drivers like bcm's wifi
driver, still retry the failure more and more until dw_mmc
finally generate CRC.
Adrian suggested that drivers who care the specific cases should
call mmc_retune_needed rather than doing it in mmc core. It makes
sense but I'm considering that -EILSEQ actually means illegal sequence
, so we use it for CRC cases. Meanwhile, SBE/EBE indicate the illegal
sequence of start bit or end bit for data0~7. So I realize that we should
use -EILSEQ for them both as well CRC cases.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Guodong Xu [Fri, 12 Aug 2016 08:51:26 +0000 (16:51 +0800)]
mmc: dw_mmc: add reset support to dwmmc host controller
Dwmmc host controller may in unknown state when entering kernel boot. One
example is when booting from eMMC, bootloader need initialize MMC host
controller into some state so it can read. In order to make sure MMC host
controller in a clean initial state, this reset support is added.
With this patch, a 'resets' property can be added into dw_mmc device
tree node. The hardware logic is: dwmmc host controller IP receives a reset
signal from a 'reset provider' (eg. power management unit). The 'resets'
property points to this reset signal. So, during dwmmc driver probe,
it can use this signal to reset itself.
Refer to [1] for more information.
[1] Documentation/devicetree/bindings/reset/reset.txt
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Guodong Xu [Fri, 12 Aug 2016 08:51:25 +0000 (16:51 +0800)]
Documentation: synopsys-dw-mshc: add binding for resets
Add resets property to synopsys-dw-mshc bindings. It is intended to
represent the hardware reset signal present internally in some host
controller IC designs.
See Documentation/devicetree/bindings/reset/reset.txt for details.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jaehoon Chung [Fri, 15 Jul 2016 01:54:08 +0000 (10:54 +0900)]
mmc: dw_mmc: remove the unnecessary IS_ERR() checking for ciu/biu clock
If ciu/biu clock are NULL, clk_disable_unprepare should be just
returned. In clk_disable_unprepare(), already checked whether clk is
error or NULL.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Shawn Lin [Fri, 15 Jul 2016 01:47:34 +0000 (09:47 +0800)]
mmc: dw_mmc: remove parsing for each slot subnode
The intention to remove it comes from the conflict of
what the mmc-core does with the way dw_mmc treats disable-wp.
We could see that 'disable-wp' is supported by core but
it's deprecated by dw_mmc as we don't expect it to be existed
for each slot subnode but should be in the parent node. Based
on searching for all the upstream dts using dw_mmc, we're
confident that none of them use the deprecated way. Maybe
we should take old dtb in consideration but it was a flag day
since the time we was considering to take it away. The fact is
that there are none of dts using the deprecated way since v3.18
or even earlier. So personally I don't believe the old dtb
would/could bootup current kernel(may not?). Let's remove it now.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Krzysztof Kozlowski [Thu, 14 Jul 2016 13:22:27 +0000 (15:22 +0200)]
mmc: dw_mmc: exynos: Warn if HS400 is being used on non-Exynos5420 chipset
Chipsets before Exynos5420 did not support HS400 so if MMC core tries to
configure HS400 timing, this might or might not work. Warn in such
cases because this is DTB misconfiguration.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Daniel Glöckner [Tue, 30 Aug 2016 12:17:30 +0000 (14:17 +0200)]
mmc: block: don't use CMD23 with very old MMC cards
CMD23 aka SET_BLOCK_COUNT was introduced with MMC v3.1.
Older versions of the specification allowed to terminate
multi-block transfers only with CMD12.
The patch fixes the following problem:
mmc0: new MMC card at address 0001
mmcblk0: mmc0:0001 SDMB-16 15.3 MiB
mmcblk0: timed out sending SET_BLOCK_COUNT command, card status 0x400900
...
blk_update_request: I/O error, dev mmcblk0, sector 0
Buffer I/O error on dev mmcblk0, logical block 0, async page read
mmcblk0: unable to read partition table
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ulf Hansson [Tue, 30 Aug 2016 07:23:12 +0000 (09:23 +0200)]
mmc: sdhci: Remove ->platform_init() callback as it's no longer used
The commit
1ef5e49e46b9 ("mmc: sdhci-of-esdhc: add/remove some quirks
according to vendor version") moved sdhci-of-esdhc away from using the
->platform_init() callback.
As it was the only user of it and that it seems reasonable to believe that
it won't be needed again, let's just remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Andy Shevchenko [Thu, 18 Aug 2016 11:59:13 +0000 (14:59 +0300)]
mmc: sdhci-pci: Convert to use managed functions (part2)
The commit
52ac7acf412b ("mmc: sdhci-pci: Convert to use managed functions
pcim_* and devm_*") converted ->probe() / ->remove() functions to use device
managed resource API. Here is a follow up to cover sdhci_pci_probe_slot() and
sdhci_pci_remove_slot().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Shawn Lin [Fri, 26 Aug 2016 00:49:56 +0000 (08:49 +0800)]
mmc: sdio: deploy error handling instead of triggering BUG_ON
When using mmc_io_rw_extended, it's intent to avoid null
pointer of card and invalid func number. But actually it
didn't prevent that as the seg_size already use the card.
Currently the wrapper function sdio_io_rw_ext_helper already
use card before calling mmc_io_rw_extended, so we should move
this check to there. As to the func number, it was token from
'(ocr & 0x70000000) >> 28' which should be enough to guarantee
that it won't be larger than 7. But we should prevent the
caller like wifi drivers modify this value. So let's move this
check into sdio_io_rw_ext_helper either.
Also we remove the BUG_ON for mmc_send_io_op_cond since all
possible paths calling this function are protected by checking
the arguments in advance. After deploying these changes, we
could not see any panic within SDIO API even if func drivers
abuse the SDIO func APIs.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Shawn Lin [Fri, 26 Aug 2016 00:49:55 +0000 (08:49 +0800)]
mmc: block: remove the check of packed for packed request routine
packed should always exist without calling its cleanup function
explicitly. Moreover, we have use it when preparing packed list.
So I don't believe we should ever fall into this check again when
doing mmc_blk_packed_hdr_wrq_prep or mmc_blk_end_packed_req,etc.
And the code of mmc_blk_end_packed_req is trying to use packed before
checking it which makes it quite weird. This patch is trying to
remove these two checks and move it to the mmc_blk_prep_packed_list.
If we find packed is null, then we should never use MMC_BLK_PACKED_CMD.
By doing this, we could fall back to non-packed request if finding null
packed, though it's impossible theoretically.
After removing these two BUG_ONs, we also remove all other similar
checks within the routine of mmc_blk_issue_rw_rq which checks the
error handling of packed request.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jungseung Lee [Wed, 24 Aug 2016 10:34:09 +0000 (19:34 +0900)]
mmc: core: Add error message when switching fails in mmc_select_hs()
The switch failure message in mmc_select_timing() had been removed
since that is invalid: commit
0400ed0a083a ("mmc: core: remove the
invalid message in mmc_select_timing")
Now, in the case when mmc_select_hs() return error in mmc_select_timing(),
there is nothing to print failure message.
Let's make for mmc_select_hs() print message itself in the failure case.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wolfram Sang [Wed, 24 Aug 2016 09:34:38 +0000 (11:34 +0200)]
mmc: host: sh_mobile_sdhi: don't populate unneeded functions
Populating card_busy caused a side-effect on a chip variant we don't
have documentation for (r8a73a4). So, enable it and voltage switching
only on devices known to support those features.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Fixes: 452e5eef6d31 ("mmc: tmio: Add UHS-I mode support")
Wolfram Sang [Wed, 24 Aug 2016 09:34:37 +0000 (11:34 +0200)]
mmc: host: sh_mobile_sdhi: move card_busy from tmio to sdhi
card_busy is only used/tested on SDHI for R-Car Gen2 and later.
Move it to the SDHI driver, so we can then activate it conditionally
depending on the SDHI type.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Michael Weiser [Mon, 22 Aug 2016 16:42:18 +0000 (18:42 +0200)]
mmc: sunxi-mmc: change idma descriptor to __le32
The sunxi-mmc driver does not take into account the processor may be big
endian when writing the DMA descriptors. This causes cards not to be
detected when running a big-endian kernel. Change the descriptors for
IDMA to use __le32 and ensure they are suitably swapped before writing.
Tested successfully on the Cubieboard2.
Signed-off-by: Michael Weiser <michael.weiser@gmx.de>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Jean-Francois Moine [Tue, 23 Aug 2016 08:51:04 +0000 (10:51 +0200)]
mmc: sunxi: Check the value returned by clk_round_rate
clk_round_rate() may return an error. Check it.
Signed-off-by: Jean-Francois Moine <moinejf@free.fr>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Douglas Anderson [Thu, 18 Aug 2016 17:26:38 +0000 (10:26 -0700)]
mmc: sdhci-of-arasan: Don't power PHY w/ slow/no clock
PHY intended to be used with the Arasan SDHCI 5.1 controller has trouble
turning on when the card clock is slow or off. Strangely these problems
appear to show up consistently on some boards while other boards work
fine, but on the boards where it shows up the problem reproduces 100% of
the time and is quite consistent in its behavior.
These problems can be fixed by always making sure that we power on the
PHY (and turn on its DLL) when the card clock is faster than about 50
MHz. Once on, we need to make sure that we never power down the PHY /
turn off its DLL until the clock is faster again.
We'll add logic for handling this into the sdhci-of-arasan driver. Note
that right now the only user of a PHY in the sdhci-of-arasan driver is
arasan,sdhci-5.1. It's presumed that all arasan,sdhci-5.1 PHY
implementations need this workaround, so the logic is only contingent on
having a PHY to control. If future Arasan controllers don't have this
problem we can add code to decide if we want this flow or not.
Also note that we check for slow clocks by checking for <= 400 kHz
rather than checking for 50 MHz. This keeps things the most consistent
and also means we can power the PHY on at max speed (where the DLL will
lock fastest). Presumably anyone who intends to run with a card clock
of < 50 MHz and > 400 kHz will be running on a device where this problem
is fixed anyway.
I believe this brings some resolution to the problems reported before.
See the commit
6fc09244d74d ("mmc: sdhci-of-arasan: Revert: Always power
the PHY off/on when clock changes").
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Christopher Freeman [Wed, 17 Aug 2016 17:34:27 +0000 (13:34 -0400)]
mmc: sdhci: Do not allow tuning procedure to be interrupted
wait_event_interruptible_timeout() will return early if the blocked
process receives a signal, causing the driver to abort the tuning
procedure and possibly leaving the controller in a bad state. Since the
tuning command is expected to complete quickly (<50ms) and we've set a
timeout, use wait_event_timeout() instead.
Signed-off-by: Christopher Freeman <cfreeman@nvidia.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Haibo Chen [Mon, 15 Aug 2016 08:31:33 +0000 (16:31 +0800)]
mmc: sdhci-esdhc-imx: correct the max timeout count
i.MX USDHC Reference Manual has a mistake, for the register SYS_CTRL,
the DTOCV(bit 19~16) means the data timeout counter value. When DTOCV
is set to 0xF, it means SDCLK << 29, not SDCLK << 28.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Haibo Chen [Mon, 15 Aug 2016 08:19:38 +0000 (16:19 +0800)]
mmc: sdhci-esdhc-imx: do not touch other bit when config DTOCV
Now, when call esdhc_set_timeout() to set the data timeout counter value,
IPP_RST_N(bit 23) is wrongly affected. This patch add a mask to avoid this.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Acked-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Markus Elfring [Mon, 15 Aug 2016 05:32:45 +0000 (07:32 +0200)]
mmc: sdhci-brcmstb: Delete owner assignment
The field "owner" is set by core. Thus delete an extra initialisation.
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Uri Yanai [Sun, 14 Aug 2016 08:46:36 +0000 (11:46 +0300)]
mmc: sd: Export SD Status via “ssr” device attribute
The SD Status register contains several important fields related to the
SD Card proprietary features.
Those fields may be used by user space applications for vendor specific
usage.
None of those fields are exported today by the driver to user space.
In this patch, we are reading the SD Status register and exporting
(using MMC_DEV_ATTR) the SD Status register to the user space.
Signed-off-by: Uri Yanai <uri.yanai@sandisk.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wolfram Sang [Thu, 11 Aug 2016 21:03:53 +0000 (23:03 +0200)]
mmc: vub300: don't print error when allocating urb fails
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Julia Lawall [Fri, 5 Aug 2016 08:56:46 +0000 (10:56 +0200)]
mmc: sdhci-of-esdhc: use of_property_read_bool
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2;
statement S2,S1;
@@
- if (of_get_property(e1,e2,NULL))
+ if (of_property_read_bool(e1,e2))
S1 else S2
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Ben Dooks [Mon, 1 Aug 2016 09:22:11 +0000 (10:22 +0100)]
mmc: core: Add the vmmc/vmmcq regulator info
The core MMC code adds two (optional) regulator properites that drivers
should use to get their supplies. This is not documented anywhere so add
information on it.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Wei Yongjun [Thu, 28 Jul 2016 16:17:44 +0000 (16:17 +0000)]
mmc: sdhci-bcm-kona: fix error return code in sdhci_bcm_kona_probe()
In clk_set_rate() or clk_prepare_enable() error handling case, the
error return code ret is not set, so sdhci_bcm_kona_probe() return
0 in those error cases.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Acked-by: Ray Jui <ray.jui@broadcom.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Nicholas Mc Guire [Mon, 25 Jul 2016 17:59:23 +0000 (19:59 +0200)]
mmc: moxart: fix wait_for_completion_interruptible_timeout return variable type
wait_for_completion_timeout_interruptible returns long not unsigned long
so dma_time, which is used exclusively here, is changed to long.
Fixes: 1b66e94e6b99 ("mmc: moxart: Add MOXA ART SD/MMC driver")
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hans de Goede [Sun, 7 Aug 2016 19:02:38 +0000 (21:02 +0200)]
mmc: pwrseq-simple: Add an optional post-power-on-delay
Some devices need a while to boot their firmware after providing clks /
de-asserting resets before they are ready to receive sdio commands.
This commits adds a post-power-on-delay-ms devicetree property to
mmc-pwrseq-simple for use with such devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hans de Goede [Sat, 30 Jul 2016 15:03:50 +0000 (17:03 +0200)]
dt: bindings: Make compatible optional for mmc function nodes
On some boards (android tablets) different batches use different sdio
wifi modules. This is not a problem since mmc/sdio is an enumerable bus,
so we only need to describe and activate the mmc controller in dt and
then the kernel will automatically load the right driver.
Sometimes it is useful to specify certain ethernet properties for these
"unknown" sdio devices, specifically we want the boot-loader to be able
to set "local-mac-address" as some of these sdio wifi modules come without
an eeprom / without a factory programmed mac address.
Since the exact device is unknown (differs per batch) we cannot use
a wifi-chip specific compatible, thus sometimes it is desirable to have a
mmc function node, without having to make up an otherwise unused compatible
for the node, so make the compatible property optional.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hans de Goede [Sat, 30 Jul 2016 14:25:48 +0000 (16:25 +0200)]
ARM: dts: sunxi: Use new sun7i-a20-mmc compatible on sun7i and newer
Use the new sun7i-a20-mmc compatible for the mmc controllers on sun7i
and newer.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hans de Goede [Sat, 30 Jul 2016 14:25:47 +0000 (16:25 +0200)]
mmc: sunxi: sun4i / sun5i do not have sample clocks
It turns out that sun4i (A10) and sun5i (A13 & co) do not have sample
clocks, so add a new sun7i-a20-mmc compatible and do not try to use
sample clocks on sun4i / sun5i.
Since sun4i / sun5i do not have sample clocks, they cannot (reliably) do
DDR rates, so only set MMC_CAP_1_8V_DDR when we do have sample clks.
Note this patch leaves the clk_prepare_enable() / clk_disable_unprepare()
calls to the sample clks as-is, without adding checks for them being
NULL. All the clk_foo calls accept a NULL clk and will return success when
called with a NULL clk.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hans de Goede [Sat, 30 Jul 2016 14:25:46 +0000 (16:25 +0200)]
mmc: sunxi: Factor out clock phase setting code into a helper function
Add a sunxi_mmc_clk_set_phase() helper function.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hans de Goede [Sat, 30 Jul 2016 14:25:45 +0000 (16:25 +0200)]
mmc: sunxi: Introduce a sunxi_mmc_cfg struct
Create a struct to hold the various model / compatible string dependend
settings.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Hans de Goede [Sat, 30 Jul 2016 14:25:44 +0000 (16:25 +0200)]
mmc: sunxi: Disable sample clks on remove
When support for the sample clks was added calls to prepare_enable
were added to the probe path, but matching calls to disable_unprepare
were forgotten in the remove path, this fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Lee Jones [Thu, 8 Sep 2016 09:11:36 +0000 (11:11 +0200)]
mmc: sdhci-st: Handle interconnect clock
Some ST platforms contain interconnect (ICN) clocks which must be handed
correctly in order to obtain full functionality of a given IP. In this
case, if the ICN clocks are not handled properly by the ST SDHCI driver
MMC will break and the following output can be observed:
[ 13.916949] mmc0: Timeout waiting for hardware interrupt.
[ 13.922349] sdhci: =========== REGISTER DUMP (mmc0)===========
[ 13.928175] sdhci: Sys addr: 0x00000000 | Version: 0x00001002
[ 13.933999] sdhci: Blk size: 0x00007040 | Blk cnt: 0x00000001
[ 13.939825] sdhci: Argument: 0x00fffff0 | Trn mode: 0x00000013
[ 13.945650] sdhci: Present: 0x1fff0206 | Host ctl: 0x00000011
[ 13.951475] sdhci: Power: 0x0000000f | Blk gap: 0x00000080
[ 13.957300] sdhci: Wake-up: 0x00000000 | Clock: 0x00003f07
[ 13.963126] sdhci: Timeout: 0x00000004 | Int stat: 0x00000000
[ 13.968952] sdhci: Int enab: 0x02ff008b | Sig enab: 0x02ff008b
[ 13.974777] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
[ 13.980602] sdhci: Caps: 0x21ed3281 | Caps_1: 0x00000000
[ 13.986428] sdhci: Cmd: 0x0000063a | Max curr: 0x00000000
[ 13.992252] sdhci: Host ctl2: 0x00000000
[ 13.996166] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x7c048200
[ 14.001990] sdhci: ===========================================
[ 14.009802] mmc0: Got data interrupt 0x02000000 even though no data operation was in progress.
A decent point was raised about minimising the use of a local variable that
we 'could' do without. I've chosen consistency over the possibility of
reducing the local variable count by 1. Thinking that it's more important
for the code to be grouped and authoured in a similar manner/style for
greater maintainability/readability.
Cc: stable@vger.kernel.org
Tested-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Lee Jones [Thu, 8 Sep 2016 09:11:35 +0000 (11:11 +0200)]
dt-bindings: mmc: sdhci-st: Mention the discretionary "icn" clock
The interconnect (ICN) clock is required for functional working of
MMC on some ST platforms. When not supplied it can result in
broken MMC and the following output:
[ 13.916949] mmc0: Timeout waiting for hardware interrupt.
[ 13.922349] sdhci: =========== REGISTER DUMP (mmc0)===========
[ 13.928175] sdhci: Sys addr: 0x00000000 | Version: 0x00001002
[ 13.933999] sdhci: Blk size: 0x00007040 | Blk cnt: 0x00000001
[ 13.939825] sdhci: Argument: 0x00fffff0 | Trn mode: 0x00000013
[ 13.945650] sdhci: Present: 0x1fff0206 | Host ctl: 0x00000011
[ 13.951475] sdhci: Power: 0x0000000f | Blk gap: 0x00000080
[ 13.957300] sdhci: Wake-up: 0x00000000 | Clock: 0x00003f07
[ 13.963126] sdhci: Timeout: 0x00000004 | Int stat: 0x00000000
[ 13.968952] sdhci: Int enab: 0x02ff008b | Sig enab: 0x02ff008b
[ 13.974777] sdhci: AC12 err: 0x00000000 | Slot int: 0x00000000
[ 13.980602] sdhci: Caps: 0x21ed3281 | Caps_1: 0x00000000
[ 13.986428] sdhci: Cmd: 0x0000063a | Max curr: 0x00000000
[ 13.992252] sdhci: Host ctl2: 0x00000000
[ 13.996166] sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x7c048200
[ 14.001990] sdhci: ===========================================
[ 14.009802] mmc0: Got data interrupt 0x02000000 even though no data operation was in progress.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Linus Torvalds [Mon, 12 Sep 2016 03:02:25 +0000 (20:02 -0700)]
Linux 4.8-rc6
Linus Torvalds [Sun, 11 Sep 2016 21:41:49 +0000 (14:41 -0700)]
nvme: make NVME_RDMA depend on BLOCK
Commit
aa71987472a9 ("nvme: fabrics drivers don't need the nvme-pci
driver") removed the dependency on BLK_DEV_NVME, but the cdoe does
depend on the block layer (which used to be an implicit dependency
through BLK_DEV_NVME).
Otherwise you get various errors from the kbuild test robot random
config testing when that happens to hit a configuration with BLOCK
device support disabled.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Jay Freyensee <james_p_freyensee@linux.intel.com>
Cc: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Linus Torvalds [Sun, 11 Sep 2016 21:23:48 +0000 (14:23 -0700)]
Merge tag 'staging-4.8-rc6' of git://git./linux/kernel/git/gregkh/staging
Pull IIO fixes from Greg KH:
"Here are a few small IIO fixes for 4.8-rc6.
Nothing major, full details are in the shortlog, all of these have
been in linux-next with no reported issues"
* tag 'staging-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
iio:core: fix IIO_VAL_FRACTIONAL sign handling
iio: ensure ret is initialized to zero before entering do loop
iio: accel: kxsd9: Fix scaling bug
iio: accel: bmc150: reset chip at init time
iio: fix pressure data output unit in hid-sensor-attributes
tools:iio:iio_generic_buffer: fix trigger-less mode
Linus Torvalds [Sun, 11 Sep 2016 21:10:29 +0000 (14:10 -0700)]
Merge tag 'usb-4.8-rc6' of git://git./linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB gadget, phy, and xhci fixes for 4.8-rc6.
All of these resolve minor issues that have been reported, and all
have been in linux-next with no reported issues"
* tag 'usb-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: chipidea: udc: fix NULL ptr dereference in isr_setup_status_phase
xhci: fix null pointer dereference in stop command timeout function
usb: dwc3: pci: fix build warning on !PM_SLEEP
usb: gadget: prevent potenial null pointer dereference on skb->len
usb: renesas_usbhs: fix clearing the {BRDY,BEMP}STS condition
usb: phy: phy-generic: Check clk_prepare_enable() error
usb: gadget: udc: renesas-usb3: clear VBOUT bit in DRD_CON
Revert "usb: dwc3: gadget: always decrement by 1"
Linus Torvalds [Sat, 10 Sep 2016 16:58:52 +0000 (09:58 -0700)]
Merge branch 'libnvdimm-fixes' of git://git./linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"nvdimm fixes for v4.8, two of them are tagged for -stable:
- Fix devm_memremap_pages() to use track_pfn_insert(). Otherwise,
DAX pmd mappings end up with an uncached pgprot, and unusable
performance for the device-dax interface. The device-dax interface
appeared in 4.7 so this is tagged for -stable.
- Fix a couple VM_BUG_ON() checks in the show_smaps() path to
understand DAX pmd entries. This fix is tagged for -stable.
- Fix a mis-merge of the nfit machine-check handler to flip the
polarity of an if() to match the final version of the patch that
Vishal sent for 4.8-rc1. Without this the nfit machine check
handler never detects / inserts new 'badblocks' entries which
applications use to identify lost portions of files.
- For test purposes, fix the nvdimm_clear_poison() path to operate on
legacy / simulated nvdimm memory ranges. Without this fix a test
can set badblocks, but never clear them on these ranges.
- Fix the range checking done by dax_dev_pmd_fault(). This is not
tagged for -stable since this problem is mitigated by specifying
aligned resources at device-dax setup time.
These patches have appeared in a next release over the past week. The
recent rebase you can see in the timestamps was to drop an invalid fix
as identified by the updated device-dax unit tests [1]. The -mm
touches have an ack from Andrew"
[1]: "[ndctl PATCH 0/3] device-dax test for recent kernel bugs"
https://lists.01.org/pipermail/linux-nvdimm/2016-September/006855.html
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm: allow legacy (e820) pmem region to clear bad blocks
nfit, mce: Fix SPA matching logic in MCE handler
mm: fix cache mode of dax pmd mappings
mm: fix show_smap() for zone_device-pmd ranges
dax: fix mapping size check
Linus Torvalds [Sat, 10 Sep 2016 16:43:10 +0000 (09:43 -0700)]
Merge branch 'i2c/for-current' of git://git./linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Mostly driver bugfixes, but also a few cleanups which are nice to have
out of the way"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
i2c: rk3x: Restore clock settings at resume time
i2c: Spelling s/acknowedge/acknowledge/
i2c: designware: save the preset value of DW_IC_SDA_HOLD
Documentation: i2c: slave-interface: add note for driver development
i2c: mux: demux-pinctrl: run properly with multiple instances
i2c: bcm-kona: fix inconsistent indenting
i2c: rcar: use proper device with dma_mapping_error
i2c: sh_mobile: use proper device with dma_mapping_error
i2c: mux: demux-pinctrl: invalidate properly when switching fails
Linus Torvalds [Sat, 10 Sep 2016 16:18:33 +0000 (09:18 -0700)]
Merge tag 'for_linus_stable' of git://git./linux/kernel/git/tytso/ext4
Pull fscrypto fixes fromTed Ts'o:
"Fix some brown-paper-bag bugs for fscrypto, including one one which
allows a malicious user to set an encryption policy on an empty
directory which they do not own"
* tag 'for_linus_stable' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4:
fscrypto: require write access to mount to set encryption policy
fscrypto: only allow setting encryption policy on directories
fscrypto: add authorization check for setting encryption policy
Eric Biggers [Thu, 8 Sep 2016 21:20:38 +0000 (14:20 -0700)]
fscrypto: require write access to mount to set encryption policy
Since setting an encryption policy requires writing metadata to the
filesystem, it should be guarded by mnt_want_write/mnt_drop_write.
Otherwise, a user could cause a write to a frozen or readonly
filesystem. This was handled correctly by f2fs but not by ext4. Make
fscrypt_process_policy() handle it rather than relying on the filesystem
to get it right.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Cc: stable@vger.kernel.org # 4.1+; check fs/{ext4,f2fs}
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Acked-by: Jaegeuk Kim <jaegeuk@kernel.org>
Eric Biggers [Thu, 8 Sep 2016 18:36:39 +0000 (11:36 -0700)]
fscrypto: only allow setting encryption policy on directories
The FS_IOC_SET_ENCRYPTION_POLICY ioctl allowed setting an encryption
policy on nondirectory files. This was unintentional, and in the case
of nonempty regular files did not behave as expected because existing
data was not actually encrypted by the ioctl.
In the case of ext4, the user could also trigger filesystem errors in
->empty_dir(), e.g. due to mismatched "directory" checksums when the
kernel incorrectly tried to interpret a regular file as a directory.
This bug affected ext4 with kernels v4.8-rc1 or later and f2fs with
kernels v4.6 and later. It appears that older kernels only permitted
directories and that the check was accidentally lost during the
refactoring to share the file encryption code between ext4 and f2fs.
This patch restores the !S_ISDIR() check that was present in older
kernels.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Cc: stable@vger.kernel.org
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Eric Biggers [Thu, 8 Sep 2016 17:57:08 +0000 (10:57 -0700)]
fscrypto: add authorization check for setting encryption policy
On an ext4 or f2fs filesystem with file encryption supported, a user
could set an encryption policy on any empty directory(*) to which they
had readonly access. This is obviously problematic, since such a
directory might be owned by another user and the new encryption policy
would prevent that other user from creating files in their own directory
(for example).
Fix this by requiring inode_owner_or_capable() permission to set an
encryption policy. This means that either the caller must own the file,
or the caller must have the capability CAP_FOWNER.
(*) Or also on any regular file, for f2fs v4.6 and later and ext4
v4.8-rc1 and later; a separate bug fix is coming for that.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Cc: stable@vger.kernel.org # 4.1+; check fs/{ext4,f2fs}
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Dave Jiang [Fri, 9 Sep 2016 16:10:08 +0000 (09:10 -0700)]
libnvdimm: allow legacy (e820) pmem region to clear bad blocks
Bad blocks can be injected via /sys/block/pmemN/badblocks. In a situation
where legacy pmem is being used or a pmem region created by using memmap
kernel parameter, the injected bad blocks are not cleared due to
nvdimm_clear_poison() failing from lack of ndctl function pointer. In
this case we need to just return as handled and allow the bad blocks to
be cleared rather than fail.
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Vishal Verma [Fri, 2 Sep 2016 23:27:30 +0000 (17:27 -0600)]
nfit, mce: Fix SPA matching logic in MCE handler
The check for a 'pmem' type SPA in the MCE handler was inverted due to a
merge/rebase error.
Fixes: 6839a6d nfit: do an ARS scrub on hitting a latent media error
Cc: linux-acpi@vger.kernel.org
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Wed, 7 Sep 2016 15:51:21 +0000 (08:51 -0700)]
mm: fix cache mode of dax pmd mappings
track_pfn_insert() in vmf_insert_pfn_pmd() is marking dax mappings as
uncacheable rendering them impractical for application usage. DAX-pte
mappings are cached and the goal of establishing DAX-pmd mappings is to
attain more performance, not dramatically less (3 orders of magnitude).
track_pfn_insert() relies on a previous call to reserve_memtype() to
establish the expected page_cache_mode for the range. While memremap()
arranges for reserve_memtype() to be called, devm_memremap_pages() does
not. So, teach track_pfn_insert() and untrack_pfn() how to handle
tracking without a vma, and arrange for devm_memremap_pages() to
establish the write-back-cache reservation in the memtype tree.
Cc: <stable@vger.kernel.org>
Cc: Matthew Wilcox <mawilcox@microsoft.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Nilesh Choudhury <nilesh.choudhury@oracle.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reported-by: Toshi Kani <toshi.kani@hpe.com>
Reported-by: Kai Zhang <kai.ka.zhang@oracle.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Dan Williams [Sat, 3 Sep 2016 17:38:03 +0000 (10:38 -0700)]
mm: fix show_smap() for zone_device-pmd ranges
Attempting to dump /proc/<pid>/smaps for a process with pmd dax mappings
currently results in the following VM_BUG_ONs:
kernel BUG at mm/huge_memory.c:1105!
task:
ffff88045f16b140 task.stack:
ffff88045be14000
RIP: 0010:[<
ffffffff81268f9b>] [<
ffffffff81268f9b>] follow_trans_huge_pmd+0x2cb/0x340
[..]
Call Trace:
[<
ffffffff81306030>] smaps_pte_range+0xa0/0x4b0
[<
ffffffff814c2755>] ? vsnprintf+0x255/0x4c0
[<
ffffffff8123c46e>] __walk_page_range+0x1fe/0x4d0
[<
ffffffff8123c8a2>] walk_page_vma+0x62/0x80
[<
ffffffff81307656>] show_smap+0xa6/0x2b0
kernel BUG at fs/proc/task_mmu.c:585!
RIP: 0010:[<
ffffffff81306469>] [<
ffffffff81306469>] smaps_pte_range+0x499/0x4b0
Call Trace:
[<
ffffffff814c2795>] ? vsnprintf+0x255/0x4c0
[<
ffffffff8123c46e>] __walk_page_range+0x1fe/0x4d0
[<
ffffffff8123c8a2>] walk_page_vma+0x62/0x80
[<
ffffffff81307696>] show_smap+0xa6/0x2b0
These locations are sanity checking page flags that must be set for an
anonymous transparent huge page, but are not set for the zone_device
pages associated with dax mappings.
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Linus Torvalds [Fri, 9 Sep 2016 21:52:05 +0000 (14:52 -0700)]
Merge tag 'for_linus' of git://git./linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"This includes a couple of bugfixs for virtio.
The virtio console patch is actually also in x86/tip targeting 4.9
because it helps vmap stacks, but it also fixes IOMMU_PLATFORM which
was added in 4.8, and it seems important not to ship that in a broken
configuration"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio_console: Stop doing DMA on the stack
virtio: mark vring_dma_dev() static
Linus Torvalds [Fri, 9 Sep 2016 21:47:41 +0000 (14:47 -0700)]
Merge tag 'pm-4.8-rc6' of git://git./linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"This includes a PM QoS framework fix from Tejun to prevent interrupts
from being enabled unexpectedly during early boot and a cpufreq
documentation fix.
Specifics:
- If the PM QoS framework invokes cancel_delayed_work_sync() during
early boot, it will enable interrupts which is not expected at that
point, so prevent it from happening (Tejun Heo)
- Fix cpufreq statistic documentation to follow a recent change in
behavior that forgot to update it as appropriate (Jean Delvare)"
* tag 'pm-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq-stats: Minor documentation fix
PM / QoS: avoid calling cancel_delayed_work_sync() during early boot
Rafael J. Wysocki [Fri, 9 Sep 2016 20:34:16 +0000 (22:34 +0200)]
Merge branches 'pm-core-fixes' and 'pm-cpufreq-fixes'
* pm-core-fixes:
PM / QoS: avoid calling cancel_delayed_work_sync() during early boot
* pm-cpufreq-fixes:
cpufreq-stats: Minor documentation fix
Linus Torvalds [Fri, 9 Sep 2016 20:09:50 +0000 (13:09 -0700)]
Merge tag 'gpio-v4.8-3' of git://git./linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Some GPIO fixes that have been boiling the last two weeks or so.
Nothing special, I'm trying to sort out some Kconfig business and
Russell needs a fix in for -his SA1100 rework.
Summary:
- Revert a pointless attempt to add an include to solve the UM allyes
compilation problem.
- Make the mcp23s08 depend on OF_GPIO as it uses it and doesn't
compile properly without it.
- Fix a probing problem for ucb1x00"
* tag 'gpio-v4.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: sa1100: fix irq probing for ucb1x00
gpio: mcp23s08: make driver depend on OF_GPIO
Revert "gpio: include <linux/io-mapping.h> in gpiolib-of"
Linus Torvalds [Fri, 9 Sep 2016 20:00:41 +0000 (13:00 -0700)]
Merge branch 'for-linus' of git://git./linux/kernel/git/mszeredi/fuse
Pull fuse fix from Miklos Szeredi:
"This fixes a deadlock when fuse, direct I/O and loop device are
combined"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: direct-io: don't dirty ITER_BVEC pages
Linus Torvalds [Fri, 9 Sep 2016 19:56:28 +0000 (12:56 -0700)]
Merge branch 'overlayfs-linus' of git://git./linux/kernel/git/mszeredi/vfs
Pull overlayfs fix from Miklos Szeredi:
"This fixes a regression caused by the last pull request"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: fix workdir creation
Linus Torvalds [Fri, 9 Sep 2016 19:52:31 +0000 (12:52 -0700)]
Merge branch 'for-linus-4.8' of git://git./linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"I'm not proud of how long it took me to track down that one liner in
btrfs_sync_log(), but the good news is the patches I was trying to
blame for these problems were actually fine (sorry Filipe)"
* 'for-linus-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
btrfs: introduce tickets_id to determine whether asynchronous metadata reclaim work makes progress
btrfs: remove root_log_ctx from ctx list before btrfs_sync_log returns
btrfs: do not decrease bytes_may_use when replaying extents
Linus Torvalds [Fri, 9 Sep 2016 19:02:46 +0000 (12:02 -0700)]
Merge tag 'sound-4.8-rc6' of git://git./linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"We've got quite a few fixes at this time, and all are stable patches.
syzkaller strikes back again (episode 19 or so), and we had to plug
some holes in ALSA core part (mostly timer).
In addition, a couple of FireWire audio fixes for the invalid copy
user calls in locks, and a few quirks for HD-audio and USB-audio as
usual are included"
* tag 'sound-4.8-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: rawmidi: Fix possible deadlock with virmidi registration
ALSA: timer: Fix zero-division by continue of uninitialized instance
ALSA: timer: fix NULL pointer dereference in read()/ioctl() race
ALSA: fireworks: accessing to user space outside spinlock
ALSA: firewire-tascam: accessing to user space outside spinlock
ALSA: hda - Enable subwoofer on Dell Inspiron 7559
ALSA: hda - Add headset mic quirk for Dell Inspiron 5468
ALSA: usb-audio: Add sample rate inquiry quirk for B850V3 CP2114
ALSA: timer: fix NULL pointer dereference on memory allocation failure
ALSA: timer: fix division by zero after SNDRV_TIMER_IOCTL_CONTINUE
Andy Lutomirski [Tue, 30 Aug 2016 15:04:15 +0000 (08:04 -0700)]
virtio_console: Stop doing DMA on the stack
virtio_console uses a small DMA buffer for control requests. Move
that buffer into heap memory.
Doing virtio DMA on the stack is normally okay on non-DMA-API virtio
systems (which is currently most of them), but it breaks completely
if the stack is virtually mapped.
Tested by typing both directions using picocom aimed at /dev/hvc0.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Baoyou Xie [Thu, 1 Sep 2016 11:02:57 +0000 (19:02 +0800)]
virtio: mark vring_dma_dev() static
We get 1 warning when building kernel with W=1:
drivers/virtio/virtio_ring.c:170:16: warning: no previous prototype for 'vring_dma_dev' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is
declared and don't need a declaration, but can be made static.
so this patch marks this function with 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Linus Torvalds [Fri, 9 Sep 2016 17:54:29 +0000 (10:54 -0700)]
Merge tag 'arm64-fixes' of git://git./linux/kernel/git/arm64/linux
Pull arm64 fixes from Catalin Marinas:
- smp_mb__before_spinlock() changed to smp_mb() on arm64 since the
generic definition to smp_wmb() is not sufficient
- avoid a recursive loop with the graph tracer by using using
preempt_(enable|disable)_notrace in _percpu_(read|write)
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: use preempt_disable_notrace in _percpu_read/write
arm64: spinlocks: implement smp_mb__before_spinlock() as smp_mb()
Linus Torvalds [Fri, 9 Sep 2016 15:43:42 +0000 (08:43 -0700)]
Merge tag 'powerpc-4.8-5' of git://git./linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Fixes marked for stable:
- Don't alias user region to other regions below PAGE_OFFSET from
Paul Mackerras
- Fix again csum_partial_copy_generic() on 32-bit from Christophe
Leroy
- Fix corrupted PE allocation bitmap on releasing PE from Gavin Shan
Fixes for code merged this cycle:
- Fix crash on releasing compound PE from Gavin Shan
- Fix processor numbers in OPAL ICP from Benjamin Herrenschmidt
- Fix little endian build with CONFIG_KEXEC=n from Thiago Jung
Bauermann"
* tag 'powerpc-4.8-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/mm: Don't alias user region to other regions below PAGE_OFFSET
powerpc/32: Fix again csum_partial_copy_generic()
powerpc/powernv: Fix corrupted PE allocation bitmap on releasing PE
powerpc/powernv: Fix crash on releasing compound PE
powerpc/xics/opal: Fix processor numbers in OPAL ICP
powerpc/pseries: Fix little endian build with CONFIG_KEXEC=n
Linus Torvalds [Fri, 9 Sep 2016 15:32:10 +0000 (08:32 -0700)]
Merge branch 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM fixes from Russell King:
"A few ARM fixes:
- Robin Murphy noticed that the non-secure privileged entry was
relying on undefined behaviour, which needed to be fixed.
- Vladimir Murzin noticed that prov-v7 fails to build for MMUless
configurations because a required header file wasn't included.
- A bunch of fixes for StrongARM regressions found while testing
4.8-rc on such platforms"
* 'fixes' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: sa1100: clear reset status prior to reboot
ARM: 8600/1: Enforce some NS-SVC initialisation
ARM: 8599/1: mm: pull asm/memory.h explicitly
ARM: sa1100: register clocks early
ARM: sa1100: fix 3.6864MHz clock
Greg Kroah-Hartman [Fri, 9 Sep 2016 13:11:35 +0000 (15:11 +0200)]
Merge tag 'fixes-for-v4.8-rc6' of git://git./linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.8-rc6
Unfortunately we have a bogus dwc3 patch leaked through the cracks and
got merged into Linus' HEAD. That patch ended up causing off-by-1 error
in our TRB accounting logic. Thankfully John Youn found out the problem
and we provided a revert to the bogus dwc3 patch in no time.
Apart from this off-by-1 error, we have two fixes to the Renesas drivers,
a small fix to our generic phy driver, a NULL pointer dereference fix for
f_eem and a build warning fix in dwc3.
Greg Kroah-Hartman [Fri, 9 Sep 2016 11:47:20 +0000 (13:47 +0200)]
Merge tag 'usb-ci-v4.8-rc6' of git://git./linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
Fix the possible kernel panic when the hardware signal is bad for chipidea udc.
Greg Kroah-Hartman [Fri, 9 Sep 2016 11:44:37 +0000 (13:44 +0200)]
Merge tag 'iio-fixes-for-4.8b' of git://git./linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
Second set of IIO fixes for the 4.8 cycle.
We have a big rework of the kxsd9 driver queued up behind the fix below and
a fix for a recent fix that was marked for stable.
Hence this fix series is perhaps a little more urgent than average for IIO.
* core
- a fix for a fix in the last set. The recent fix for blocking ops when
! task running left a path (unlikely one) in which the function return
value was not set - so initialise it to 0.
- The IIO_TYPE_FRACTIONAL code previously didn't cope with negative
fractions. Turned out a fix for this was in Analog's tree but hadn't made
it upstream.
* bmc150
- reset chip at init time. At least one board out there ends up coming up
in an unstable state due to noise during power up. The reset does no
harm on other boards.
* kxsd9
- Fix a bug in the reported scaling due to failing to set the integer
part to 0.
* hid-sensors-pressure
- Output was in the wrong units to comply with the IIO ABI.
* tools
- iio_generic_buffer: Fix the trigger-less mode by ensuring we don't fault
out for having no trigger when we explicitly said we didn't want to have
one.
Chunyan Zhang [Thu, 8 Sep 2016 12:46:42 +0000 (20:46 +0800)]
arm64: use preempt_disable_notrace in _percpu_read/write
When debug preempt or preempt tracer is enabled, preempt_count_add/sub()
can be traced by function and function graph tracing, and
preempt_disable/enable() would call preempt_count_add/sub(), so in Ftrace
subsystem we should use preempt_disable/enable_notrace instead.
In the commit
345ddcc882d8 ("ftrace: Have set_ftrace_pid use the bitmap
like events do") the function this_cpu_read() was added to
trace_graph_entry(), and if this_cpu_read() calls preempt_disable(), graph
tracer will go into a recursive loop, even if the tracing_on is
disabled.
So this patch change to use preempt_enable/disable_notrace instead in
this_cpu_read().
Since Yonghui Yang helped a lot to find the root cause of this problem,
so also add his SOB.
Signed-off-by: Yonghui Yang <mark.yang@spreadtrum.com>
Signed-off-by: Chunyan Zhang <zhang.chunyan@linaro.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Will Deacon [Mon, 5 Sep 2016 10:56:05 +0000 (11:56 +0100)]
arm64: spinlocks: implement smp_mb__before_spinlock() as smp_mb()
smp_mb__before_spinlock() is intended to upgrade a spin_lock() operation
to a full barrier, such that prior stores are ordered with respect to
loads and stores occuring inside the critical section.
Unfortunately, the core code defines the barrier as smp_wmb(), which
is insufficient to provide the required ordering guarantees when used in
conjunction with our load-acquire-based spinlock implementation.
This patch overrides the arm64 definition of smp_mb__before_spinlock()
to map to a full smp_mb().
Cc: <stable@vger.kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Reported-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Clemens Gruber [Mon, 5 Sep 2016 17:29:58 +0000 (19:29 +0200)]
usb: chipidea: udc: fix NULL ptr dereference in isr_setup_status_phase
Problems with the signal integrity of the high speed USB data lines or
noise on reference ground lines can cause the i.MX6 USB controller to
violate USB specs and exhibit unexpected behavior.
It was observed that USBi_UI interrupts were triggered first and when
isr_setup_status_phase was called, ci->status was NULL, which lead to a
NULL pointer dereference kernel panic.
This patch fixes the kernel panic, emits a warning once and returns
-EPIPE to halt the device and let the host get stalled.
It also adds a comment to point people, who are experiencing this issue,
to their USB hardware design.
Cc: <stable@vger.kernel.org> #4.1+
Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Jean Delvare [Thu, 8 Sep 2016 21:05:07 +0000 (23:05 +0200)]
cpufreq-stats: Minor documentation fix
The cpufreq-stats code can no longer be built as a module, so it now
appears with square brackets in menuconfig.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: 1aefc75b2449 (cpufreq: stats: Make the stats code non-modular)
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Doug Anderson [Mon, 29 Aug 2016 21:22:36 +0000 (14:22 -0700)]
i2c: rk3x: Restore clock settings at resume time
Depending on a number of factors including:
- Which exact Rockchip SoC we're working with
- How deep we suspend
- Which i2c port we're on
We might lose the state of the i2c registers at suspend time.
Specifically we've found that on rk3399 the i2c ports that are not in
the PMU power domain lose their state with the current suspend depth
configured by ARM Tursted Firmware.
Note that there are very few actual i2c registers that aren't configured
per transfer anyway so all we actually need to re-configure are the
clock config registers. We'll just add a call to rk3x_i2c_adapt_div()
at resume time and be done with it.
NOTE: On rk3399 on ports whose power was lost, I put printouts in at
resume time. I saw things like:
before: con=0x00010300, div=0x00060006
after: con=0x00010200, div=0x00180025
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: David Wu <david.wu@rock-chips.com>
Tested-by: David Wu <david.wu@rock-chips.com>
[wsa: removed duplicate const]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Geert Uytterhoeven [Wed, 31 Aug 2016 09:38:48 +0000 (11:38 +0200)]
i2c: Spelling s/acknowedge/acknowledge/
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Zhuo-hao Lee [Sat, 27 Aug 2016 07:39:30 +0000 (15:39 +0800)]
i2c: designware: save the preset value of DW_IC_SDA_HOLD
There are several ways to set the SDA hold time for i2c controller,
including: Device Tree, built-in device properties and ACPI. However,
if the SDA hold time is not specified by above method, we should
read the value, where it is preset by firmware, and save it to
sda_hold_time. This is needed because when i2c controller enters
runtime suspend, the DW_IC_SDA_HOLD value will be reset to chipset
default value. And during runtime resume, i2c_dw_init will be called
to reconfigure i2c controller. If sda_hold_time is zero, the chipset
default hold time will be used, that will be too short for some
platforms. Therefore, to have a better tolerance, the DW_IC_SDA_HOLD
value should be kept by sda_hold_time.
Signed-off-by: Zhuo-hao Lee <zhuo-hao.lee@intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Linus Torvalds [Thu, 8 Sep 2016 19:23:13 +0000 (12:23 -0700)]
Merge tag 'ceph-for-4.8-rc6' of git://github.com/ceph/ceph-client
Pull ceph fix from Ilya Dryomov:
"A fix for a 4.7 performance regression, caused by a typo in an if
condition"
* tag 'ceph-for-4.8-rc6' of git://github.com/ceph/ceph-client:
ceph: do not modify fi->frag in need_reset_readdir()
Linus Torvalds [Thu, 8 Sep 2016 19:19:24 +0000 (12:19 -0700)]
Merge branch 'dmi-for-linus' of git://git./linux/kernel/git/jdelvare/staging
Pull dmi fix from Jean Delvare.
* 'dmi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
dmi-id: don't free dev structure after calling device_register
Linus Torvalds [Thu, 8 Sep 2016 19:05:15 +0000 (12:05 -0700)]
Merge tag 'armsoc-fixes' of git://git./linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"This is a slightly larger batch of fixes that we've been sitting on a
few -rcs. Most of them are simple oneliners, but there are two sets
that are slightly larger and worth pointing out:
- A set of patches to OMAP to deal with hwmod for RTC on am33xx
(beaglebone SoC, among others). It's the only clock that ever has
a valid offset of 0, so a new flag needed introduction once this
problem was discovered.
- A collection of CCI fixes for performance counters discovered once
people started using it on X-Gene CPUs"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (37 commits)
arm-cci: pmu: Fix typo in event name
Revert "ARM: tegra: fix erroneous address in dts"
ARM: dts: imx6qdl: Fix SPDIF regression
ARM: imx6: add missing BM_CLPCR_BYPASS_PMIC_READY setting for imx6sx
ARM: dts: imx7d-sdb: fix ti,x-plate-ohms property name
ARM: dts: kirkwood: Fix PCIe label on OpenRD
ARM: kirkwood: ib62x0: fix size of u-boot environment partition
bus: arm-ccn: make event groups reliable
bus: arm-ccn: fix hrtimer registration
bus: arm-ccn: fix PMU interrupt flags
ARM: tegra: Correct polarity for Tegra114 PMIC interrupt
MAINTAINERS: add tree entry for ARM/UniPhier architecture
ARM: sun5i: Fix typo in trip point temperature
MAINTAINERS: Switch to kernel.org account for Krzysztof Kozlowski
ARM: imx6ul: populates platform device at .init_machine
bus: arm-ccn: Add missing event attribute exclusions for host/guest
bus: arm-ccn: Correct required arguments for XP PMU events
bus: arm-ccn: Fix XP watchpoint settings bitmask
bus: arm-ccn: Do not attempt to configure XPs for cycle counter
bus: arm-ccn: Fix PMU handling of MN
...
Wolfram Sang [Thu, 25 Aug 2016 17:27:40 +0000 (19:27 +0200)]
Documentation: i2c: slave-interface: add note for driver development
Make it clear that adding slave support shall not disable master
functionality. We can have both, so we should.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Wolfram Sang [Tue, 23 Aug 2016 15:28:03 +0000 (17:28 +0200)]
i2c: mux: demux-pinctrl: run properly with multiple instances
We can't use a static property for all the changesets, so we now create
dynamic ones for each changeset.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Fixes: 50a5ba87690814 ("i2c: mux: demux-pinctrl: add driver")
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Takashi Iwai [Tue, 30 Aug 2016 12:45:46 +0000 (14:45 +0200)]
ALSA: rawmidi: Fix possible deadlock with virmidi registration
When a seq-virmidi driver is initialized, it registers a rawmidi
instance with its callback to create an associated seq kernel client.
Currently it's done throughly in rawmidi's register_mutex context.
Recently it was found that this may lead to a deadlock another rawmidi
device that is being attached with the sequencer is accessed, as both
open with the same register_mutex. This was actually triggered by
syzkaller, as Dmitry Vyukov reported:
======================================================
[ INFO: possible circular locking dependency detected ]
4.8.0-rc1+ #11 Not tainted
-------------------------------------------------------
syz-executor/7154 is trying to acquire lock:
(register_mutex#5){+.+.+.}, at: [<
ffffffff84fd6d4b>] snd_rawmidi_kernel_open+0x4b/0x260 sound/core/rawmidi.c:341
but task is already holding lock:
(&grp->list_mutex){++++.+}, at: [<
ffffffff850138bb>] check_and_subscribe_port+0x5b/0x5c0 sound/core/seq/seq_ports.c:495
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (&grp->list_mutex){++++.+}:
[<
ffffffff8147a3a8>] lock_acquire+0x208/0x430 kernel/locking/lockdep.c:3746
[<
ffffffff863f6199>] down_read+0x49/0xc0 kernel/locking/rwsem.c:22
[< inline >] deliver_to_subscribers sound/core/seq/seq_clientmgr.c:681
[<
ffffffff85005c5e>] snd_seq_deliver_event+0x35e/0x890 sound/core/seq/seq_clientmgr.c:822
[<
ffffffff85006e96>] > snd_seq_kernel_client_dispatch+0x126/0x170 sound/core/seq/seq_clientmgr.c:2418
[<
ffffffff85012c52>] snd_seq_system_broadcast+0xb2/0xf0 sound/core/seq/seq_system.c:101
[<
ffffffff84fff70a>] snd_seq_create_kernel_client+0x24a/0x330 sound/core/seq/seq_clientmgr.c:2297
[< inline >] snd_virmidi_dev_attach_seq sound/core/seq/seq_virmidi.c:383
[<
ffffffff8502d29f>] snd_virmidi_dev_register+0x29f/0x750 sound/core/seq/seq_virmidi.c:450
[<
ffffffff84fd208c>] snd_rawmidi_dev_register+0x30c/0xd40 sound/core/rawmidi.c:1645
[<
ffffffff84f816d3>] __snd_device_register.part.0+0x63/0xc0 sound/core/device.c:164
[< inline >] __snd_device_register sound/core/device.c:162
[<
ffffffff84f8235d>] snd_device_register_all+0xad/0x110 sound/core/device.c:212
[<
ffffffff84f7546f>] snd_card_register+0xef/0x6c0 sound/core/init.c:749
[<
ffffffff85040b7f>] snd_virmidi_probe+0x3ef/0x590 sound/drivers/virmidi.c:123
[<
ffffffff833ebf7b>] platform_drv_probe+0x8b/0x170 drivers/base/platform.c:564
......
-> #0 (register_mutex#5){+.+.+.}:
[< inline >] check_prev_add kernel/locking/lockdep.c:1829
[< inline >] check_prevs_add kernel/locking/lockdep.c:1939
[< inline >] validate_chain kernel/locking/lockdep.c:2266
[<
ffffffff814791f4>] __lock_acquire+0x4d44/0x4d80 kernel/locking/lockdep.c:3335
[<
ffffffff8147a3a8>] lock_acquire+0x208/0x430 kernel/locking/lockdep.c:3746
[< inline >] __mutex_lock_common kernel/locking/mutex.c:521
[<
ffffffff863f0ef1>] mutex_lock_nested+0xb1/0xa20 kernel/locking/mutex.c:621
[<
ffffffff84fd6d4b>] snd_rawmidi_kernel_open+0x4b/0x260 sound/core/rawmidi.c:341
[<
ffffffff8502e7c7>] midisynth_subscribe+0xf7/0x350 sound/core/seq/seq_midi.c:188
[< inline >] subscribe_port sound/core/seq/seq_ports.c:427
[<
ffffffff85013cc7>] check_and_subscribe_port+0x467/0x5c0 sound/core/seq/seq_ports.c:510
[<
ffffffff85015da9>] snd_seq_port_connect+0x2c9/0x500 sound/core/seq/seq_ports.c:579
[<
ffffffff850079b8>] snd_seq_ioctl_subscribe_port+0x1d8/0x2b0 sound/core/seq/seq_clientmgr.c:1480
[<
ffffffff84ffe9e4>] snd_seq_do_ioctl+0x184/0x1e0 sound/core/seq/seq_clientmgr.c:2225
[<
ffffffff84ffeae8>] snd_seq_kernel_client_ctl+0xa8/0x110 sound/core/seq/seq_clientmgr.c:2440
[<
ffffffff85027664>] snd_seq_oss_midi_open+0x3b4/0x610 sound/core/seq/oss/seq_oss_midi.c:375
[<
ffffffff85023d67>] snd_seq_oss_synth_setup_midi+0x107/0x4c0 sound/core/seq/oss/seq_oss_synth.c:281
[<
ffffffff8501b0a8>] snd_seq_oss_open+0x748/0x8d0 sound/core/seq/oss/seq_oss_init.c:274
[<
ffffffff85019d8a>] odev_open+0x6a/0x90 sound/core/seq/oss/seq_oss.c:138
[<
ffffffff84f7040f>] soundcore_open+0x30f/0x640 sound/sound_core.c:639
......
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&grp->list_mutex);
lock(register_mutex#5);
lock(&grp->list_mutex);
lock(register_mutex#5);
*** DEADLOCK ***
======================================================
The fix is to simply move the registration parts in
snd_rawmidi_dev_register() to the outside of the register_mutex lock.
The lock is needed only to manage the linked list, and it's not
necessarily to cover the whole initialization process.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Takashi Iwai [Wed, 7 Sep 2016 13:45:31 +0000 (15:45 +0200)]
ALSA: timer: Fix zero-division by continue of uninitialized instance
When a user timer instance is continued without the explicit start
beforehand, the system gets eventually zero-division error like:
divide error: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN
CPU: 1 PID: 27320 Comm: syz-executor Not tainted 4.8.0-rc3-next-
20160825+ #8
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS Bochs 01/01/2011
task:
ffff88003c9b2280 task.stack:
ffff880027280000
RIP: 0010:[<
ffffffff858e1a6c>] [< inline >] ktime_divns include/linux/ktime.h:195
RIP: 0010:[<
ffffffff858e1a6c>] [<
ffffffff858e1a6c>] snd_hrtimer_callback+0x1bc/0x3c0 sound/core/hrtimer.c:62
Call Trace:
<IRQ>
[< inline >] __run_hrtimer kernel/time/hrtimer.c:1238
[<
ffffffff81504335>] __hrtimer_run_queues+0x325/0xe70 kernel/time/hrtimer.c:1302
[<
ffffffff81506ceb>] hrtimer_interrupt+0x18b/0x420 kernel/time/hrtimer.c:1336
[<
ffffffff8126d8df>] local_apic_timer_interrupt+0x6f/0xe0 arch/x86/kernel/apic/apic.c:933
[<
ffffffff86e13056>] smp_apic_timer_interrupt+0x76/0xa0 arch/x86/kernel/apic/apic.c:957
[<
ffffffff86e1210c>] apic_timer_interrupt+0x8c/0xa0 arch/x86/entry/entry_64.S:487
<EOI>
.....
Although a similar issue was spotted and a fix patch was merged in
commit [
6b760bb2c63a: ALSA: timer: fix division by zero after
SNDRV_TIMER_IOCTL_CONTINUE], it seems covering only a part of
iceberg.
In this patch, we fix the issue a bit more drastically. Basically the
continue of an uninitialized timer is supposed to be a fresh start, so
we do it for user timers. For the direct snd_timer_continue() call,
there is no way to pass the initial tick value, so we kick out for the
uninitialized case.
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allen Hung [Fri, 15 Jul 2016 09:42:22 +0000 (17:42 +0800)]
dmi-id: don't free dev structure after calling device_register
dmi_dev is freed in error exit code but, according to the document
of device_register, it should never directly free device structure
after calling this function, even if it returned an error! Use
put_device() instead.
Signed-off-by: Allen Hung <allen_hung@dell.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Mathias Nyman [Wed, 7 Sep 2016 14:26:33 +0000 (17:26 +0300)]
xhci: fix null pointer dereference in stop command timeout function
The stop endpoint command has its own 5 second timeout timer.
If the timeout function is triggered between USB3 and USB2 host
removal it will try to call usb_hc_died(xhci_to_hcd(xhci)->primary_hcd)
the ->primary_hcd will be set to NULL at USB3 hcd removal.
Fix this by first checking if the PCI host is being removed, and
also by using only xhci_to_hcd() as it will always return the primary
hcd.
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Linus Torvalds [Thu, 8 Sep 2016 04:28:26 +0000 (21:28 -0700)]
Merge branch 'for-rc' of git://git./linux/kernel/git/rzhang/linux
Pull thermal fix from Zhang Rui:
"Only one patch this time, which fixes a crash in rcar_thermal driver.
From Dirk Behme"
* 'for-rc' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
thermal: rcar_thermal: Fix priv->zone error handling
This page took 0.055363 seconds and 5 git commands to generate.