--- /dev/null
+SMSC USB4604 High-Speed Hub Controller
+
+Required properties:
+- compatible: Should be "smsc,usb4604"
+
+Optional properties:
+- reg: Specifies the i2c slave address, it is required and should be 0x2d
+ if I2C is used.
+- reset-gpios: Should specify GPIO for reset.
+- initial-mode: Should specify initial mode.
+ (1 for HUB mode, 2 for STANDBY mode)
+
+Examples:
+ usb-hub@2d {
+ compatible = "smsc,usb4604";
+ reg = <0x2d>;
+ reset-gpios = <&gpx3 5 1>;
+ initial-mode = <1>;
+ };
F: drivers/net/usb/lan78xx.*
USB MASS STORAGE DRIVER
-M: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
+M: Alan Stern <stern@rowland.harvard.edu>
L: linux-usb@vger.kernel.org
L: usb-storage@lists.one-eyed-alien.net
S: Maintained
LEDs and you want to use them as activity indicators for USB host or
gadget.
+config USB_ULPI_BUS
+ tristate "USB ULPI PHY interface support"
+ depends on USB_COMMON
+ help
+ UTMI+ Low Pin Interface (ULPI) is specification for a commonly used
+ USB 2.0 PHY interface. The ULPI specification defines a standard set
+ of registers that can be used to detect the vendor and product which
+ allows ULPI to be handled as a bus. This module is the driver for that
+ bus.
+
+ The ULPI interfaces (the buses) are registered by the drivers for USB
+ controllers which support ULPI register access and have ULPI PHY
+ attached to them. The ULPI PHY drivers themselves are normal PHY
+ drivers.
+
+ ULPI PHYs provide often functions such as ADP sensing/probing (OTG
+ protocol) and USB charger detection.
+
+ To compile this driver as a module, choose M here: the module will
+ be called ulpi.
+
endif # USB_SUPPORT
/* instance init */
instance = kzalloc(sizeof(*instance), GFP_KERNEL);
- if (!instance) {
- usb_dbg(usbatm_instance, "cxacru_bind: no memory for instance data\n");
+ if (!instance)
return -ENOMEM;
- }
instance->usbatm = usbatm_instance;
instance->modem_type = (struct cxacru_modem_type *) id->driver_info;
}
instance->rcv_urb = usb_alloc_urb(0, GFP_KERNEL);
if (!instance->rcv_urb) {
- usb_dbg(usbatm_instance, "cxacru_bind: no memory for rcv_urb\n");
ret = -ENOMEM;
goto fail;
}
instance->snd_urb = usb_alloc_urb(0, GFP_KERNEL);
if (!instance->snd_urb) {
- usb_dbg(usbatm_instance, "cxacru_bind: no memory for snd_urb\n");
ret = -ENOMEM;
goto fail;
}
instance = kzalloc(sizeof(*instance), GFP_KERNEL);
if (!instance) {
- usb_err(usbatm, "%s: no memory for instance data!\n", __func__);
ret = -ENOMEM;
goto fail_release;
}
load_XILINX_firmware(sc);
intr = kmalloc(size, GFP_KERNEL);
- if (!intr) {
- uea_err(INS_TO_USBDEV(sc),
- "cannot allocate interrupt package\n");
+ if (!intr)
goto err0;
- }
sc->urb_int = usb_alloc_urb(0, GFP_KERNEL);
- if (!sc->urb_int) {
- uea_err(INS_TO_USBDEV(sc), "cannot allocate interrupt URB\n");
+ if (!sc->urb_int)
goto err1;
- }
usb_fill_int_urb(sc->urb_int, sc->usb_dev,
usb_rcvintpipe(sc->usb_dev, UEA_INTR_PIPE),
}
sc = kzalloc(sizeof(struct uea_softc), GFP_KERNEL);
- if (!sc) {
- uea_err(usb, "uea_init: not enough memory !\n");
+ if (!sc)
return -ENOMEM;
- }
sc->usb_dev = usb;
usbatm->driver_data = sc;
new = kzalloc(sizeof(struct usbatm_vcc_data), GFP_KERNEL);
if (!new) {
- atm_err(instance, "%s: no memory for vcc_data!\n", __func__);
ret = -ENOMEM;
goto fail;
}
/* instance init */
instance = kzalloc(sizeof(*instance) + sizeof(struct urb *) * (num_rcv_urbs + num_snd_urbs), GFP_KERNEL);
- if (!instance) {
- dev_err(dev, "%s: no memory for instance data!\n", __func__);
+ if (!instance)
return -ENOMEM;
- }
/* public fields */
urb = usb_alloc_urb(iso_packets, GFP_KERNEL);
if (!urb) {
- dev_err(dev, "%s: no memory for urb %d!\n", __func__, i);
error = -ENOMEM;
goto fail_unbind;
}
/* zero the tx padding to avoid leaking information */
buffer = kzalloc(channel->buf_size, GFP_KERNEL);
if (!buffer) {
- dev_err(dev, "%s: no memory for buffer %d!\n", __func__, i);
error = -ENOMEM;
goto fail_unbind;
}
instance->cell_buf = kmalloc(instance->rx_channel.stride, GFP_KERNEL);
if (!instance->cell_buf) {
- dev_err(dev, "%s: no memory for cell buffer!\n", __func__);
error = -ENOMEM;
goto fail_unbind;
}
struct acm *acm;
int retval;
- dev_dbg(tty->dev, "%s\n", __func__);
-
acm = acm_get_by_minor(tty->index);
if (!acm)
return -ENODEV;
{
struct acm *acm = tty->driver_data;
- dev_dbg(tty->dev, "%s\n", __func__);
-
return tty_port_open(&acm->port, tty, filp);
}
int retval = -ENODEV;
int i;
- dev_dbg(&acm->control->dev, "%s\n", __func__);
-
mutex_lock(&acm->mutex);
if (acm->disconnected)
goto disconnected;
{
struct acm *acm = container_of(port, struct acm, port);
- dev_dbg(&acm->control->dev, "%s\n", __func__);
-
acm_release_minor(acm);
usb_put_intf(acm->control);
kfree(acm->country_codes);
struct acm_wb *wb;
int i;
- dev_dbg(&acm->control->dev, "%s\n", __func__);
-
/*
* Need to grab write_lock to prevent race with resume, but no need to
* hold it due to the tty-port initialised flag.
static void acm_tty_cleanup(struct tty_struct *tty)
{
struct acm *acm = tty->driver_data;
- dev_dbg(&acm->control->dev, "%s\n", __func__);
+
tty_port_put(&acm->port);
}
static void acm_tty_hangup(struct tty_struct *tty)
{
struct acm *acm = tty->driver_data;
- dev_dbg(&acm->control->dev, "%s\n", __func__);
+
tty_port_hangup(&acm->port);
}
static void acm_tty_close(struct tty_struct *tty, struct file *filp)
{
struct acm *acm = tty->driver_data;
- dev_dbg(&acm->control->dev, "%s\n", __func__);
+
tty_port_close(&acm->port, tty, filp);
}
{
int i;
- dev_dbg(&acm->control->dev, "%s\n", __func__);
-
usb_kill_urb(acm->ctrlurb);
for (i = 0; i < ACM_NW; i++)
usb_kill_urb(acm->wb[i].urb);
struct tty_struct *tty;
int i;
- dev_dbg(&intf->dev, "%s\n", __func__);
-
/* sibling interface is already cleaning up */
if (!acm)
return;
#define WDM_SUSPENDING 8
#define WDM_RESETTING 9
#define WDM_OVERFLOW 10
+#define WDM_DRAIN_ON_OPEN 11
#define WDM_MAX 16
wake_up(&desc->wait);
}
+/* forward declaration */
+static int service_outstanding_interrupt(struct wdm_device *desc);
+
static void wdm_in_callback(struct urb *urb)
{
struct wdm_device *desc = urb->context;
switch (status) {
case -ENOENT:
dev_dbg(&desc->intf->dev,
- "nonzero urb status received: -ENOENT");
+ "nonzero urb status received: -ENOENT\n");
goto skip_error;
case -ECONNRESET:
dev_dbg(&desc->intf->dev,
- "nonzero urb status received: -ECONNRESET");
+ "nonzero urb status received: -ECONNRESET\n");
goto skip_error;
case -ESHUTDOWN:
dev_dbg(&desc->intf->dev,
- "nonzero urb status received: -ESHUTDOWN");
+ "nonzero urb status received: -ESHUTDOWN\n");
goto skip_error;
case -EPIPE:
- dev_err(&desc->intf->dev,
+ dev_dbg(&desc->intf->dev,
"nonzero urb status received: -EPIPE\n");
break;
default:
}
}
- desc->rerr = status;
+ /*
+ * only set a new error if there is no previous error.
+ * Errors are only cleared during read/open
+ */
+ if (desc->rerr == 0)
+ desc->rerr = status;
+
if (length + desc->length > desc->wMaxCommand) {
/* The buffer would overflow */
set_bit(WDM_OVERFLOW, &desc->flags);
desc->reslength = length;
}
}
+
+ /*
+ * Handling devices with the WDM_DRAIN_ON_OPEN flag set:
+ * If desc->resp_count is unset, then the urb was submitted
+ * without a prior notification. If the device returned any
+ * data, then this implies that it had messages queued without
+ * notifying us. Continue reading until that queue is flushed.
+ */
+ if (!desc->resp_count) {
+ if (!length) {
+ /* do not propagate the expected -EPIPE */
+ desc->rerr = 0;
+ goto unlock;
+ }
+ dev_dbg(&desc->intf->dev, "got %d bytes without notification\n", length);
+ set_bit(WDM_RESPONDING, &desc->flags);
+ usb_submit_urb(desc->response, GFP_ATOMIC);
+ }
+
skip_error:
+ set_bit(WDM_READ, &desc->flags);
wake_up(&desc->wait);
- set_bit(WDM_READ, &desc->flags);
+ if (desc->rerr) {
+ /*
+ * Since there was an error, userspace may decide to not read
+ * any data after poll'ing.
+ * We should respond to further attempts from the device to send
+ * data, so that we can get unstuck.
+ */
+ service_outstanding_interrupt(desc);
+ }
+
+unlock:
spin_unlock(&desc->iuspin);
}
switch (dr->bNotificationType) {
case USB_CDC_NOTIFY_RESPONSE_AVAILABLE:
dev_dbg(&desc->intf->dev,
- "NOTIFY_RESPONSE_AVAILABLE received: index %d len %d",
+ "NOTIFY_RESPONSE_AVAILABLE received: index %d len %d\n",
le16_to_cpu(dr->wIndex), le16_to_cpu(dr->wLength));
break;
case USB_CDC_NOTIFY_NETWORK_CONNECTION:
dev_dbg(&desc->intf->dev,
- "NOTIFY_NETWORK_CONNECTION %s network",
+ "NOTIFY_NETWORK_CONNECTION %s network\n",
dr->wValue ? "connected to" : "disconnected from");
goto exit;
case USB_CDC_NOTIFY_SPEED_CHANGE:
- dev_dbg(&desc->intf->dev, "SPEED_CHANGE received (len %u)",
+ dev_dbg(&desc->intf->dev, "SPEED_CHANGE received (len %u)\n",
urb->actual_length);
goto exit;
default:
&& !test_bit(WDM_DISCONNECTING, &desc->flags)
&& !test_bit(WDM_SUSPENDING, &desc->flags)) {
rv = usb_submit_urb(desc->response, GFP_ATOMIC);
- dev_dbg(&desc->intf->dev, "%s: usb_submit_urb %d",
- __func__, rv);
+ dev_dbg(&desc->intf->dev, "submit response URB %d\n", rv);
}
spin_unlock(&desc->iuspin);
if (rv < 0) {
rv = usb_translate_errors(rv);
goto out_free_mem_pm;
} else {
- dev_dbg(&desc->intf->dev, "Tx URB has been submitted index=%d",
+ dev_dbg(&desc->intf->dev, "Tx URB has been submitted index=%d\n",
le16_to_cpu(req->wIndex));
}
}
/*
- * clear WDM_READ flag and possibly submit the read urb if resp_count
- * is non-zero.
+ * Submit the read urb if resp_count is non-zero.
*
* Called with desc->iuspin locked
*/
-static int clear_wdm_read_flag(struct wdm_device *desc)
+static int service_outstanding_interrupt(struct wdm_device *desc)
{
int rv = 0;
- clear_bit(WDM_READ, &desc->flags);
-
/* submit read urb only if the device is waiting for it */
if (!desc->resp_count || !--desc->resp_count)
goto out;
}
if (!desc->reslength) { /* zero length read */
- dev_dbg(&desc->intf->dev, "%s: zero length - clearing WDM_READ\n", __func__);
- rv = clear_wdm_read_flag(desc);
+ dev_dbg(&desc->intf->dev, "zero length - clearing WDM_READ\n");
+ clear_bit(WDM_READ, &desc->flags);
+ rv = service_outstanding_interrupt(desc);
spin_unlock_irq(&desc->iuspin);
if (rv < 0)
goto err;
desc->length -= cntr;
/* in case we had outstanding data */
- if (!desc->length)
- clear_wdm_read_flag(desc);
+ if (!desc->length) {
+ clear_bit(WDM_READ, &desc->flags);
+ service_outstanding_interrupt(desc);
+ }
spin_unlock_irq(&desc->iuspin);
rv = cntr;
dev_err(&desc->intf->dev,
"Error submitting int urb - %d\n", rv);
rv = usb_translate_errors(rv);
+ } else if (test_bit(WDM_DRAIN_ON_OPEN, &desc->flags)) {
+ /*
+ * Some devices keep pending messages queued
+ * without resending notifications. We must
+ * flush the message queue before we can
+ * assume a one-to-one relationship between
+ * notifications and messages in the queue
+ */
+ dev_dbg(&desc->intf->dev, "draining queued data\n");
+ set_bit(WDM_RESPONDING, &desc->flags);
+ rv = usb_submit_urb(desc->response, GFP_KERNEL);
}
} else {
rv = 0;
if (!desc->count) {
if (!test_bit(WDM_DISCONNECTING, &desc->flags)) {
- dev_dbg(&desc->intf->dev, "wdm_release: cleanup");
+ dev_dbg(&desc->intf->dev, "wdm_release: cleanup\n");
kill_urbs(desc);
spin_lock_irq(&desc->iuspin);
desc->resp_count = 0;
/* --- hotplug --- */
static int wdm_create(struct usb_interface *intf, struct usb_endpoint_descriptor *ep,
- u16 bufsize, int (*manage_power)(struct usb_interface *, int))
+ u16 bufsize, int (*manage_power)(struct usb_interface *, int),
+ bool drain_on_open)
{
int rv = -ENOMEM;
struct wdm_device *desc;
desc->manage_power = manage_power;
+ /*
+ * "drain_on_open" enables a hack to work around a firmware
+ * issue observed on network functions, in particular MBIM
+ * functions.
+ *
+ * Quoting section 7 of the CDC-WMC r1.1 specification:
+ *
+ * "The firmware shall interpret GetEncapsulatedResponse as a
+ * request to read response bytes. The firmware shall send
+ * the next wLength bytes from the response. The firmware
+ * shall allow the host to retrieve data using any number of
+ * GetEncapsulatedResponse requests. The firmware shall
+ * return a zero- length reply if there are no data bytes
+ * available.
+ *
+ * The firmware shall send ResponseAvailable notifications
+ * periodically, using any appropriate algorithm, to inform
+ * the host that there is data available in the reply
+ * buffer. The firmware is allowed to send ResponseAvailable
+ * notifications even if there is no data available, but
+ * this will obviously reduce overall performance."
+ *
+ * These requirements, although they make equally sense, are
+ * often not implemented by network functions. Some firmwares
+ * will queue data indefinitely, without ever resending a
+ * notification. The result is that the driver and firmware
+ * loses "syncronization" if the driver ever fails to respond
+ * to a single notification, something which easily can happen
+ * on release(). When this happens, the driver will appear to
+ * never receive notifications for the most current data. Each
+ * notification will only cause a single read, which returns
+ * the oldest data in the firmware's queue.
+ *
+ * The "drain_on_open" hack resolves the situation by draining
+ * data from the firmware until none is returned, without a
+ * prior notification.
+ *
+ * This will inevitably race with the firmware, risking that
+ * we read data from the device before handling the associated
+ * notification. To make things worse, some of the devices
+ * needing the hack do not implement the "return zero if no
+ * data is available" requirement either. Instead they return
+ * an error on the subsequent read in this case. This means
+ * that "winning" the race can cause an unexpected EIO to
+ * userspace.
+ *
+ * "winning" the race is more likely on resume() than on
+ * open(), and the unexpected error is more harmful in the
+ * middle of an open session. The hack is therefore only
+ * applied on open(), and not on resume() where it logically
+ * would be equally necessary. So we define open() as the only
+ * driver <-> device "syncronization point". Should we happen
+ * to lose a notification after open(), then syncronization
+ * will be lost until release()
+ *
+ * The hack should not be enabled for CDC WDM devices
+ * conforming to the CDC-WMC r1.1 specification. This is
+ * ensured by setting drain_on_open to false in wdm_probe().
+ */
+ if (drain_on_open)
+ set_bit(WDM_DRAIN_ON_OPEN, &desc->flags);
+
spin_lock(&wdm_device_list_lock);
list_add(&desc->device_list, &wdm_device_list);
spin_unlock(&wdm_device_list_lock);
goto err;
ep = &iface->endpoint[0].desc;
- rv = wdm_create(intf, ep, maxcom, &wdm_manage_power);
+ rv = wdm_create(intf, ep, maxcom, &wdm_manage_power, false);
err:
return rv;
{
int rv = -EINVAL;
- rv = wdm_create(intf, ep, bufsize, manage_power);
+ rv = wdm_create(intf, ep, bufsize, manage_power, true);
if (rv < 0)
goto err;
if (!desc->count)
cleanup(desc);
else
- dev_dbg(&intf->dev, "%s: %d open files - postponing cleanup\n", __func__, desc->count);
+ dev_dbg(&intf->dev, "%d open files - postponing cleanup\n", desc->count);
mutex_unlock(&wdm_mutex);
}
if (data->iin_ep_present) {
/* allocate int urb */
data->iin_urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!data->iin_urb) {
- dev_err(&intf->dev, "Failed to allocate int urb\n");
+ if (!data->iin_urb)
goto error_register;
- }
/* will reference data in int urb */
kref_get(&data->kref);
/* allocate buffer for interrupt in */
data->iin_buffer = kmalloc(data->iin_wMaxPacketSize,
GFP_KERNEL);
- if (!data->iin_buffer) {
- dev_err(&intf->dev, "Failed to allocate int buf\n");
+ if (!data->iin_buffer)
goto error_register;
- }
/* fill interrupt urb */
usb_fill_int_urb(data->iin_urb, data->usb_dev,
*
* Registers a driver with the ULPI bus.
*/
-int ulpi_register_driver(struct ulpi_driver *drv)
+int __ulpi_register_driver(struct ulpi_driver *drv, struct module *module)
{
if (!drv->probe)
return -EINVAL;
+ drv->driver.owner = module;
drv->driver.bus = &ulpi_bus;
return driver_register(&drv->driver);
}
-EXPORT_SYMBOL_GPL(ulpi_register_driver);
+EXPORT_SYMBOL_GPL(__ulpi_register_driver);
/**
* ulpi_unregister_driver - unregister a driver with the ULPI bus
help
Implements OTG Finite State Machine as specified in On-The-Go
and Embedded Host Supplement to the USB Revision 2.0 Specification.
-
-config USB_ULPI_BUS
- tristate "USB ULPI PHY interface support"
- depends on USB_SUPPORT
- help
- UTMI+ Low Pin Interface (ULPI) is specification for a commonly used
- USB 2.0 PHY interface. The ULPI specification defines a standard set
- of registers that can be used to detect the vendor and product which
- allows ULPI to be handled as a bus. This module is the driver for that
- bus.
-
- The ULPI interfaces (the buses) are registered by the drivers for USB
- controllers which support ULPI register access and have ULPI PHY
- attached to them. The ULPI PHY drivers themselves are normal PHY
- drivers.
-
- ULPI PHYs provide often functions such as ADP sensing/probing (OTG
- protocol) and USB charger detection.
-
- To compile this driver as a module, choose M here: the module will
- be called ulpi.
usbcore-y := usb.o hub.o hcd.o urb.o message.o driver.o
usbcore-y += config.o file.o buffer.o sysfs.o endpoint.o
usbcore-y += devio.o notify.o generic.o quirks.o devices.o
-usbcore-y += port.o of.o
+usbcore-y += port.o
+usbcore-$(CONFIG_OF) += of.o
usbcore-$(CONFIG_PCI) += hcd-pci.o
usbcore-$(CONFIG_ACPI) += usb-acpi.o
struct usb_hcd *hcd;
hcd = kzalloc(sizeof(*hcd) + driver->hcd_priv_size, GFP_KERNEL);
- if (!hcd) {
- dev_dbg (dev, "hcd alloc failed\n");
+ if (!hcd)
return NULL;
- }
if (primary_hcd == NULL) {
hcd->address0_mutex = kmalloc(sizeof(*hcd->address0_mutex),
GFP_KERNEL);
/*-------------------------------------------------------------------------*/
-#if defined(CONFIG_USB_MON) || defined(CONFIG_USB_MON_MODULE)
+#if IS_ENABLED(CONFIG_USB_MON)
const struct usb_mon_operations *mon_ops;
dev_info(&intf->dev, "USB hub found\n");
hub = kzalloc(sizeof(*hub), GFP_KERNEL);
- if (!hub) {
- dev_dbg(&intf->dev, "couldn't kmalloc hub struct\n");
+ if (!hub)
return -ENOMEM;
- }
kref_init(&hub->kref);
hub->intfdev = &intf->dev;
}
buf = kmalloc(len, GFP_NOIO);
- if (buf == NULL) {
- dev_err(&udev->dev, "no mem to re-read configs after reset\n");
+ if (!buf)
/* assume the worst */
return 1;
- }
+
for (index = 0; index < udev->descriptor.bNumConfigurations; index++) {
old_length = le16_to_cpu(udev->config[index].desc.wTotalLength);
length = usb_get_descriptor(udev, USB_DT_CONFIG, index, buf,
nintf = cp->desc.bNumInterfaces;
new_interfaces = kmalloc(nintf * sizeof(*new_interfaces),
GFP_NOIO);
- if (!new_interfaces) {
- dev_err(&dev->dev, "Out of memory\n");
+ if (!new_interfaces)
return -ENOMEM;
- }
for (; n < nintf; ++n) {
new_interfaces[n] = kzalloc(
sizeof(struct usb_interface),
GFP_NOIO);
if (!new_interfaces[n]) {
- dev_err(&dev->dev, "Out of memory\n");
ret = -ENOMEM;
free_interfaces:
while (--n >= 0)
*/
#include <linux/of.h>
+#include <linux/usb/of.h>
/**
* usb_of_get_child_node - Find the device node match port number
{ USB_DEVICE(0x0525, 0xa4a2), },
#endif
-#if defined(CONFIG_USB_TEST) || defined(CONFIG_USB_TEST_MODULE)
+#if IS_ENABLED(CONFIG_USB_TEST)
/* gadget zero, for testing */
{ USB_DEVICE(0x0525, 0xa4a0), },
#endif
urb = kmalloc(sizeof(struct urb) +
iso_packets * sizeof(struct usb_iso_packet_descriptor),
mem_flags);
- if (!urb) {
- printk(KERN_ERR "alloc_urb: kmalloc failed\n");
+ if (!urb)
return NULL;
- }
usb_init_urb(urb);
return urb;
}
hsotg->ctrl_buff = devm_kzalloc(hsotg->dev,
DWC2_CTRL_BUFF_SIZE, GFP_KERNEL);
- if (!hsotg->ctrl_buff) {
- dev_err(dev, "failed to allocate ctrl request buff\n");
+ if (!hsotg->ctrl_buff)
return -ENOMEM;
- }
hsotg->ep0_buff = devm_kzalloc(hsotg->dev,
DWC2_CTRL_BUFF_SIZE, GFP_KERNEL);
- if (!hsotg->ep0_buff) {
- dev_err(dev, "failed to allocate ctrl reply buff\n");
+ if (!hsotg->ep0_buff)
return -ENOMEM;
- }
ret = devm_request_irq(hsotg->dev, irq, dwc2_hsotg_irq, IRQF_SHARED,
dev_name(hsotg->dev), hsotg);
/* Create new workqueue and init work */
retval = -ENOMEM;
- hsotg->wq_otg = create_singlethread_workqueue("dwc2");
+ hsotg->wq_otg = alloc_ordered_workqueue("dwc2", 0);
if (!hsotg->wq_otg) {
dev_err(hsotg->dev, "Failed to create workqueue\n");
goto error2;
config USB_DWC3
tristate "DesignWare USB3 DRD Core Support"
depends on (USB || USB_GADGET) && HAS_DMA
- select USB_XHCI_PLATFORM if USB_SUPPORT && USB_XHCI_HCD
+ select USB_XHCI_PLATFORM if USB_XHCI_HCD
help
Say Y or M here if your system has a Dual Role SuperSpeed
USB controller based on the DesignWare USB3 IP Core.
bd = ep->rxbase;
ep->rxframe = kmalloc(sizeof(*ep->rxframe), GFP_ATOMIC);
- if (ep->rxframe == NULL) {
- dev_err(ep->udc->dev, "malloc rxframe failed\n");
+ if (!ep->rxframe)
return -ENOMEM;
- }
qe_frame_init(ep->rxframe);
size = (ep->ep.maxpacket + USB_CRC_SIZE + 2) * (bdring_len + 1);
ep->rxbuffer = kzalloc(size, GFP_ATOMIC);
- if (ep->rxbuffer == NULL) {
- dev_err(ep->udc->dev, "malloc rxbuffer failed,size=%d\n",
- size);
+ if (!ep->rxbuffer) {
kfree(ep->rxframe);
return -ENOMEM;
}
if ((ep->tm == USBP_TM_CTL) || (ep->dir == USB_DIR_IN)) {
ep->txframe = kmalloc(sizeof(*ep->txframe), GFP_ATOMIC);
- if (ep->txframe == NULL) {
- dev_err(udc->dev, "malloc txframe failed\n");
+ if (!ep->txframe)
goto en_done2;
- }
qe_frame_init(ep->txframe);
}
u32 offset;
udc = kzalloc(sizeof(*udc), GFP_KERNEL);
- if (udc == NULL) {
- dev_err(&ofdev->dev, "malloc udc failed\n");
+ if (!udc)
goto cleanup;
- }
udc->dev = &ofdev->dev;
/* alloc, and start init */
dev = kzalloc (sizeof *dev, GFP_KERNEL);
- if (dev == NULL){
- pr_debug("enomem %s\n", pci_name(pdev));
+ if (!dev) {
retval = -ENOMEM;
goto err;
}
xceiv = NULL;
/* "udc" is now valid */
pullup_disable(udc);
-#if defined(CONFIG_USB_OHCI_HCD) || defined(CONFIG_USB_OHCI_HCD_MODULE)
+#if IS_ENABLED(CONFIG_USB_OHCI_HCD)
udc->gadget.is_otg = (config->otg != 0);
#endif
udc = ep->udc;
req = kzalloc(sizeof(*req), gfp_flags);
- if (!req) {
- dev_err(udc->dev, "%s:not enough memory", __func__);
+ if (!req)
return NULL;
- }
req->ep = ep;
INIT_LIST_HEAD(&req->queue);
#include <linux/slab.h>
#include <linux/of.h>
#include <linux/of_gpio.h>
+#include <linux/of_platform.h>
#include <linux/usb/ehci_pdriver.h>
#include <linux/usb/ohci_pdriver.h>
MODULE_DESCRIPTION("Common USB driver for BCMA Bus");
MODULE_LICENSE("GPL");
+/* See BCMA_CLKCTLST_EXTRESREQ and BCMA_CLKCTLST_EXTRESST */
+#define USB_BCMA_CLKCTLST_USB_CLK_REQ 0x00000100
+
struct bcma_hcd_device {
struct bcma_device *core;
struct platform_device *ehci_dev;
}
}
+/**
+ * bcma_hcd_usb20_old_arm_init - Initialize old USB 2.0 controller on ARM
+ *
+ * Old USB 2.0 core is identified as BCMA_CORE_USB20_HOST and was introduced
+ * long before Northstar devices. It seems some cheaper chipsets like BCM53573
+ * still use it.
+ * Initialization of this old core differs between MIPS and ARM.
+ */
+static int bcma_hcd_usb20_old_arm_init(struct bcma_hcd_device *usb_dev)
+{
+ struct bcma_device *core = usb_dev->core;
+ struct device *dev = &core->dev;
+ struct bcma_device *pmu_core;
+
+ usleep_range(10000, 20000);
+ if (core->id.rev < 5)
+ return 0;
+
+ pmu_core = bcma_find_core(core->bus, BCMA_CORE_PMU);
+ if (!pmu_core) {
+ dev_err(dev, "Could not find PMU core\n");
+ return -ENOENT;
+ }
+
+ /* Take USB core out of reset */
+ bcma_awrite32(core, BCMA_IOCTL, BCMA_IOCTL_CLK | BCMA_IOCTL_FGC);
+ usleep_range(100, 200);
+ bcma_awrite32(core, BCMA_RESET_CTL, BCMA_RESET_CTL_RESET);
+ usleep_range(100, 200);
+ bcma_awrite32(core, BCMA_RESET_CTL, 0);
+ usleep_range(100, 200);
+ bcma_awrite32(core, BCMA_IOCTL, BCMA_IOCTL_CLK);
+ usleep_range(100, 200);
+
+ /* Enable Misc PLL */
+ bcma_write32(core, BCMA_CLKCTLST, BCMA_CLKCTLST_FORCEHT |
+ BCMA_CLKCTLST_HQCLKREQ |
+ USB_BCMA_CLKCTLST_USB_CLK_REQ);
+ usleep_range(100, 200);
+
+ bcma_write32(core, 0x510, 0xc7f85000);
+ bcma_write32(core, 0x510, 0xc7f85003);
+ usleep_range(300, 600);
+
+ /* Program USB PHY PLL parameters */
+ bcma_write32(pmu_core, BCMA_CC_PMU_PLLCTL_ADDR, 0x6);
+ bcma_write32(pmu_core, BCMA_CC_PMU_PLLCTL_DATA, 0x005360c1);
+ usleep_range(100, 200);
+ bcma_write32(pmu_core, BCMA_CC_PMU_PLLCTL_ADDR, 0x7);
+ bcma_write32(pmu_core, BCMA_CC_PMU_PLLCTL_DATA, 0x0);
+ usleep_range(100, 200);
+ bcma_set32(pmu_core, BCMA_CC_PMU_CTL, BCMA_CC_PMU_CTL_PLL_UPD);
+ usleep_range(100, 200);
+
+ bcma_write32(core, 0x510, 0x7f8d007);
+ udelay(1000);
+
+ /* Take controller out of reset */
+ bcma_write32(core, 0x200, 0x4ff);
+ usleep_range(25, 50);
+ bcma_write32(core, 0x200, 0x6ff);
+ usleep_range(25, 50);
+ bcma_write32(core, 0x200, 0x7ff);
+ usleep_range(25, 50);
+
+ of_platform_default_populate(dev->of_node, NULL, dev);
+
+ return 0;
+}
+
static void bcma_hcd_init_chip_arm_phy(struct bcma_device *dev)
{
struct bcma_device *arm_core;
return err;
}
+static int bcma_hcd_usb30_init(struct bcma_hcd_device *bcma_hcd)
+{
+ struct bcma_device *core = bcma_hcd->core;
+ struct device *dev = &core->dev;
+
+ bcma_core_enable(core, 0);
+
+ of_platform_default_populate(dev->of_node, NULL, dev);
+
+ return 0;
+}
+
static int bcma_hcd_probe(struct bcma_device *core)
{
int err;
switch (core->id.id) {
case BCMA_CORE_USB20_HOST:
+ if (IS_ENABLED(CONFIG_ARM))
+ err = bcma_hcd_usb20_old_arm_init(usb_dev);
+ else if (IS_ENABLED(CONFIG_MIPS))
+ err = bcma_hcd_usb20_init(usb_dev);
+ else
+ err = -ENOTSUPP;
+ break;
case BCMA_CORE_NS_USB20:
err = bcma_hcd_usb20_init(usb_dev);
- if (err)
- return err;
+ break;
+ case BCMA_CORE_NS_USB30:
+ err = bcma_hcd_usb30_init(usb_dev);
break;
default:
return -ENODEV;
}
+ if (err)
+ return err;
bcma_set_drvdata(core, usb_dev);
return 0;
static const struct bcma_device_id bcma_hcd_table[] = {
BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_USB20_HOST, BCMA_ANY_REV, BCMA_ANY_CLASS),
BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_NS_USB20, BCMA_ANY_REV, BCMA_ANY_CLASS),
+ BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_NS_USB30, BCMA_ANY_REV, BCMA_ANY_CLASS),
{},
};
MODULE_DEVICE_TABLE(bcma, bcma_hcd_table);
#include "ehci.h"
#define DRIVER_DESC "EHCI generic platform driver"
-#define EHCI_MAX_CLKS 3
+#define EHCI_MAX_CLKS 4
#define EHCI_MAX_RSTS 3
#define hcd_to_ehci_priv(h) ((struct ehci_platform_priv *)hcd_to_ehci(h)->priv)
/* allocate memory for SCC data structure */
usb = kzalloc(sizeof(*usb), GFP_KERNEL);
- if (!usb) {
- fhci_err(fhci, "no memory for SCC data struct\n");
+ if (!usb)
return NULL;
- }
usb->fhci = fhci;
usb->hc_list = fhci->hc_list;
pdata->controller_ver = usb_get_ver_info(np);
/* Activate Erratum by reading property in device tree */
- if (of_get_property(np, "fsl,usb-erratum-a007792", NULL))
- pdata->has_fsl_erratum_a007792 = 1;
- else
- pdata->has_fsl_erratum_a007792 = 0;
- if (of_get_property(np, "fsl,usb-erratum-a005275", NULL))
- pdata->has_fsl_erratum_a005275 = 1;
- else
- pdata->has_fsl_erratum_a005275 = 0;
+ pdata->has_fsl_erratum_a007792 =
+ of_property_read_bool(np, "fsl,usb-erratum-a007792");
+ pdata->has_fsl_erratum_a005275 =
+ of_property_read_bool(np, "fsl,usb-erratum-a005275");
/*
* Determine whether phy_clk_valid needs to be checked
* by reading property in device tree
*/
- if (of_get_property(np, "phy-clk-valid", NULL))
- pdata->check_phy_clk_valid = 1;
- else
- pdata->check_phy_clk_valid = 0;
+ pdata->check_phy_clk_valid =
+ of_property_read_bool(np, "phy-clk-valid");
if (pdata->have_sysif_regs) {
if (pdata->controller_ver == FSL_USB_VER_NONE) {
INIT_LIST_HEAD(&max3421_hcd->ep_list);
max3421_hcd->tx = kmalloc(sizeof(*max3421_hcd->tx), GFP_KERNEL);
- if (!max3421_hcd->tx) {
- dev_err(&spi->dev, "failed to kmalloc tx buffer\n");
+ if (!max3421_hcd->tx)
goto error;
- }
max3421_hcd->rx = kmalloc(sizeof(*max3421_hcd->rx), GFP_KERNEL);
- if (!max3421_hcd->rx) {
- dev_err(&spi->dev, "failed to kmalloc rx buffer\n");
+ if (!max3421_hcd->rx)
goto error;
- }
max3421_hcd->spi_thread = kthread_run(max3421_spi_thread, hcd,
"max3421_spi_thread");
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/module.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
#include <linux/usb.h>
#include <linux/usb/hcd.h>
+#include <soc/at91/atmel-sfr.h>
#include "ohci.h"
struct clk *hclk;
bool clocked;
bool wakeup; /* Saved wake-up state for resume */
+ struct regmap *sfr_regmap;
};
/* interface and function clocks; sometimes also an AHB clock */
static void usb_hcd_at91_remove (struct usb_hcd *, struct platform_device *);
+struct regmap *at91_dt_syscon_sfr(void)
+{
+ struct regmap *regmap;
+
+ regmap = syscon_regmap_lookup_by_compatible("atmel,sama5d2-sfr");
+ if (IS_ERR(regmap))
+ regmap = NULL;
+
+ return regmap;
+}
+
/* configure so an HC device and id are always provided */
/* always called with process context; sleeping is OK */
goto err;
}
+ ohci_at91->sfr_regmap = at91_dt_syscon_sfr();
+ if (!ohci_at91->sfr_regmap)
+ dev_warn(dev, "failed to find sfr node\n");
+
board = hcd->self.controller->platform_data;
ohci = hcd_to_ohci(hcd);
ohci->num_ports = board->ports;
return length;
}
+static int ohci_at91_port_suspend(struct regmap *regmap, u8 set)
+{
+ u32 regval;
+ int ret;
+
+ if (!regmap)
+ return 0;
+
+ ret = regmap_read(regmap, AT91_SFR_OHCIICR, ®val);
+ if (ret)
+ return ret;
+
+ if (set)
+ regval |= AT91_OHCIICR_USB_SUSPEND;
+ else
+ regval &= ~AT91_OHCIICR_USB_SUSPEND;
+
+ regmap_write(regmap, AT91_SFR_OHCIICR, regval);
+
+ return 0;
+}
+
/*
* Look at the control requests to the root hub and see if we need to override.
*/
u16 wIndex, char *buf, u16 wLength)
{
struct at91_usbh_data *pdata = dev_get_platdata(hcd->self.controller);
+ struct ohci_at91_priv *ohci_at91 = hcd_to_ohci_at91_priv(hcd);
struct usb_hub_descriptor *desc;
int ret = -EINVAL;
u32 *data = (u32 *)buf;
switch (typeReq) {
case SetPortFeature:
- if (wValue == USB_PORT_FEAT_POWER) {
+ switch (wValue) {
+ case USB_PORT_FEAT_POWER:
dev_dbg(hcd->self.controller, "SetPortFeat: POWER\n");
if (valid_port(wIndex)) {
ohci_at91_usb_set_power(pdata, wIndex, 1);
}
goto out;
+
+ case USB_PORT_FEAT_SUSPEND:
+ dev_dbg(hcd->self.controller, "SetPortFeat: SUSPEND\n");
+ if (valid_port(wIndex)) {
+ ohci_at91_port_suspend(ohci_at91->sfr_regmap,
+ 1);
+ return 0;
+ }
+ break;
}
break;
ohci_at91_usb_set_power(pdata, wIndex, 0);
return 0;
}
+ break;
+
+ case USB_PORT_FEAT_SUSPEND:
+ dev_dbg(hcd->self.controller, "ClearPortFeature: SUSPEND\n");
+ if (valid_port(wIndex)) {
+ ohci_at91_port_suspend(ohci_at91->sfr_regmap,
+ 0);
+ return 0;
+ }
+ break;
}
break;
}
if (ohci_at91->wakeup)
enable_irq_wake(hcd->irq);
+ ohci_at91_port_suspend(ohci_at91->sfr_regmap, 1);
+
ret = ohci_suspend(hcd, ohci_at91->wakeup);
if (ret) {
if (ohci_at91->wakeup)
at91_start_clock(ohci_at91);
ohci_resume(hcd, false);
+
+ ohci_at91_port_suspend(ohci_at91->sfr_regmap, 0);
+
return 0;
}
#include <mach/mux.h>
#include <mach/hardware.h>
-#include <mach/irqs.h>
#include <mach/usb.h>
* This file is licenced under the GPL.
*/
-#include <mach/hardware.h>
#include <asm/mach-types.h>
-#include <mach/assabet.h>
#include <asm/hardware/sa1111.h>
#ifndef CONFIG_SA1111
dev_dbg(&dev->dev, "starting SA-1111 OHCI USB Controller\n");
if (machine_is_xp860() ||
- machine_has_neponset() ||
+ machine_is_assabet() ||
machine_is_pfs168() ||
machine_is_badge4())
usb_rst = USB_RESET_PWRSENSELOW | USB_RESET_PWRCTRLLOW;
uhci->frame_cpu = kcalloc(UHCI_NUMFRAMES, sizeof(*uhci->frame_cpu),
GFP_KERNEL);
- if (!uhci->frame_cpu) {
- dev_err(uhci_dev(uhci),
- "unable to allocate memory for frame pointers\n");
+ if (!uhci->frame_cpu)
goto err_alloc_frame_cpu;
- }
uhci->td_pool = dma_pool_create("uhci_td", uhci_dev(uhci),
sizeof(struct uhci_td), 16, 0);
init_waitqueue_head(&whc->cmd_wq);
init_waitqueue_head(&whc->async_list_wq);
init_waitqueue_head(&whc->periodic_list_wq);
- whc->workqueue = create_singlethread_workqueue(dev_name(&whc->umc->dev));
+ whc->workqueue = alloc_ordered_workqueue(dev_name(&whc->umc->dev), 0);
if (whc->workqueue == NULL) {
ret = -ENOMEM;
goto error;
tegra->phys = devm_kcalloc(&pdev->dev, tegra->num_phys,
sizeof(*tegra->phys), GFP_KERNEL);
if (!tegra->phys) {
- dev_err(&pdev->dev, "failed to allocate PHY array\n");
err = -ENOMEM;
goto put_padctl;
}
xhci->msix_entries =
kmalloc((sizeof(struct msix_entry))*xhci->msix_count,
GFP_KERNEL);
- if (!xhci->msix_entries) {
- xhci_err(xhci, "Failed to allocate MSI-X entries\n");
+ if (!xhci->msix_entries)
return -ENOMEM;
- }
for (i = 0; i < xhci->msix_count; i++) {
xhci->msix_entries[i].entry = i;
help
This option enables support for SMSC USB3503 HSIC to USB 2.0 Driver.
+config USB_HSIC_USB4604
+ tristate "USB4604 HSIC to USB20 Driver"
+ depends on I2C
+ help
+ This option enables support for SMSC USB4604 HSIC to USB 2.0 Driver.
+
config USB_LINK_LAYER_TEST
tristate "USB Link Layer Test driver"
help
obj-$(CONFIG_USB_SEVSEG) += usbsevseg.o
obj-$(CONFIG_USB_YUREX) += yurex.o
obj-$(CONFIG_USB_HSIC_USB3503) += usb3503.o
+obj-$(CONFIG_USB_HSIC_USB4604) += usb4604.o
obj-$(CONFIG_USB_CHAOSKEY) += chaoskey.o
obj-$(CONFIG_UCSI) += ucsi.o
/* allocate memory for our device state and initialize it */
dev = kzalloc(sizeof(struct adu_device), GFP_KERNEL);
- if (dev == NULL) {
- dev_err(&interface->dev, "Out of memory\n");
+ if (!dev) {
retval = -ENOMEM;
goto exit;
}
dev->read_buffer_primary = kmalloc((4 * in_end_size), GFP_KERNEL);
if (!dev->read_buffer_primary) {
- dev_err(&interface->dev, "Couldn't allocate read_buffer_primary\n");
retval = -ENOMEM;
goto error;
}
dev->read_buffer_secondary = kmalloc((4 * in_end_size), GFP_KERNEL);
if (!dev->read_buffer_secondary) {
- dev_err(&interface->dev, "Couldn't allocate read_buffer_secondary\n");
retval = -ENOMEM;
goto error;
}
memset(dev->read_buffer_secondary + (3 * in_end_size), 'h', in_end_size);
dev->interrupt_in_buffer = kmalloc(in_end_size, GFP_KERNEL);
- if (!dev->interrupt_in_buffer) {
- dev_err(&interface->dev, "Couldn't allocate interrupt_in_buffer\n");
+ if (!dev->interrupt_in_buffer)
goto error;
- }
/* debug code prime the buffer */
memset(dev->interrupt_in_buffer, 'i', in_end_size);
dev->interrupt_in_urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!dev->interrupt_in_urb) {
- dev_err(&interface->dev, "Couldn't allocate interrupt_in_urb\n");
+ if (!dev->interrupt_in_urb)
goto error;
- }
dev->interrupt_out_buffer = kmalloc(out_end_size, GFP_KERNEL);
- if (!dev->interrupt_out_buffer) {
- dev_err(&interface->dev, "Couldn't allocate interrupt_out_buffer\n");
+ if (!dev->interrupt_out_buffer)
goto error;
- }
dev->interrupt_out_urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!dev->interrupt_out_urb) {
- dev_err(&interface->dev, "Couldn't allocate interrupt_out_urb\n");
+ if (!dev->interrupt_out_urb)
goto error;
- }
if (!usb_string(udev, udev->descriptor.iSerialNumber, dev->serial_number,
sizeof(dev->serial_number))) {
};
static atomic_t count_displays = ATOMIC_INIT(0);
-static struct workqueue_struct *wq;
static void appledisplay_complete(struct urb *urb)
{
case ACD_BTN_BRIGHT_UP:
case ACD_BTN_BRIGHT_DOWN:
pdata->button_pressed = 1;
- queue_delayed_work(wq, &pdata->work, 0);
+ schedule_delayed_work(&pdata->work, 0);
break;
case ACD_BTN_NONE:
default:
pdata = kzalloc(sizeof(struct appledisplay), GFP_KERNEL);
if (!pdata) {
retval = -ENOMEM;
- dev_err(&iface->dev, "Out of memory\n");
goto error;
}
pdata->msgdata = kmalloc(ACD_MSG_BUFFER_LEN, GFP_KERNEL);
if (!pdata->msgdata) {
retval = -ENOMEM;
- dev_err(&iface->dev,
- "Allocating buffer for control messages failed\n");
goto error;
}
pdata->urb = usb_alloc_urb(0, GFP_KERNEL);
if (!pdata->urb) {
retval = -ENOMEM;
- dev_err(&iface->dev, "Allocating URB failed\n");
goto error;
}
if (pdata) {
usb_kill_urb(pdata->urb);
- cancel_delayed_work(&pdata->work);
+ cancel_delayed_work_sync(&pdata->work);
backlight_device_unregister(pdata->bd);
usb_free_coherent(pdata->udev, ACD_URB_BUFFER_LEN,
pdata->urbdata, pdata->urb->transfer_dma);
static int __init appledisplay_init(void)
{
- wq = create_singlethread_workqueue("appledisplay");
- if (!wq) {
- printk(KERN_ERR "appledisplay: Could not create work queue\n");
- return -ENOMEM;
- }
-
return usb_register(&appledisplay_driver);
}
static void __exit appledisplay_exit(void)
{
- flush_workqueue(wq);
- destroy_workqueue(wq);
usb_deregister(&appledisplay_driver);
}
/* allocate some memory for the i/o buffer*/
iobuf = kzalloc(CYPRESS_MAX_REQSIZE, GFP_KERNEL);
if (!iobuf) {
- dev_err(&dev->udev->dev, "Out of memory!\n");
retval = -ENOMEM;
goto error;
}
/* allocate memory for our device state and initialize it */
dev = kzalloc(sizeof(*dev), GFP_KERNEL);
- if (dev == NULL) {
- dev_err(&interface->dev, "Out of memory!\n");
+ if (!dev)
goto error_mem;
- }
dev->udev = usb_get_dev(interface_to_usbdev(interface));
int retval;
buffer = kmalloc(8, GFP_KERNEL);
- if (!buffer) {
- dev_err(&cytherm->udev->dev, "out of memory\n");
+ if (!buffer)
return 0;
- }
cytherm->brightness = simple_strtoul(buf, NULL, 10);
int temp, sign;
buffer = kmalloc(8, GFP_KERNEL);
- if (!buffer) {
- dev_err(&cytherm->udev->dev, "out of memory\n");
+ if (!buffer)
return 0;
- }
/* read temperature */
retval = vendor_command(cytherm->udev, READ_RAM, TEMP, 0, buffer, 8);
unsigned char *buffer;
buffer = kmalloc(8, GFP_KERNEL);
- if (!buffer) {
- dev_err(&cytherm->udev->dev, "out of memory\n");
+ if (!buffer)
return 0;
- }
/* check button */
retval = vendor_command(cytherm->udev, READ_RAM, BUTTON, 0, buffer, 8);
unsigned char *buffer;
buffer = kmalloc(8, GFP_KERNEL);
- if (!buffer) {
- dev_err(&cytherm->udev->dev, "out of memory\n");
+ if (!buffer)
return 0;
- }
retval = vendor_command(cytherm->udev, READ_PORT, 0, 0, buffer, 8);
if (retval)
int tmp;
buffer = kmalloc(8, GFP_KERNEL);
- if (!buffer) {
- dev_err(&cytherm->udev->dev, "out of memory\n");
+ if (!buffer)
return 0;
- }
tmp = simple_strtoul(buf, NULL, 10);
unsigned char *buffer;
buffer = kmalloc(8, GFP_KERNEL);
- if (!buffer) {
- dev_err(&cytherm->udev->dev, "out of memory\n");
+ if (!buffer)
return 0;
- }
retval = vendor_command(cytherm->udev, READ_PORT, 1, 0, buffer, 8);
if (retval)
int tmp;
buffer = kmalloc(8, GFP_KERNEL);
- if (!buffer) {
- dev_err(&cytherm->udev->dev, "out of memory\n");
+ if (!buffer)
return 0;
- }
tmp = simple_strtoul(buf, NULL, 10);
int retval = -ENOMEM;
dev = kzalloc (sizeof(struct usb_cytherm), GFP_KERNEL);
- if (dev == NULL) {
- dev_err (&interface->dev, "Out of memory\n");
+ if (!dev)
goto error_mem;
- }
dev->udev = usb_get_dev(udev);
MODULE_PARM_DESC(distrust_firmware,
"true to distrust firmware power/overcurrent setup");
extern struct platform_driver u132_platform_driver;
-static struct workqueue_struct *status_queue;
-static struct workqueue_struct *command_queue;
-static struct workqueue_struct *respond_queue;
/*
* ftdi_module_lock exists to protect access to global variables
*
static void ftdi_status_requeue_work(struct usb_ftdi *ftdi, unsigned int delta)
{
- if (!queue_delayed_work(status_queue, &ftdi->status_work, delta))
+ if (!schedule_delayed_work(&ftdi->status_work, delta))
kref_put(&ftdi->kref, ftdi_elan_delete);
}
static void ftdi_status_queue_work(struct usb_ftdi *ftdi, unsigned int delta)
{
- if (queue_delayed_work(status_queue, &ftdi->status_work, delta))
+ if (schedule_delayed_work(&ftdi->status_work, delta))
kref_get(&ftdi->kref);
}
static void ftdi_status_cancel_work(struct usb_ftdi *ftdi)
{
- if (cancel_delayed_work(&ftdi->status_work))
+ if (cancel_delayed_work_sync(&ftdi->status_work))
kref_put(&ftdi->kref, ftdi_elan_delete);
}
static void ftdi_command_requeue_work(struct usb_ftdi *ftdi, unsigned int delta)
{
- if (!queue_delayed_work(command_queue, &ftdi->command_work, delta))
+ if (!schedule_delayed_work(&ftdi->command_work, delta))
kref_put(&ftdi->kref, ftdi_elan_delete);
}
static void ftdi_command_queue_work(struct usb_ftdi *ftdi, unsigned int delta)
{
- if (queue_delayed_work(command_queue, &ftdi->command_work, delta))
+ if (schedule_delayed_work(&ftdi->command_work, delta))
kref_get(&ftdi->kref);
}
static void ftdi_command_cancel_work(struct usb_ftdi *ftdi)
{
- if (cancel_delayed_work(&ftdi->command_work))
+ if (cancel_delayed_work_sync(&ftdi->command_work))
kref_put(&ftdi->kref, ftdi_elan_delete);
}
static void ftdi_response_requeue_work(struct usb_ftdi *ftdi,
unsigned int delta)
{
- if (!queue_delayed_work(respond_queue, &ftdi->respond_work, delta))
+ if (!schedule_delayed_work(&ftdi->respond_work, delta))
kref_put(&ftdi->kref, ftdi_elan_delete);
}
static void ftdi_respond_queue_work(struct usb_ftdi *ftdi, unsigned int delta)
{
- if (queue_delayed_work(respond_queue, &ftdi->respond_work, delta))
+ if (schedule_delayed_work(&ftdi->respond_work, delta))
kref_get(&ftdi->kref);
}
static void ftdi_response_cancel_work(struct usb_ftdi *ftdi)
{
- if (cancel_delayed_work(&ftdi->respond_work))
+ if (cancel_delayed_work_sync(&ftdi->respond_work))
kref_put(&ftdi->kref, ftdi_elan_delete);
}
return 0;
total_size = ftdi_elan_total_command_size(ftdi, command_size);
urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!urb) {
- dev_err(&ftdi->udev->dev, "could not get a urb to write %d commands totaling %d bytes to the Uxxx\n",
- command_size, total_size);
+ if (!urb)
return -ENOMEM;
- }
buf = usb_alloc_coherent(ftdi->udev, total_size, GFP_KERNEL,
&urb->transfer_dma);
if (!buf) {
int I = 257;
int i = 0;
urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!urb) {
- dev_err(&ftdi->udev->dev, "could not alloc a urb for flush sequence\n");
+ if (!urb)
return -ENOMEM;
- }
buf = usb_alloc_coherent(ftdi->udev, I, GFP_KERNEL, &urb->transfer_dma);
if (!buf) {
dev_err(&ftdi->udev->dev, "could not get a buffer for flush sequence\n");
int I = 4;
int i = 0;
urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!urb) {
- dev_err(&ftdi->udev->dev, "could not get a urb for the reset sequence\n");
+ if (!urb)
return -ENOMEM;
- }
buf = usb_alloc_coherent(ftdi->udev, I, GFP_KERNEL, &urb->transfer_dma);
if (!buf) {
dev_err(&ftdi->udev->dev, "could not get a buffer for the reset sequence\n");
ftdi->bulk_in_endpointAddr = endpoint->bEndpointAddress;
ftdi->bulk_in_buffer = kmalloc(buffer_size, GFP_KERNEL);
if (!ftdi->bulk_in_buffer) {
- dev_err(&ftdi->udev->dev, "Could not allocate bulk_in_buffer\n");
retval = -ENOMEM;
goto error;
}
ftdi->initialized = 0;
ftdi->registered = 0;
}
- flush_workqueue(status_queue);
- flush_workqueue(command_queue);
- flush_workqueue(respond_queue);
ftdi->disconnected += 1;
usb_set_intfdata(interface, NULL);
dev_info(&ftdi->udev->dev, "USB FTDI U132 host controller interface now disconnected\n");
pr_info("driver %s\n", ftdi_elan_driver.name);
mutex_init(&ftdi_module_lock);
INIT_LIST_HEAD(&ftdi_static_list);
- status_queue = create_singlethread_workqueue("ftdi-status-control");
- if (!status_queue)
- goto err_status_queue;
- command_queue = create_singlethread_workqueue("ftdi-command-engine");
- if (!command_queue)
- goto err_command_queue;
- respond_queue = create_singlethread_workqueue("ftdi-respond-engine");
- if (!respond_queue)
- goto err_respond_queue;
result = usb_register(&ftdi_elan_driver);
if (result) {
- destroy_workqueue(status_queue);
- destroy_workqueue(command_queue);
- destroy_workqueue(respond_queue);
pr_err("usb_register failed. Error number %d\n", result);
}
return result;
-err_respond_queue:
- destroy_workqueue(command_queue);
-err_command_queue:
- destroy_workqueue(status_queue);
-err_status_queue:
- pr_err("%s couldn't create workqueue\n", ftdi_elan_driver.name);
- return -ENOMEM;
}
static void __exit ftdi_elan_exit(void)
ftdi_status_cancel_work(ftdi);
ftdi_command_cancel_work(ftdi);
ftdi_response_cancel_work(ftdi);
- } flush_workqueue(status_queue);
- destroy_workqueue(status_queue);
- status_queue = NULL;
- flush_workqueue(command_queue);
- destroy_workqueue(command_queue);
- command_queue = NULL;
- flush_workqueue(respond_queue);
- destroy_workqueue(respond_queue);
- respond_queue = NULL;
+ }
}
kmalloc(IMGSIZE + dev->bulk_in_size, GFP_KERNEL);
if (!dev->bulk_in_buffer) {
- dev_err(&interface->dev, "Unable to allocate input buffer.\n");
idmouse_delete(dev);
return -ENOMEM;
}
dev = file->private_data;
/* verify that the device wasn't unplugged */
- if (dev == NULL || !dev->present)
+ if (!dev || !dev->present)
return -ENODEV;
dev_dbg(&dev->interface->dev, "minor %d, count = %zd\n",
int_out_urb = usb_alloc_urb(0, GFP_KERNEL);
if (!int_out_urb) {
retval = -ENOMEM;
- dev_dbg(&dev->interface->dev,
- "Unable to allocate urb\n");
goto error_no_urb;
}
buf = usb_alloc_coherent(dev->udev, dev->report_size,
int io_res; /* checks for bytes read/written and copy_to/from_user results */
dev = file->private_data;
- if (dev == NULL) {
+ if (!dev)
return -ENODEV;
- }
buffer = kzalloc(dev->report_size, GFP_KERNEL);
if (!buffer)
int retval = 0;
dev = file->private_data;
- if (dev == NULL) {
+ if (!dev)
return -ENODEV;
- }
dev_dbg(&dev->interface->dev, "minor %d\n", dev->minor);
/* allocate memory for our device state and initialize it */
dev = kzalloc(sizeof(struct iowarrior), GFP_KERNEL);
- if (dev == NULL) {
- dev_err(&interface->dev, "Out of memory\n");
+ if (!dev)
return retval;
- }
mutex_init(&dev->mutex);
/* create the urb and buffer for reading */
dev->int_in_urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!dev->int_in_urb) {
- dev_err(&interface->dev, "Couldn't allocate interrupt_in_urb\n");
+ if (!dev->int_in_urb)
goto error;
- }
dev->int_in_buffer = kmalloc(dev->report_size, GFP_KERNEL);
- if (!dev->int_in_buffer) {
- dev_err(&interface->dev, "Couldn't allocate int_in_buffer\n");
+ if (!dev->int_in_buffer)
goto error;
- }
usb_fill_int_urb(dev->int_in_urb, dev->udev,
usb_rcvintpipe(dev->udev,
dev->int_in_endpoint->bEndpointAddress),
dev->read_queue =
kmalloc(((dev->report_size + 1) * MAX_INTERRUPT_BUFFER),
GFP_KERNEL);
- if (!dev->read_queue) {
- dev_err(&interface->dev, "Couldn't allocate read_queue\n");
+ if (!dev->read_queue)
goto error;
- }
/* Get the serial-number of the chip */
memset(dev->chip_serial, 0x00, sizeof(dev->chip_serial));
usb_string(udev, udev->descriptor.iSerialNumber, dev->chip_serial,
/* allocate memory for our device state and initialize it */
dev = kzalloc(sizeof(*dev), GFP_KERNEL);
- if (dev == NULL) {
- dev_err(&intf->dev, "Out of memory\n");
+ if (!dev)
goto exit;
- }
mutex_init(&dev->mutex);
spin_lock_init(&dev->rbsl);
dev->intf = intf;
(le16_to_cpu(udev->descriptor.idProduct) == USB_DEVICE_ID_LD_COM3LAB)) &&
(le16_to_cpu(udev->descriptor.bcdDevice) <= 0x103)) {
buffer = kmalloc(256, GFP_KERNEL);
- if (buffer == NULL) {
- dev_err(&intf->dev, "Couldn't allocate string buffer\n");
+ if (!buffer)
goto error;
- }
/* usb_string makes SETUP+STALL to leave always ControlReadLoop */
usb_string(udev, 255, buffer, 256);
kfree(buffer);
dev->interrupt_in_endpoint_size = usb_endpoint_maxp(dev->interrupt_in_endpoint);
dev->ring_buffer = kmalloc(ring_buffer_size*(sizeof(size_t)+dev->interrupt_in_endpoint_size), GFP_KERNEL);
- if (!dev->ring_buffer) {
- dev_err(&intf->dev, "Couldn't allocate ring_buffer\n");
+ if (!dev->ring_buffer)
goto error;
- }
dev->interrupt_in_buffer = kmalloc(dev->interrupt_in_endpoint_size, GFP_KERNEL);
- if (!dev->interrupt_in_buffer) {
- dev_err(&intf->dev, "Couldn't allocate interrupt_in_buffer\n");
+ if (!dev->interrupt_in_buffer)
goto error;
- }
dev->interrupt_in_urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!dev->interrupt_in_urb) {
- dev_err(&intf->dev, "Couldn't allocate interrupt_in_urb\n");
+ if (!dev->interrupt_in_urb)
goto error;
- }
dev->interrupt_out_endpoint_size = dev->interrupt_out_endpoint ? usb_endpoint_maxp(dev->interrupt_out_endpoint) :
udev->descriptor.bMaxPacketSize0;
dev->interrupt_out_buffer = kmalloc(write_buffer_size*dev->interrupt_out_endpoint_size, GFP_KERNEL);
- if (!dev->interrupt_out_buffer) {
- dev_err(&intf->dev, "Couldn't allocate interrupt_out_buffer\n");
+ if (!dev->interrupt_out_buffer)
goto error;
- }
dev->interrupt_out_urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!dev->interrupt_out_urb) {
- dev_err(&intf->dev, "Couldn't allocate interrupt_out_urb\n");
+ if (!dev->interrupt_out_urb)
goto error;
- }
dev->interrupt_in_interval = min_interrupt_in_interval > dev->interrupt_in_endpoint->bInterval ? min_interrupt_in_interval : dev->interrupt_in_endpoint->bInterval;
if (dev->interrupt_out_endpoint)
dev->interrupt_out_interval = min_interrupt_out_interval > dev->interrupt_out_endpoint->bInterval ? min_interrupt_out_interval : dev->interrupt_out_endpoint->bInterval;
dev = kmalloc (sizeof(struct lego_usb_tower), GFP_KERNEL);
- if (dev == NULL) {
- dev_err(idev, "Out of memory\n");
+ if (!dev)
goto exit;
- }
mutex_init(&dev->lock);
}
dev->read_buffer = kmalloc (read_buffer_size, GFP_KERNEL);
- if (!dev->read_buffer) {
- dev_err(idev, "Couldn't allocate read_buffer\n");
+ if (!dev->read_buffer)
goto error;
- }
dev->interrupt_in_buffer = kmalloc (usb_endpoint_maxp(dev->interrupt_in_endpoint), GFP_KERNEL);
- if (!dev->interrupt_in_buffer) {
- dev_err(idev, "Couldn't allocate interrupt_in_buffer\n");
+ if (!dev->interrupt_in_buffer)
goto error;
- }
dev->interrupt_in_urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!dev->interrupt_in_urb) {
- dev_err(idev, "Couldn't allocate interrupt_in_urb\n");
+ if (!dev->interrupt_in_urb)
goto error;
- }
dev->interrupt_out_buffer = kmalloc (write_buffer_size, GFP_KERNEL);
- if (!dev->interrupt_out_buffer) {
- dev_err(idev, "Couldn't allocate interrupt_out_buffer\n");
+ if (!dev->interrupt_out_buffer)
goto error;
- }
dev->interrupt_out_urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!dev->interrupt_out_urb) {
- dev_err(idev, "Couldn't allocate interrupt_out_urb\n");
+ if (!dev->interrupt_out_urb)
goto error;
- }
dev->interrupt_in_interval = interrupt_in_interval ? interrupt_in_interval : dev->interrupt_in_endpoint->bInterval;
dev->interrupt_out_interval = interrupt_out_interval ? interrupt_out_interval : dev->interrupt_out_endpoint->bInterval;
struct usb_hub_descriptor descriptor;
/* urb for polling interrupt pipe */
struct urb *urb;
- /* LVS RH work queue */
- struct workqueue_struct *rh_queue;
/* LVH RH work */
struct work_struct rh_work;
/* RH port status */
int ret;
descriptor = kmalloc(sizeof(*descriptor), GFP_KERNEL);
- if (!descriptor) {
- dev_err(dev, "failed to allocate descriptor memory\n");
+ if (!descriptor)
return -ENOMEM;
- }
udev = create_lvs_device(intf);
if (!udev) {
{
struct lvs_rh *lvs = urb->context;
- queue_work(lvs->rh_queue, &lvs->rh_work);
+ schedule_work(&lvs->rh_work);
}
static int lvs_rh_probe(struct usb_interface *intf,
/* submit urb to poll interrupt endpoint */
lvs->urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!lvs->urb) {
- dev_err(&intf->dev, "couldn't allocate lvs urb\n");
+ if (!lvs->urb)
return -ENOMEM;
- }
-
- lvs->rh_queue = create_singlethread_workqueue("lvs_rh_queue");
- if (!lvs->rh_queue) {
- dev_err(&intf->dev, "couldn't create workqueue\n");
- ret = -ENOMEM;
- goto free_urb;
- }
INIT_WORK(&lvs->rh_work, lvs_rh_work);
ret = sysfs_create_group(&intf->dev.kobj, &lvs_attr_group);
if (ret < 0) {
dev_err(&intf->dev, "Failed to create sysfs node %d\n", ret);
- goto destroy_queue;
+ goto free_urb;
}
pipe = usb_rcvintpipe(hdev, endpoint->bEndpointAddress);
sysfs_remove:
sysfs_remove_group(&intf->dev.kobj, &lvs_attr_group);
-destroy_queue:
- destroy_workqueue(lvs->rh_queue);
free_urb:
usb_free_urb(lvs->urb);
return ret;
struct lvs_rh *lvs = usb_get_intfdata(intf);
sysfs_remove_group(&intf->dev.kobj, &lvs_attr_group);
- destroy_workqueue(lvs->rh_queue);
+ flush_work(&lvs->rh_work);
usb_free_urb(lvs->urb);
}
/* Allocate URBs */
sisusb->sisurbin = usb_alloc_urb(0, GFP_KERNEL);
if (!sisusb->sisurbin) {
- dev_err(&sisusb->sisusb_dev->dev, "Failed to allocate URBs\n");
retval = -ENOMEM;
goto error_3;
}
for (i = 0; i < sisusb->numobufs; i++) {
sisusb->sisurbout[i] = usb_alloc_urb(0, GFP_KERNEL);
if (!sisusb->sisurbout[i]) {
- dev_err(&sisusb->sisusb_dev->dev,
- "Failed to allocate URBs\n");
retval = -ENOMEM;
goto error_4;
}
int retval;
dev = kzalloc(sizeof(struct trancevibrator), GFP_KERNEL);
- if (dev == NULL) {
- dev_err(&interface->dev, "Out of memory\n");
+ if (!dev) {
retval = -ENOMEM;
goto error;
}
--- /dev/null
+/*
+ * Driver for SMSC USB4604 USB HSIC 4-port 2.0 hub controller driver
+ * Based on usb3503 driver
+ *
+ * Copyright (c) 2012-2013 Dongjin Kim (tobetter@gmail.com)
+ * Copyright (c) 2016 Linaro Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/i2c.h>
+#include <linux/delay.h>
+#include <linux/slab.h>
+#include <linux/module.h>
+#include <linux/gpio/consumer.h>
+
+enum usb4604_mode {
+ USB4604_MODE_UNKNOWN,
+ USB4604_MODE_HUB,
+ USB4604_MODE_STANDBY,
+};
+
+struct usb4604 {
+ enum usb4604_mode mode;
+ struct device *dev;
+ struct gpio_desc *gpio_reset;
+};
+
+static void usb4604_reset(struct usb4604 *hub, int state)
+{
+ gpiod_set_value_cansleep(hub->gpio_reset, state);
+
+ /* Wait for i2c logic to come up */
+ if (state)
+ msleep(250);
+}
+
+static int usb4604_connect(struct usb4604 *hub)
+{
+ struct device *dev = hub->dev;
+ struct i2c_client *client = to_i2c_client(dev);
+ int err;
+ u8 connect_cmd[] = { 0xaa, 0x55, 0x00 };
+
+ usb4604_reset(hub, 1);
+
+ err = i2c_master_send(client, connect_cmd, ARRAY_SIZE(connect_cmd));
+ if (err < 0) {
+ usb4604_reset(hub, 0);
+ return err;
+ }
+
+ hub->mode = USB4604_MODE_HUB;
+ dev_dbg(dev, "switched to HUB mode\n");
+
+ return 0;
+}
+
+static int usb4604_switch_mode(struct usb4604 *hub, enum usb4604_mode mode)
+{
+ struct device *dev = hub->dev;
+ int err = 0;
+
+ switch (mode) {
+ case USB4604_MODE_HUB:
+ err = usb4604_connect(hub);
+ break;
+
+ case USB4604_MODE_STANDBY:
+ usb4604_reset(hub, 0);
+ dev_dbg(dev, "switched to STANDBY mode\n");
+ break;
+
+ default:
+ dev_err(dev, "unknown mode is requested\n");
+ err = -EINVAL;
+ break;
+ }
+
+ return err;
+}
+
+static int usb4604_probe(struct usb4604 *hub)
+{
+ struct device *dev = hub->dev;
+ struct device_node *np = dev->of_node;
+ struct gpio_desc *gpio;
+ u32 mode = USB4604_MODE_HUB;
+
+ gpio = devm_gpiod_get_optional(dev, "reset", GPIOD_OUT_LOW);
+ if (IS_ERR(gpio))
+ return PTR_ERR(gpio);
+ hub->gpio_reset = gpio;
+
+ if (of_property_read_u32(np, "initial-mode", &hub->mode))
+ hub->mode = mode;
+
+ return usb4604_switch_mode(hub, hub->mode);
+}
+
+static int usb4604_i2c_probe(struct i2c_client *i2c,
+ const struct i2c_device_id *id)
+{
+ struct usb4604 *hub;
+
+ hub = devm_kzalloc(&i2c->dev, sizeof(*hub), GFP_KERNEL);
+ if (!hub)
+ return -ENOMEM;
+
+ i2c_set_clientdata(i2c, hub);
+ hub->dev = &i2c->dev;
+
+ return usb4604_probe(hub);
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int usb4604_i2c_suspend(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct usb4604 *hub = i2c_get_clientdata(client);
+
+ usb4604_switch_mode(hub, USB4604_MODE_STANDBY);
+
+ return 0;
+}
+
+static int usb4604_i2c_resume(struct device *dev)
+{
+ struct i2c_client *client = to_i2c_client(dev);
+ struct usb4604 *hub = i2c_get_clientdata(client);
+
+ usb4604_switch_mode(hub, hub->mode);
+
+ return 0;
+}
+#endif
+
+static SIMPLE_DEV_PM_OPS(usb4604_i2c_pm_ops, usb4604_i2c_suspend,
+ usb4604_i2c_resume);
+
+static const struct i2c_device_id usb4604_id[] = {
+ { "usb4604", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, usb4604_id);
+
+#ifdef CONFIG_OF
+static const struct of_device_id usb4604_of_match[] = {
+ { .compatible = "smsc,usb4604" },
+ {}
+};
+MODULE_DEVICE_TABLE(of, usb4604_of_match);
+#endif
+
+static struct i2c_driver usb4604_i2c_driver = {
+ .driver = {
+ .name = "usb4604",
+ .pm = &usb4604_i2c_pm_ops,
+ .of_match_table = of_match_ptr(usb4604_of_match),
+ },
+ .probe = usb4604_i2c_probe,
+ .id_table = usb4604_id,
+};
+module_i2c_driver(usb4604_i2c_driver);
+
+MODULE_DESCRIPTION("USB4604 USB HUB driver");
+MODULE_LICENSE("GPL v2");
/* allocate memory for our device state and initialize it */
dev = kzalloc(sizeof(*dev), GFP_KERNEL);
- if (dev == NULL) {
- dev_err(&interface->dev, "Out of memory\n");
+ if (!dev)
goto error;
- }
kref_init(&dev->kref);
sema_init(&dev->limit_sem, USB_LCD_CONCURRENT_WRITES);
init_usb_anchor(&dev->submitted);
dev->bulk_in_size = buffer_size;
dev->bulk_in_endpointAddr = endpoint->bEndpointAddress;
dev->bulk_in_buffer = kmalloc(buffer_size, GFP_KERNEL);
- if (!dev->bulk_in_buffer) {
- dev_err(&interface->dev,
- "Could not allocate bulk_in_buffer\n");
+ if (!dev->bulk_in_buffer)
goto error;
- }
}
if (!dev->bulk_out_endpointAddr &&
return;
buffer = kzalloc(MAXLEN, mf);
- if (!buffer) {
- dev_err(&mydev->udev->dev, "out of memory\n");
+ if (!buffer)
return;
- }
/* The device is right to left, where as you write left to right */
for (i = 0; i < mydev->textlength; i++)
int rc = -ENOMEM;
mydev = kzalloc(sizeof(struct usb_sevsegdev), GFP_KERNEL);
- if (mydev == NULL) {
- dev_err(&interface->dev, "Out of memory\n");
+ if (!mydev)
goto error_mem;
- }
mydev->udev = usb_get_dev(udev);
mydev->intf = interface;
if (!usbdev)
return NULL;
rq = kzalloc(sizeof(struct uss720_async_request), mem_flags);
- if (!rq) {
- dev_err(&usbdev->dev, "submit_async_request out of memory\n");
+ if (!rq)
return NULL;
- }
kref_init(&rq->ref_count);
INIT_LIST_HEAD(&rq->asynclist);
init_completion(&rq->compl);
rq->urb = usb_alloc_urb(0, mem_flags);
if (!rq->urb) {
kref_put(&rq->ref_count, destroy_async);
- dev_err(&usbdev->dev, "submit_async_request out of memory\n");
return NULL;
}
rq->dr = kmalloc(sizeof(*rq->dr), mem_flags);
/* allocate memory for our device state and initialize it */
dev = kzalloc(sizeof(*dev), GFP_KERNEL);
- if (!dev) {
- dev_err(&interface->dev, "Out of memory\n");
+ if (!dev)
goto error;
- }
kref_init(&dev->kref);
mutex_init(&dev->io_mutex);
spin_lock_init(&dev->lock);
/* allocate control URB */
dev->cntl_urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!dev->cntl_urb) {
- dev_err(&interface->dev, "Could not allocate control URB\n");
+ if (!dev->cntl_urb)
goto error;
- }
/* allocate buffer for control req */
dev->cntl_req = kmalloc(YUREX_BUF_SIZE, GFP_KERNEL);
- if (!dev->cntl_req) {
- dev_err(&interface->dev, "Could not allocate cntl_req\n");
+ if (!dev->cntl_req)
goto error;
- }
/* allocate buffer for control msg */
dev->cntl_buffer = usb_alloc_coherent(dev->udev, YUREX_BUF_SIZE,
/* allocate interrupt URB */
dev->urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!dev->urb) {
- dev_err(&interface->dev, "Could not allocate URB\n");
+ if (!dev->urb)
goto error;
- }
/* allocate buffer for interrupt in */
dev->int_buffer = usb_alloc_coherent(dev->udev, YUREX_BUF_SIZE,
int ret = -ENOMEM;
glue = kzalloc(sizeof(*glue), GFP_KERNEL);
- if (!glue) {
- dev_err(&pdev->dev, "failed to allocate glue context\n");
+ if (!glue)
goto err0;
- }
phy_clk = clk_get(&pdev->dev, "fck");
if (IS_ERR(phy_clk)) {
int ret = -ENOMEM;
glue = kzalloc(sizeof(*glue), GFP_KERNEL);
- if (!glue) {
- dev_err(&pdev->dev, "failed to allocate glue context\n");
+ if (!glue)
goto err0;
- }
clk = clk_get(&pdev->dev, "usb20");
if (IS_ERR(clk)) {
buf = kmalloc(sizeof(*buf), GFP_ATOMIC);
if (!buf) {
usb_ep_free_request(&dcp->ep, req);
- dev_err(dev, "recip data allocation fail\n");
return;
}
int ret;
gpriv = kzalloc(sizeof(struct usbhsg_gpriv), GFP_KERNEL);
- if (!gpriv) {
- dev_err(dev, "Could not allocate gadget priv\n");
+ if (!gpriv)
return -ENOMEM;
- }
uep = kzalloc(sizeof(struct usbhsg_uep) * pipe_size, GFP_KERNEL);
if (!uep) {
- dev_err(dev, "Could not allocate ep\n");
ret = -ENOMEM;
goto usbhs_mod_gadget_probe_err_gpriv;
}
gfp_t mem_flags)
{
struct usbhsh_request *ureq;
- struct usbhs_priv *priv = usbhsh_hpriv_to_priv(hpriv);
- struct device *dev = usbhs_priv_to_dev(priv);
ureq = kzalloc(sizeof(struct usbhsh_request), mem_flags);
- if (!ureq) {
- dev_err(dev, "ureq alloc fail\n");
+ if (!ureq)
return NULL;
- }
usbhs_pkt_init(&ureq->pkt);
ureq->urb = urb;
unsigned long flags;
uep = kzalloc(sizeof(struct usbhsh_ep), mem_flags);
- if (!uep) {
- dev_err(dev, "usbhsh_ep alloc fail\n");
+ if (!uep)
return -ENOMEM;
- }
/******************** spin lock ********************/
usbhs_lock(priv, flags);
}
info->pipe = kzalloc(sizeof(struct usbhs_pipe) * pipe_size, GFP_KERNEL);
- if (!info->pipe) {
- dev_err(dev, "Could not allocate pipe\n");
+ if (!info->pipe)
return -ENOMEM;
- }
info->size = pipe_size;
len = min(sectors, blocksize) * (pagesize + 64);
buffer = kmalloc(len, GFP_NOIO);
- if (buffer == NULL) {
- printk(KERN_WARNING "alauda_read_data: Out of memory\n");
+ if (!buffer)
return USB_STOR_TRANSPORT_ERROR;
- }
/* Figure out the initial LBA and page */
lba = address >> blockshift;
len = min(sectors, blocksize) * pagesize;
buffer = kmalloc(len, GFP_NOIO);
- if (buffer == NULL) {
- printk(KERN_WARNING "alauda_write_data: Out of memory\n");
+ if (!buffer)
return USB_STOR_TRANSPORT_ERROR;
- }
/*
* We also need a temporary block buffer, where we read in the old data,
* overwrite parts with the new data, and manipulate the redundancy data
*/
blockbuffer = kmalloc((pagesize + 64) * blocksize, GFP_NOIO);
- if (blockbuffer == NULL) {
- printk(KERN_WARNING "alauda_write_data: Out of memory\n");
+ if (!blockbuffer) {
kfree(buffer);
return USB_STOR_TRANSPORT_ERROR;
}
len = min(sectors, (unsigned int) info->blocksize) * info->pagesize;
buffer = kmalloc(len, GFP_NOIO);
- if (buffer == NULL) {
- printk(KERN_WARNING "sddr09_read_data: Out of memory\n");
+ if (!buffer)
return -ENOMEM;
- }
// This could be made much more efficient by checking for
// contiguous LBA's. Another exercise left to the student.
pagelen = (1 << info->pageshift) + (1 << CONTROL_SHIFT);
blocklen = (pagelen << info->blockshift);
blockbuffer = kmalloc(blocklen, GFP_NOIO);
- if (!blockbuffer) {
- printk(KERN_WARNING "sddr09_write_data: Out of memory\n");
+ if (!blockbuffer)
return -ENOMEM;
- }
/*
* Since we don't write the user data directly to the device,
len = min(sectors, (unsigned int) info->blocksize) * info->pagesize;
buffer = kmalloc(len, GFP_NOIO);
- if (buffer == NULL) {
- printk(KERN_WARNING "sddr09_write_data: Out of memory\n");
+ if (!buffer) {
kfree(blockbuffer);
return -ENOMEM;
}
alloc_blocks = min(numblocks, SDDR09_READ_MAP_BUFSZ >> CONTROL_SHIFT);
alloc_len = (alloc_blocks << CONTROL_SHIFT);
buffer = kmalloc(alloc_len, GFP_NOIO);
- if (buffer == NULL) {
- printk(KERN_WARNING "sddr09_read_map: out of memory\n");
+ if (!buffer) {
result = -1;
goto done;
}
struct task_struct *th;
us->current_urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!us->current_urb) {
- usb_stor_dbg(us, "URB allocation failed\n");
+ if (!us->current_urb)
return -ENOMEM;
- }
/*
* Just before we start our control thread, initialize
result = usb_stor_acquire_resources(us);
if (result)
goto BadDevice;
+ usb_autopm_get_interface_no_resume(us->pusb_intf);
snprintf(us->scsi_name, sizeof(us->scsi_name), "usb-storage %s",
dev_name(&us->pusb_intf->dev));
result = scsi_add_host(us_to_host(us), dev);
if (result) {
dev_warn(dev,
"Unable to add the scsi host\n");
- goto BadDevice;
+ goto HostAddErr;
}
/* Submit the delayed_work for SCSI-device scanning */
- usb_autopm_get_interface_no_resume(us->pusb_intf);
set_bit(US_FLIDX_SCAN_PENDING, &us->dflags);
if (delay_use > 0)
return 0;
/* We come here if there are any problems */
+HostAddErr:
+ usb_autopm_put_interface_no_suspend(us->pusb_intf);
BadDevice:
usb_stor_dbg(us, "storage_probe() failed\n");
release_everything(us);
/* allocate memory for our device state and initialize it */
dev = kzalloc(sizeof(*dev), GFP_KERNEL);
- if (!dev) {
- dev_err(&interface->dev, "Out of memory\n");
+ if (!dev)
goto error;
- }
kref_init(&dev->kref);
sema_init(&dev->limit_sem, WRITES_IN_FLIGHT);
mutex_init(&dev->io_mutex);
dev->bulk_in_size = buffer_size;
dev->bulk_in_endpointAddr = endpoint->bEndpointAddress;
dev->bulk_in_buffer = kmalloc(buffer_size, GFP_KERNEL);
- if (!dev->bulk_in_buffer) {
- dev_err(&interface->dev,
- "Could not allocate bulk_in_buffer\n");
+ if (!dev->bulk_in_buffer)
goto error;
- }
dev->bulk_in_urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!dev->bulk_in_urb) {
- dev_err(&interface->dev,
- "Could not allocate bulk_in_urb\n");
+ if (!dev->bulk_in_urb)
goto error;
- }
}
if (!dev->bulk_out_endpointAddr &&
To compile this driver as a module, choose M here: the
module will be called vhci-hcd.
+config USBIP_VHCI_HC_PORTS
+ int "Number of ports per USB/IP virtual host controller"
+ range 1 31
+ default 8
+ depends on USBIP_VHCI_HCD
+ ---help---
+ To increase number of ports available for USB/IP virtual
+ host controller driver, this defines number of ports per
+ USB/IP virtual host controller.
+
+config USBIP_VHCI_NR_HCS
+ int "Number of USB/IP virtual host controllers"
+ range 1 128
+ default 1
+ depends on USBIP_VHCI_HCD
+ ---help---
+ To increase number of ports available for USB/IP virtual
+ host controller driver, this defines number of USB/IP
+ virtual host controllers as if adding physical host
+ controllers.
+
config USBIP_HOST
tristate "Host driver"
depends on USBIP_CORE && USB
priv->urb = usb_alloc_urb(0, GFP_KERNEL);
if (!priv->urb) {
- dev_err(&udev->dev, "malloc urb\n");
usbip_event_add(ud, SDEV_EVENT_ERROR_MALLOC);
return;
}
/*
* Copyright (C) 2003-2008 Takahiro Hirofuchi
+ * Copyright (C) 2015 Nobuo Iwata
*
* This is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
};
/* Number of supported ports. Value has an upperbound of USB_MAXCHILDREN */
-#define VHCI_NPORTS 8
+#ifdef CONFIG_USBIP_VHCI_HC_PORTS
+#define VHCI_HC_PORTS CONFIG_USBIP_VHCI_HC_PORTS
+#else
+#define VHCI_HC_PORTS 8
+#endif
+
+#ifdef CONFIG_USBIP_VHCI_NR_HCS
+#define VHCI_NR_HCS CONFIG_USBIP_VHCI_NR_HCS
+#else
+#define VHCI_NR_HCS 1
+#endif
+
+#define MAX_STATUS_NAME 16
/* for usb_bus.hcpriv */
struct vhci_hcd {
spinlock_t lock;
- u32 port_status[VHCI_NPORTS];
+ u32 port_status[VHCI_HC_PORTS];
unsigned resuming:1;
unsigned long re_timeout;
* wIndex shows the port number and begins from 1.
* But, the index of this array begins from 0.
*/
- struct vhci_device vdev[VHCI_NPORTS];
+ struct vhci_device vdev[VHCI_HC_PORTS];
};
-extern struct vhci_hcd *the_controller;
-extern const struct attribute_group dev_attr_group;
+extern int vhci_num_controllers;
+extern struct platform_device **vhci_pdevs;
+extern struct attribute_group vhci_attr_group;
/* vhci_hcd.c */
-void rh_port_connect(int rhport, enum usb_device_speed speed);
+void rh_port_connect(struct vhci_device *vdev, enum usb_device_speed speed);
+
+/* vhci_sysfs.c */
+int vhci_init_attr_group(void);
+void vhci_finish_attr_group(void);
/* vhci_rx.c */
struct urb *pickup_urb_and_free_priv(struct vhci_device *vdev, __u32 seqnum);
/* vhci_tx.c */
int vhci_tx_loop(void *data);
-static inline struct vhci_device *port_to_vdev(__u32 port)
+static inline __u32 port_to_rhport(__u32 port)
+{
+ return port % VHCI_HC_PORTS;
+}
+
+static inline int port_to_pdev_nr(__u32 port)
{
- return &the_controller->vdev[port];
+ return port / VHCI_HC_PORTS;
}
static inline struct vhci_hcd *hcd_to_vhci(struct usb_hcd *hcd)
return (struct vhci_hcd *) (hcd->hcd_priv);
}
+static inline struct device *hcd_dev(struct usb_hcd *hcd)
+{
+ return (hcd)->self.controller;
+}
+
+static inline const char *hcd_name(struct usb_hcd *hcd)
+{
+ return (hcd)->self.bus_name;
+}
+
static inline struct usb_hcd *vhci_to_hcd(struct vhci_hcd *vhci)
{
return container_of((void *) vhci, struct usb_hcd, hcd_priv);
}
-static inline struct device *vhci_dev(struct vhci_hcd *vhci)
+static inline struct vhci_hcd *vdev_to_vhci(struct vhci_device *vdev)
{
- return vhci_to_hcd(vhci)->self.controller;
+ return container_of(
+ (void *)(vdev - vdev->rhport), struct vhci_hcd, vdev);
}
#endif /* __USBIP_VHCI_H */
/*
* Copyright (C) 2003-2008 Takahiro Hirofuchi
+ * Copyright (C) 2015-2016 Nobuo Iwata
*
* This is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
static const char driver_name[] = "vhci_hcd";
static const char driver_desc[] = "USB/IP Virtual Host Controller";
-struct vhci_hcd *the_controller;
+int vhci_num_controllers = VHCI_NR_HCS;
+
+struct platform_device **vhci_pdevs;
static const char * const bit_desc[] = {
"CONNECTION", /*0*/
pr_debug("\n");
}
-void rh_port_connect(int rhport, enum usb_device_speed speed)
+void rh_port_connect(struct vhci_device *vdev, enum usb_device_speed speed)
{
+ struct vhci_hcd *vhci = vdev_to_vhci(vdev);
+ int rhport = vdev->rhport;
+ u32 status;
unsigned long flags;
usbip_dbg_vhci_rh("rh_port_connect %d\n", rhport);
- spin_lock_irqsave(&the_controller->lock, flags);
+ spin_lock_irqsave(&vhci->lock, flags);
+
+ status = vhci->port_status[rhport];
- the_controller->port_status[rhport] |= USB_PORT_STAT_CONNECTION
- | (1 << USB_PORT_FEAT_C_CONNECTION);
+ status |= USB_PORT_STAT_CONNECTION | (1 << USB_PORT_FEAT_C_CONNECTION);
switch (speed) {
case USB_SPEED_HIGH:
- the_controller->port_status[rhport] |= USB_PORT_STAT_HIGH_SPEED;
+ status |= USB_PORT_STAT_HIGH_SPEED;
break;
case USB_SPEED_LOW:
- the_controller->port_status[rhport] |= USB_PORT_STAT_LOW_SPEED;
+ status |= USB_PORT_STAT_LOW_SPEED;
break;
default:
break;
}
- spin_unlock_irqrestore(&the_controller->lock, flags);
+ vhci->port_status[rhport] = status;
+
+ spin_unlock_irqrestore(&vhci->lock, flags);
- usb_hcd_poll_rh_status(vhci_to_hcd(the_controller));
+ usb_hcd_poll_rh_status(vhci_to_hcd(vhci));
}
-static void rh_port_disconnect(int rhport)
+static void rh_port_disconnect(struct vhci_device *vdev)
{
+ struct vhci_hcd *vhci = vdev_to_vhci(vdev);
+ int rhport = vdev->rhport;
+ u32 status;
unsigned long flags;
usbip_dbg_vhci_rh("rh_port_disconnect %d\n", rhport);
- spin_lock_irqsave(&the_controller->lock, flags);
+ spin_lock_irqsave(&vhci->lock, flags);
+
+ status = vhci->port_status[rhport];
+
+ status &= ~USB_PORT_STAT_CONNECTION;
+ status |= (1 << USB_PORT_FEAT_C_CONNECTION);
- the_controller->port_status[rhport] &= ~USB_PORT_STAT_CONNECTION;
- the_controller->port_status[rhport] |=
- (1 << USB_PORT_FEAT_C_CONNECTION);
+ vhci->port_status[rhport] = status;
- spin_unlock_irqrestore(&the_controller->lock, flags);
- usb_hcd_poll_rh_status(vhci_to_hcd(the_controller));
+ spin_unlock_irqrestore(&vhci->lock, flags);
+ usb_hcd_poll_rh_status(vhci_to_hcd(vhci));
}
#define PORT_C_MASK \
int changed = 0;
unsigned long flags;
- retval = DIV_ROUND_UP(VHCI_NPORTS + 1, 8);
+ retval = DIV_ROUND_UP(VHCI_HC_PORTS + 1, 8);
memset(buf, 0, retval);
vhci = hcd_to_vhci(hcd);
}
/* check pseudo status register for each port */
- for (rhport = 0; rhport < VHCI_NPORTS; rhport++) {
+ for (rhport = 0; rhport < VHCI_HC_PORTS; rhport++) {
if ((vhci->port_status[rhport] & PORT_C_MASK)) {
/* The status of a port has been changed, */
usbip_dbg_vhci_rh("port %d status changed\n", rhport);
desc->bDescLength = 9;
desc->wHubCharacteristics = cpu_to_le16(
HUB_CHAR_INDV_PORT_LPSM | HUB_CHAR_COMMON_OCPM);
- desc->bNbrPorts = VHCI_NPORTS;
+ desc->bNbrPorts = VHCI_HC_PORTS;
desc->u.hs.DeviceRemovable[0] = 0xff;
desc->u.hs.DeviceRemovable[1] = 0xff;
}
int rhport;
unsigned long flags;
- u32 prev_port_status[VHCI_NPORTS];
+ u32 prev_port_status[VHCI_HC_PORTS];
if (!HCD_HW_ACCESSIBLE(hcd))
return -ETIMEDOUT;
*/
usbip_dbg_vhci_rh("typeReq %x wValue %x wIndex %x\n", typeReq, wValue,
wIndex);
- if (wIndex > VHCI_NPORTS)
+ if (wIndex > VHCI_HC_PORTS)
pr_err("invalid port number %d\n", wIndex);
rhport = ((__u8)(wIndex & 0x00ff)) - 1;
break;
case GetPortStatus:
usbip_dbg_vhci_rh(" GetPortStatus port %x\n", wIndex);
- if (wIndex > VHCI_NPORTS || wIndex < 1) {
+ if (wIndex > VHCI_HC_PORTS || wIndex < 1) {
pr_err("invalid port number %d\n", wIndex);
retval = -EPIPE;
}
static struct vhci_device *get_vdev(struct usb_device *udev)
{
- int i;
+ struct platform_device *pdev;
+ struct usb_hcd *hcd;
+ struct vhci_hcd *vhci;
+ int pdev_nr, rhport;
if (!udev)
return NULL;
- for (i = 0; i < VHCI_NPORTS; i++)
- if (the_controller->vdev[i].udev == udev)
- return port_to_vdev(i);
+ for (pdev_nr = 0; pdev_nr < vhci_num_controllers; pdev_nr++) {
+ pdev = *(vhci_pdevs + pdev_nr);
+ if (pdev == NULL)
+ continue;
+ hcd = platform_get_drvdata(pdev);
+ if (hcd == NULL)
+ continue;
+ vhci = hcd_to_vhci(hcd);
+ for (rhport = 0; rhport < VHCI_HC_PORTS; rhport++) {
+ if (vhci->vdev[rhport].udev == udev)
+ return &vhci->vdev[rhport];
+ }
+ }
return NULL;
}
{
struct vhci_device *vdev = get_vdev(urb->dev);
struct vhci_priv *priv;
+ struct vhci_hcd *vhci = vdev_to_vhci(vdev);
unsigned long flags;
if (!vdev) {
spin_lock_irqsave(&vdev->priv_lock, flags);
- priv->seqnum = atomic_inc_return(&the_controller->seqnum);
+ priv->seqnum = atomic_inc_return(&vhci->seqnum);
if (priv->seqnum == 0xffff)
dev_info(&urb->dev->dev, "seqnum max\n");
static int vhci_urb_enqueue(struct usb_hcd *hcd, struct urb *urb,
gfp_t mem_flags)
{
+ struct vhci_hcd *vhci = hcd_to_vhci(hcd);
struct device *dev = &urb->dev->dev;
+ u8 portnum = urb->dev->portnum;
int ret = 0;
struct vhci_device *vdev;
unsigned long flags;
usbip_dbg_vhci_hc("enter, usb_hcd %p urb %p mem_flags %d\n",
hcd, urb, mem_flags);
+ if (portnum > VHCI_HC_PORTS) {
+ pr_err("invalid port number %d\n", portnum);
+ return -ENODEV;
+ }
+ vdev = &vhci->vdev[portnum-1];
+
/* patch to usb_sg_init() is in 2.5.60 */
BUG_ON(!urb->transfer_buffer && urb->transfer_buffer_length);
- spin_lock_irqsave(&the_controller->lock, flags);
+ spin_lock_irqsave(&vhci->lock, flags);
if (urb->status != -EINPROGRESS) {
dev_err(dev, "URB already unlinked!, status %d\n", urb->status);
- spin_unlock_irqrestore(&the_controller->lock, flags);
+ spin_unlock_irqrestore(&vhci->lock, flags);
return urb->status;
}
- vdev = port_to_vdev(urb->dev->portnum-1);
-
/* refuse enqueue for dead connection */
spin_lock(&vdev->ud.lock);
if (vdev->ud.status == VDEV_ST_NULL ||
vdev->ud.status == VDEV_ST_ERROR) {
dev_err(dev, "enqueue for inactive port %d\n", vdev->rhport);
spin_unlock(&vdev->ud.lock);
- spin_unlock_irqrestore(&the_controller->lock, flags);
+ spin_unlock_irqrestore(&vhci->lock, flags);
return -ENODEV;
}
spin_unlock(&vdev->ud.lock);
out:
vhci_tx_urb(urb);
- spin_unlock_irqrestore(&the_controller->lock, flags);
+ spin_unlock_irqrestore(&vhci->lock, flags);
return 0;
no_need_xmit:
usb_hcd_unlink_urb_from_ep(hcd, urb);
no_need_unlink:
- spin_unlock_irqrestore(&the_controller->lock, flags);
+ spin_unlock_irqrestore(&vhci->lock, flags);
if (!ret)
- usb_hcd_giveback_urb(vhci_to_hcd(the_controller),
- urb, urb->status);
+ usb_hcd_giveback_urb(hcd, urb, urb->status);
return ret;
}
*/
static int vhci_urb_dequeue(struct usb_hcd *hcd, struct urb *urb, int status)
{
+ struct vhci_hcd *vhci = hcd_to_vhci(hcd);
struct vhci_priv *priv;
struct vhci_device *vdev;
unsigned long flags;
pr_info("dequeue a urb %p\n", urb);
- spin_lock_irqsave(&the_controller->lock, flags);
+ spin_lock_irqsave(&vhci->lock, flags);
priv = urb->hcpriv;
if (!priv) {
/* URB was never linked! or will be soon given back by
* vhci_rx. */
- spin_unlock_irqrestore(&the_controller->lock, flags);
+ spin_unlock_irqrestore(&vhci->lock, flags);
return -EIDRM;
}
ret = usb_hcd_check_unlink_urb(hcd, urb, status);
if (ret) {
- spin_unlock_irqrestore(&the_controller->lock, flags);
+ spin_unlock_irqrestore(&vhci->lock, flags);
return ret;
}
}
usb_hcd_unlink_urb_from_ep(hcd, urb);
- spin_unlock_irqrestore(&the_controller->lock, flags);
- usb_hcd_giveback_urb(vhci_to_hcd(the_controller), urb,
- urb->status);
- spin_lock_irqsave(&the_controller->lock, flags);
+ spin_unlock_irqrestore(&vhci->lock, flags);
+ usb_hcd_giveback_urb(vhci_to_hcd(vhci), urb, urb->status);
+ spin_lock_irqsave(&vhci->lock, flags);
} else {
/* tcp connection is alive */
unlink = kzalloc(sizeof(struct vhci_unlink), GFP_ATOMIC);
if (!unlink) {
spin_unlock(&vdev->priv_lock);
- spin_unlock_irqrestore(&the_controller->lock, flags);
+ spin_unlock_irqrestore(&vhci->lock, flags);
usbip_event_add(&vdev->ud, VDEV_EVENT_ERROR_MALLOC);
return -ENOMEM;
}
- unlink->seqnum = atomic_inc_return(&the_controller->seqnum);
+ unlink->seqnum = atomic_inc_return(&vhci->seqnum);
if (unlink->seqnum == 0xffff)
pr_info("seqnum max\n");
spin_unlock(&vdev->priv_lock);
}
- spin_unlock_irqrestore(&the_controller->lock, flags);
+ spin_unlock_irqrestore(&vhci->lock, flags);
usbip_dbg_vhci_hc("leave\n");
return 0;
static void vhci_device_unlink_cleanup(struct vhci_device *vdev)
{
+ struct vhci_hcd *vhci = vdev_to_vhci(vdev);
+ struct usb_hcd *hcd = vhci_to_hcd(vhci);
struct vhci_unlink *unlink, *tmp;
unsigned long flags;
- spin_lock_irqsave(&the_controller->lock, flags);
+ spin_lock_irqsave(&vhci->lock, flags);
spin_lock(&vdev->priv_lock);
list_for_each_entry_safe(unlink, tmp, &vdev->unlink_tx, list) {
urb->status = -ENODEV;
- usb_hcd_unlink_urb_from_ep(vhci_to_hcd(the_controller), urb);
+ usb_hcd_unlink_urb_from_ep(hcd, urb);
list_del(&unlink->list);
spin_unlock(&vdev->priv_lock);
- spin_unlock_irqrestore(&the_controller->lock, flags);
+ spin_unlock_irqrestore(&vhci->lock, flags);
- usb_hcd_giveback_urb(vhci_to_hcd(the_controller), urb,
- urb->status);
+ usb_hcd_giveback_urb(hcd, urb, urb->status);
- spin_lock_irqsave(&the_controller->lock, flags);
+ spin_lock_irqsave(&vhci->lock, flags);
spin_lock(&vdev->priv_lock);
kfree(unlink);
}
spin_unlock(&vdev->priv_lock);
- spin_unlock_irqrestore(&the_controller->lock, flags);
+ spin_unlock_irqrestore(&vhci->lock, flags);
}
/*
* is actually given back by vhci_rx after receiving its return pdu.
*
*/
- rh_port_disconnect(vdev->rhport);
+ rh_port_disconnect(vdev);
pr_info("disconnect device\n");
}
static void vhci_device_init(struct vhci_device *vdev)
{
- memset(vdev, 0, sizeof(*vdev));
+ memset(vdev, 0, sizeof(struct vhci_device));
vdev->ud.side = USBIP_VHCI;
vdev->ud.status = VDEV_ST_NULL;
usbip_start_eh(&vdev->ud);
}
+static int hcd_name_to_id(const char *name)
+{
+ char *c;
+ long val;
+ int ret;
+
+ c = strchr(name, '.');
+ if (c == NULL)
+ return 0;
+
+ ret = kstrtol(c+1, 10, &val);
+ if (ret < 0)
+ return ret;
+
+ return val;
+}
+
static int vhci_start(struct usb_hcd *hcd)
{
struct vhci_hcd *vhci = hcd_to_vhci(hcd);
- int rhport;
+ int id, rhport;
int err = 0;
usbip_dbg_vhci_hc("enter vhci_start\n");
/* initialize private data of usb_hcd */
- for (rhport = 0; rhport < VHCI_NPORTS; rhport++) {
+ for (rhport = 0; rhport < VHCI_HC_PORTS; rhport++) {
struct vhci_device *vdev = &vhci->vdev[rhport];
vhci_device_init(vdev);
hcd->power_budget = 0; /* no limit */
hcd->uses_new_polling = 1;
+ id = hcd_name_to_id(hcd_name(hcd));
+ if (id < 0) {
+ pr_err("invalid vhci name %s\n", hcd_name(hcd));
+ return -EINVAL;
+ }
+
/* vhci_hcd is now ready to be controlled through sysfs */
- err = sysfs_create_group(&vhci_dev(vhci)->kobj, &dev_attr_group);
- if (err) {
- pr_err("create sysfs files\n");
- return err;
+ if (id == 0) {
+ err = vhci_init_attr_group();
+ if (err) {
+ pr_err("init attr group\n");
+ return err;
+ }
+ err = sysfs_create_group(&hcd_dev(hcd)->kobj, &vhci_attr_group);
+ if (err) {
+ pr_err("create sysfs files\n");
+ vhci_finish_attr_group();
+ return err;
+ }
+ pr_info("created sysfs %s\n", hcd_name(hcd));
}
return 0;
static void vhci_stop(struct usb_hcd *hcd)
{
struct vhci_hcd *vhci = hcd_to_vhci(hcd);
- int rhport = 0;
+ int id, rhport;
usbip_dbg_vhci_hc("stop VHCI controller\n");
/* 1. remove the userland interface of vhci_hcd */
- sysfs_remove_group(&vhci_dev(vhci)->kobj, &dev_attr_group);
+ id = hcd_name_to_id(hcd_name(hcd));
+ if (id == 0) {
+ sysfs_remove_group(&hcd_dev(hcd)->kobj, &vhci_attr_group);
+ vhci_finish_attr_group();
+ }
/* 2. shutdown all the ports of vhci_hcd */
- for (rhport = 0; rhport < VHCI_NPORTS; rhport++) {
+ for (rhport = 0; rhport < VHCI_HC_PORTS; rhport++) {
struct vhci_device *vdev = &vhci->vdev[rhport];
usbip_event_add(&vdev->ud, VDEV_EVENT_REMOVED);
}
hcd->has_tt = 1;
- /* this is private data for vhci_hcd */
- the_controller = hcd_to_vhci(hcd);
-
/*
* Finish generic HCD structure initialization and register.
* Call the driver's reset() and start() routines.
if (ret != 0) {
pr_err("usb_add_hcd failed %d\n", ret);
usb_put_hcd(hcd);
- the_controller = NULL;
return ret;
}
*/
usb_remove_hcd(hcd);
usb_put_hcd(hcd);
- the_controller = NULL;
return 0;
}
static int vhci_hcd_suspend(struct platform_device *pdev, pm_message_t state)
{
struct usb_hcd *hcd;
- int rhport = 0;
+ struct vhci_hcd *vhci;
+ int rhport;
int connected = 0;
int ret = 0;
unsigned long flags;
hcd = platform_get_drvdata(pdev);
+ if (!hcd)
+ return 0;
+ vhci = hcd_to_vhci(hcd);
- spin_lock_irqsave(&the_controller->lock, flags);
+ spin_lock_irqsave(&vhci->lock, flags);
- for (rhport = 0; rhport < VHCI_NPORTS; rhport++)
- if (the_controller->port_status[rhport] &
- USB_PORT_STAT_CONNECTION)
+ for (rhport = 0; rhport < VHCI_HC_PORTS; rhport++)
+ if (vhci->port_status[rhport] & USB_PORT_STAT_CONNECTION)
connected += 1;
- spin_unlock_irqrestore(&the_controller->lock, flags);
+ spin_unlock_irqrestore(&vhci->lock, flags);
if (connected > 0) {
dev_info(&pdev->dev,
dev_dbg(&pdev->dev, "%s\n", __func__);
hcd = platform_get_drvdata(pdev);
+ if (!hcd)
+ return 0;
set_bit(HCD_FLAG_HW_ACCESSIBLE, &hcd->flags);
usb_hcd_poll_rh_status(hcd);
},
};
-/*
- * The VHCI 'device' is 'virtual'; not a real plug&play hardware.
- * We need to add this virtual device as a platform device arbitrarily:
- * 1. platform_device_register()
- */
-static void the_pdev_release(struct device *dev)
+static int add_platform_device(int id)
{
+ struct platform_device *pdev;
+ int dev_nr;
+
+ if (id == 0)
+ dev_nr = -1;
+ else
+ dev_nr = id;
+
+ pdev = platform_device_register_simple(driver_name, dev_nr, NULL, 0);
+ if (IS_ERR(pdev))
+ return PTR_ERR(pdev);
+
+ *(vhci_pdevs + id) = pdev;
+ return 0;
}
-static struct platform_device the_pdev = {
- /* should be the same name as driver_name */
- .name = driver_name,
- .id = -1,
- .dev = {
- .release = the_pdev_release,
- },
-};
+static void del_platform_devices(void)
+{
+ struct platform_device *pdev;
+ int i;
+
+ for (i = 0; i < vhci_num_controllers; i++) {
+ pdev = *(vhci_pdevs + i);
+ if (pdev != NULL)
+ platform_device_unregister(pdev);
+ *(vhci_pdevs + i) = NULL;
+ }
+ sysfs_remove_link(&platform_bus.kobj, driver_name);
+}
static int __init vhci_hcd_init(void)
{
- int ret;
+ int i, ret;
if (usb_disabled())
return -ENODEV;
+ if (vhci_num_controllers < 1)
+ vhci_num_controllers = 1;
+
+ vhci_pdevs = kcalloc(vhci_num_controllers, sizeof(void *), GFP_KERNEL);
+ if (vhci_pdevs == NULL)
+ return -ENOMEM;
+
ret = platform_driver_register(&vhci_driver);
if (ret)
goto err_driver_register;
- ret = platform_device_register(&the_pdev);
- if (ret)
- goto err_platform_device_register;
+ for (i = 0; i < vhci_num_controllers; i++) {
+ ret = add_platform_device(i);
+ if (ret)
+ goto err_platform_device_register;
+ }
pr_info(DRIVER_DESC " v" USBIP_VERSION "\n");
return ret;
err_platform_device_register:
+ del_platform_devices();
platform_driver_unregister(&vhci_driver);
err_driver_register:
+ kfree(vhci_pdevs);
return ret;
}
static void __exit vhci_hcd_exit(void)
{
- platform_device_unregister(&the_pdev);
+ del_platform_devices();
platform_driver_unregister(&vhci_driver);
+ kfree(vhci_pdevs);
}
module_init(vhci_hcd_init);
static void vhci_recv_ret_submit(struct vhci_device *vdev,
struct usbip_header *pdu)
{
+ struct vhci_hcd *vhci = vdev_to_vhci(vdev);
struct usbip_device *ud = &vdev->ud;
struct urb *urb;
unsigned long flags;
if (!urb) {
pr_err("cannot find a urb of seqnum %u\n", pdu->base.seqnum);
pr_info("max seqnum %d\n",
- atomic_read(&the_controller->seqnum));
+ atomic_read(&vhci->seqnum));
usbip_event_add(ud, VDEV_EVENT_ERROR_TCP);
return;
}
usbip_dbg_vhci_rx("now giveback urb %p\n", urb);
- spin_lock_irqsave(&the_controller->lock, flags);
- usb_hcd_unlink_urb_from_ep(vhci_to_hcd(the_controller), urb);
- spin_unlock_irqrestore(&the_controller->lock, flags);
+ spin_lock_irqsave(&vhci->lock, flags);
+ usb_hcd_unlink_urb_from_ep(vhci_to_hcd(vhci), urb);
+ spin_unlock_irqrestore(&vhci->lock, flags);
- usb_hcd_giveback_urb(vhci_to_hcd(the_controller), urb, urb->status);
+ usb_hcd_giveback_urb(vhci_to_hcd(vhci), urb, urb->status);
usbip_dbg_vhci_rx("Leave\n");
}
static void vhci_recv_ret_unlink(struct vhci_device *vdev,
struct usbip_header *pdu)
{
+ struct vhci_hcd *vhci = vdev_to_vhci(vdev);
struct vhci_unlink *unlink;
struct urb *urb;
unsigned long flags;
urb->status = pdu->u.ret_unlink.status;
pr_info("urb->status %d\n", urb->status);
- spin_lock_irqsave(&the_controller->lock, flags);
- usb_hcd_unlink_urb_from_ep(vhci_to_hcd(the_controller), urb);
- spin_unlock_irqrestore(&the_controller->lock, flags);
+ spin_lock_irqsave(&vhci->lock, flags);
+ usb_hcd_unlink_urb_from_ep(vhci_to_hcd(vhci), urb);
+ spin_unlock_irqrestore(&vhci->lock, flags);
- usb_hcd_giveback_urb(vhci_to_hcd(the_controller), urb,
- urb->status);
+ usb_hcd_giveback_urb(vhci_to_hcd(vhci), urb, urb->status);
}
kfree(unlink);
/*
* Copyright (C) 2003-2008 Takahiro Hirofuchi
+ * Copyright (C) 2015-2016 Nobuo Iwata
*
* This is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
#include <linux/kthread.h>
#include <linux/file.h>
#include <linux/net.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
#include "usbip_common.h"
#include "vhci.h"
/* TODO: refine locking ?*/
/* Sysfs entry to show port status */
-static ssize_t status_show(struct device *dev, struct device_attribute *attr,
- char *out)
+static ssize_t status_show_vhci(int pdev_nr, char *out)
{
+ struct platform_device *pdev = *(vhci_pdevs + pdev_nr);
+ struct vhci_hcd *vhci;
char *s = out;
int i = 0;
unsigned long flags;
- BUG_ON(!the_controller || !out);
+ if (!pdev || !out) {
+ usbip_dbg_vhci_sysfs("show status error\n");
+ return 0;
+ }
+
+ vhci = hcd_to_vhci(platform_get_drvdata(pdev));
- spin_lock_irqsave(&the_controller->lock, flags);
+ spin_lock_irqsave(&vhci->lock, flags);
/*
* output example:
- * prt sta spd dev socket local_busid
- * 000 004 000 000 c5a7bb80 1-2.3
- * 001 004 000 000 d8cee980 2-3.4
+ * port sta spd dev socket local_busid
+ * 0000 004 000 00000000 c5a7bb80 1-2.3
+ * 0001 004 000 00000000 d8cee980 2-3.4
*
* IP address can be retrieved from a socket pointer address by looking
* up /proc/net/{tcp,tcp6}. Also, a userland program may remember a
* port number and its peer IP address.
*/
- out += sprintf(out,
- "prt sta spd bus dev socket local_busid\n");
-
- for (i = 0; i < VHCI_NPORTS; i++) {
- struct vhci_device *vdev = port_to_vdev(i);
+ for (i = 0; i < VHCI_HC_PORTS; i++) {
+ struct vhci_device *vdev = &vhci->vdev[i];
spin_lock(&vdev->ud.lock);
- out += sprintf(out, "%03u %03u ", i, vdev->ud.status);
+ out += sprintf(out, "%04u %03u ",
+ (pdev_nr * VHCI_HC_PORTS) + i,
+ vdev->ud.status);
if (vdev->ud.status == VDEV_ST_USED) {
out += sprintf(out, "%03u %08x ",
- vdev->speed, vdev->devid);
- out += sprintf(out, "%16p ", vdev->ud.tcp_socket);
- out += sprintf(out, "%s", dev_name(&vdev->udev->dev));
+ vdev->speed, vdev->devid);
+ out += sprintf(out, "%16p %s",
+ vdev->ud.tcp_socket,
+ dev_name(&vdev->udev->dev));
} else {
- out += sprintf(out, "000 000 000 0000000000000000 0-0");
+ out += sprintf(out, "000 00000000 ");
+ out += sprintf(out, "0000000000000000 0-0");
}
out += sprintf(out, "\n");
spin_unlock(&vdev->ud.lock);
}
- spin_unlock_irqrestore(&the_controller->lock, flags);
+ spin_unlock_irqrestore(&vhci->lock, flags);
+
+ return out - s;
+}
+
+static ssize_t status_show_not_ready(int pdev_nr, char *out)
+{
+ char *s = out;
+ int i = 0;
+
+ for (i = 0; i < VHCI_HC_PORTS; i++) {
+ out += sprintf(out, "%04u %03u ",
+ (pdev_nr * VHCI_HC_PORTS) + i,
+ VDEV_ST_NOTASSIGNED);
+ out += sprintf(out, "000 00000000 0000000000000000 0-0");
+ out += sprintf(out, "\n");
+ }
+ return out - s;
+}
+
+static int status_name_to_id(const char *name)
+{
+ char *c;
+ long val;
+ int ret;
+
+ c = strchr(name, '.');
+ if (c == NULL)
+ return 0;
+ ret = kstrtol(c+1, 10, &val);
+ if (ret < 0)
+ return ret;
+
+ return val;
+}
+
+static ssize_t status_show(struct device *dev,
+ struct device_attribute *attr, char *out)
+{
+ char *s = out;
+ int pdev_nr;
+
+ out += sprintf(out,
+ "port sta spd dev socket local_busid\n");
+
+ pdev_nr = status_name_to_id(attr->attr.name);
+ if (pdev_nr < 0)
+ out += status_show_not_ready(pdev_nr, out);
+ else
+ out += status_show_vhci(pdev_nr, out);
+
+ return out - s;
+}
+
+static ssize_t nports_show(struct device *dev, struct device_attribute *attr,
+ char *out)
+{
+ char *s = out;
+
+ out += sprintf(out, "%d\n", VHCI_HC_PORTS * vhci_num_controllers);
return out - s;
}
-static DEVICE_ATTR_RO(status);
+static DEVICE_ATTR_RO(nports);
/* Sysfs entry to shutdown a virtual connection */
-static int vhci_port_disconnect(__u32 rhport)
+static int vhci_port_disconnect(struct vhci_hcd *vhci, __u32 rhport)
{
- struct vhci_device *vdev;
+ struct vhci_device *vdev = &vhci->vdev[rhport];
unsigned long flags;
usbip_dbg_vhci_sysfs("enter\n");
/* lock */
- spin_lock_irqsave(&the_controller->lock, flags);
-
- vdev = port_to_vdev(rhport);
-
+ spin_lock_irqsave(&vhci->lock, flags);
spin_lock(&vdev->ud.lock);
+
if (vdev->ud.status == VDEV_ST_NULL) {
pr_err("not connected %d\n", vdev->ud.status);
/* unlock */
spin_unlock(&vdev->ud.lock);
- spin_unlock_irqrestore(&the_controller->lock, flags);
+ spin_unlock_irqrestore(&vhci->lock, flags);
return -EINVAL;
}
/* unlock */
spin_unlock(&vdev->ud.lock);
- spin_unlock_irqrestore(&the_controller->lock, flags);
+ spin_unlock_irqrestore(&vhci->lock, flags);
usbip_event_add(&vdev->ud, VDEV_EVENT_DOWN);
return 0;
}
+static int valid_port(__u32 pdev_nr, __u32 rhport)
+{
+ if (pdev_nr >= vhci_num_controllers) {
+ pr_err("pdev %u\n", pdev_nr);
+ return 0;
+ }
+ if (rhport >= VHCI_HC_PORTS) {
+ pr_err("rhport %u\n", rhport);
+ return 0;
+ }
+ return 1;
+}
+
static ssize_t store_detach(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
- int err;
- __u32 rhport = 0;
+ __u32 port = 0, pdev_nr = 0, rhport = 0;
+ struct usb_hcd *hcd;
+ int ret;
- if (sscanf(buf, "%u", &rhport) != 1)
+ if (kstrtoint(buf, 10, &port) < 0)
return -EINVAL;
- /* check rhport */
- if (rhport >= VHCI_NPORTS) {
- dev_err(dev, "invalid port %u\n", rhport);
+ pdev_nr = port_to_pdev_nr(port);
+ rhport = port_to_rhport(port);
+
+ if (!valid_port(pdev_nr, rhport))
return -EINVAL;
+
+ hcd = platform_get_drvdata(*(vhci_pdevs + pdev_nr));
+ if (hcd == NULL) {
+ dev_err(dev, "port is not ready %u\n", port);
+ return -EAGAIN;
}
- err = vhci_port_disconnect(rhport);
- if (err < 0)
+ ret = vhci_port_disconnect(hcd_to_vhci(hcd), rhport);
+ if (ret < 0)
return -EINVAL;
usbip_dbg_vhci_sysfs("Leave\n");
}
static DEVICE_ATTR(detach, S_IWUSR, NULL, store_detach);
-/* Sysfs entry to establish a virtual connection */
-static int valid_args(__u32 rhport, enum usb_device_speed speed)
+static int valid_args(__u32 pdev_nr, __u32 rhport, enum usb_device_speed speed)
{
- /* check rhport */
- if (rhport >= VHCI_NPORTS) {
- pr_err("port %u\n", rhport);
- return -EINVAL;
+ if (!valid_port(pdev_nr, rhport)) {
+ return 0;
}
- /* check speed */
switch (speed) {
case USB_SPEED_LOW:
case USB_SPEED_FULL:
default:
pr_err("Failed attach request for unsupported USB speed: %s\n",
usb_speed_string(speed));
- return -EINVAL;
+ return 0;
}
- return 0;
+ return 1;
}
+/* Sysfs entry to establish a virtual connection */
/*
* To start a new USB/IP attachment, a userland program needs to setup a TCP
* connection and then write its socket descriptor with remote device
static ssize_t store_attach(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
- struct vhci_device *vdev;
struct socket *socket;
int sockfd = 0;
- __u32 rhport = 0, devid = 0, speed = 0;
+ __u32 port = 0, pdev_nr = 0, rhport = 0, devid = 0, speed = 0;
+ struct usb_hcd *hcd;
+ struct vhci_hcd *vhci;
+ struct vhci_device *vdev;
int err;
unsigned long flags;
* @devid: unique device identifier in a remote host
* @speed: usb device speed in a remote host
*/
- if (sscanf(buf, "%u %u %u %u", &rhport, &sockfd, &devid, &speed) != 4)
+ if (sscanf(buf, "%u %u %u %u", &port, &sockfd, &devid, &speed) != 4)
return -EINVAL;
+ pdev_nr = port_to_pdev_nr(port);
+ rhport = port_to_rhport(port);
- usbip_dbg_vhci_sysfs("rhport(%u) sockfd(%u) devid(%u) speed(%u)\n",
- rhport, sockfd, devid, speed);
+ usbip_dbg_vhci_sysfs("port(%u) pdev(%d) rhport(%u)\n",
+ port, pdev_nr, rhport);
+ usbip_dbg_vhci_sysfs("sockfd(%u) devid(%u) speed(%u)\n",
+ sockfd, devid, speed);
/* check received parameters */
- if (valid_args(rhport, speed) < 0)
+ if (!valid_args(pdev_nr, rhport, speed))
return -EINVAL;
+ hcd = platform_get_drvdata(*(vhci_pdevs + pdev_nr));
+ if (hcd == NULL) {
+ dev_err(dev, "port %d is not ready\n", port);
+ return -EAGAIN;
+ }
+ vhci = hcd_to_vhci(hcd);
+ vdev = &vhci->vdev[rhport];
+
/* Extract socket from fd. */
socket = sockfd_lookup(sockfd, &err);
if (!socket)
/* now need lock until setting vdev status as used */
/* begin a lock */
- spin_lock_irqsave(&the_controller->lock, flags);
- vdev = port_to_vdev(rhport);
+ spin_lock_irqsave(&vhci->lock, flags);
spin_lock(&vdev->ud.lock);
if (vdev->ud.status != VDEV_ST_NULL) {
/* end of the lock */
spin_unlock(&vdev->ud.lock);
- spin_unlock_irqrestore(&the_controller->lock, flags);
+ spin_unlock_irqrestore(&vhci->lock, flags);
sockfd_put(socket);
return -EINVAL;
}
- dev_info(dev,
- "rhport(%u) sockfd(%d) devid(%u) speed(%u) speed_str(%s)\n",
- rhport, sockfd, devid, speed, usb_speed_string(speed));
+ dev_info(dev, "pdev(%u) rhport(%u) sockfd(%d)\n",
+ pdev_nr, rhport, sockfd);
+ dev_info(dev, "devid(%u) speed(%u) speed_str(%s)\n",
+ devid, speed, usb_speed_string(speed));
vdev->devid = devid;
vdev->speed = speed;
vdev->ud.status = VDEV_ST_NOTASSIGNED;
spin_unlock(&vdev->ud.lock);
- spin_unlock_irqrestore(&the_controller->lock, flags);
+ spin_unlock_irqrestore(&vhci->lock, flags);
/* end the lock */
vdev->ud.tcp_rx = kthread_get_run(vhci_rx_loop, &vdev->ud, "vhci_rx");
vdev->ud.tcp_tx = kthread_get_run(vhci_tx_loop, &vdev->ud, "vhci_tx");
- rh_port_connect(rhport, speed);
+ rh_port_connect(vdev, speed);
return count;
}
static DEVICE_ATTR(attach, S_IWUSR, NULL, store_attach);
-static struct attribute *dev_attrs[] = {
- &dev_attr_status.attr,
- &dev_attr_detach.attr,
- &dev_attr_attach.attr,
- &dev_attr_usbip_debug.attr,
- NULL,
+#define MAX_STATUS_NAME 16
+
+struct status_attr {
+ struct device_attribute attr;
+ char name[MAX_STATUS_NAME+1];
};
-const struct attribute_group dev_attr_group = {
- .attrs = dev_attrs,
+static struct status_attr *status_attrs;
+
+static void set_status_attr(int id)
+{
+ struct status_attr *status;
+
+ status = status_attrs + id;
+ if (id == 0)
+ strcpy(status->name, "status");
+ else
+ snprintf(status->name, MAX_STATUS_NAME+1, "status.%d", id);
+ status->attr.attr.name = status->name;
+ status->attr.attr.mode = S_IRUGO;
+ status->attr.show = status_show;
+}
+
+static int init_status_attrs(void)
+{
+ int id;
+
+ status_attrs = kcalloc(vhci_num_controllers, sizeof(struct status_attr),
+ GFP_KERNEL);
+ if (status_attrs == NULL)
+ return -ENOMEM;
+
+ for (id = 0; id < vhci_num_controllers; id++)
+ set_status_attr(id);
+
+ return 0;
+}
+
+static void finish_status_attrs(void)
+{
+ kfree(status_attrs);
+}
+
+struct attribute_group vhci_attr_group = {
+ .attrs = NULL,
};
+
+int vhci_init_attr_group(void)
+{
+ struct attribute **attrs;
+ int ret, i;
+
+ attrs = kcalloc((vhci_num_controllers + 5), sizeof(struct attribute *),
+ GFP_KERNEL);
+ if (attrs == NULL)
+ return -ENOMEM;
+
+ ret = init_status_attrs();
+ if (ret) {
+ kfree(attrs);
+ return ret;
+ }
+ *attrs = &dev_attr_nports.attr;
+ *(attrs + 1) = &dev_attr_detach.attr;
+ *(attrs + 2) = &dev_attr_attach.attr;
+ *(attrs + 3) = &dev_attr_usbip_debug.attr;
+ for (i = 0; i < vhci_num_controllers; i++)
+ *(attrs + i + 4) = &((status_attrs + i)->attr.attr);
+ vhci_attr_group.attrs = attrs;
+ return 0;
+}
+
+void vhci_finish_attr_group(void)
+{
+ finish_status_attrs();
+ kfree(vhci_attr_group.attrs);
+}
if (ud->tcp_socket)
kernel_sock_shutdown(ud->tcp_socket, SHUT_RDWR);
- if (ud->tcp_tx) {
+ if (ud->tcp_rx) {
kthread_stop_put(ud->tcp_rx);
ud->tcp_rx = NULL;
}
urb_p->urb->status = -EINPROGRESS;
/* FIXME: more pipe setup to please usbip_common */
- urb_p->urb->pipe &= ~(11 << 30);
+ urb_p->urb->pipe &= ~(3 << 30);
switch (urb_p->ep->type) {
case USB_ENDPOINT_XFER_BULK:
urb_p->urb->pipe |= (PIPE_BULK << 30);
zero_padding = sizeof(struct aes_ccm_block) - zero_padding;
dst_size = blen + sizeof(b0) + sizeof(b1) + zero_padding;
dst_buf = kzalloc(dst_size, GFP_KERNEL);
- if (dst_buf == NULL) {
- printk(KERN_ERR "E: can't alloc destination buffer\n");
+ if (!dst_buf)
goto error_dst_buf;
- }
memset(iv, 0, sizeof(iv));
struct wusb_keydvt_out keydvt_out;
hs = kcalloc(3, sizeof(hs[0]), GFP_KERNEL);
- if (hs == NULL) {
- dev_err(dev, "can't allocate handshake data\n");
+ if (!hs)
goto error_kzalloc;
- }
/* We need to turn encryption before beginning the 4way
* hshake (WUSB1.0[.3.2.2]) */
epd = &iface->cur_altsetting->endpoint[0].desc;
wa->nep_buffer_size = 1024;
wa->nep_buffer = kmalloc(wa->nep_buffer_size, GFP_KERNEL);
- if (wa->nep_buffer == NULL) {
- dev_err(dev,
- "Unable to allocate notification's read buffer\n");
+ if (!wa->nep_buffer)
goto error_nep_buffer;
- }
wa->nep_urb = usb_alloc_urb(0, GFP_KERNEL);
- if (wa->nep_urb == NULL) {
- dev_err(dev, "Unable to allocate notification URB\n");
+ if (wa->nep_urb == NULL)
goto error_urb_alloc;
- }
usb_fill_int_urb(wa->nep_urb, usb_dev,
usb_rcvintpipe(usb_dev, epd->bEndpointAddress),
wa->nep_buffer, wa->nep_buffer_size,
goto out;
wa->dti_urb = usb_alloc_urb(0, GFP_KERNEL);
- if (wa->dti_urb == NULL) {
- dev_err(dev, "Can't allocate DTI URB\n");
+ if (wa->dti_urb == NULL)
goto error_dti_urb_alloc;
- }
usb_fill_bulk_urb(
wa->dti_urb, wa->usb_dev,
usb_rcvbulkpipe(wa->usb_dev, 0x80 | dti_epd->bEndpointAddress),
goto error_rd_buffer;
}
hwarc->neep_urb = usb_alloc_urb(0, GFP_KERNEL);
- if (hwarc->neep_urb == NULL) {
- dev_err(dev, "Unable to allocate notification URB\n");
+ if (hwarc->neep_urb == NULL)
goto error_urb_alloc;
- }
usb_fill_int_urb(hwarc->neep_urb, usb_dev,
usb_rcvintpipe(usb_dev, epd->bEndpointAddress),
hwarc->rd_buffer, PAGE_SIZE,
/* allocate the urb's */
usb_pcwd->intr_urb = usb_alloc_urb(0, GFP_KERNEL);
- if (!usb_pcwd->intr_urb) {
- pr_err("Out of memory\n");
+ if (!usb_pcwd->intr_urb)
goto error;
- }
/* initialise the intr urb's */
usb_fill_int_urb(usb_pcwd->intr_urb, udev, pipe,
#define BCMA_CLKCTLST_HAVEALPREQ 0x00000008 /* ALP available request */
#define BCMA_CLKCTLST_HAVEHTREQ 0x00000010 /* HT available request */
#define BCMA_CLKCTLST_HWCROFF 0x00000020 /* Force HW clock request off */
+#define BCMA_CLKCTLST_HQCLKREQ 0x00000040 /* HQ Clock */
#define BCMA_CLKCTLST_EXTRESREQ 0x00000700 /* Mask of external resource requests */
#define BCMA_CLKCTLST_EXTRESREQ_SHIFT 8
#define BCMA_CLKCTLST_HAVEALP 0x00010000 /* ALP available */
#define to_ulpi_driver(d) container_of(d, struct ulpi_driver, driver)
-int ulpi_register_driver(struct ulpi_driver *drv);
+/*
+ * use a macro to avoid include chaining to get THIS_MODULE
+ */
+#define ulpi_register_driver(drv) __ulpi_register_driver(drv, THIS_MODULE)
+int __ulpi_register_driver(struct ulpi_driver *drv, struct module *module);
void ulpi_unregister_driver(struct ulpi_driver *drv);
#define module_ulpi_driver(__ulpi_driver) \
#ifndef _LINUX_MFD_SYSCON_ATMEL_SFR_H
#define _LINUX_MFD_SYSCON_ATMEL_SFR_H
+#define AT91_SFR_DDRCFG 0x04 /* DDR Configuration Register */
+/* 0x08 ~ 0x0c: Reserved */
+#define AT91_SFR_OHCIICR 0x10 /* OHCI INT Configuration Register */
+#define AT91_SFR_OHCIISR 0x14 /* OHCI INT Status Register */
#define AT91_SFR_I2SCLKSEL 0x90 /* I2SC Register */
+/* Field definitions */
+#define AT91_OHCIICR_SUSPEND_A BIT(8)
+#define AT91_OHCIICR_SUSPEND_B BIT(9)
+#define AT91_OHCIICR_SUSPEND_C BIT(10)
+
+#define AT91_OHCIICR_USB_SUSPEND (AT91_OHCIICR_SUSPEND_A | \
+ AT91_OHCIICR_SUSPEND_B | \
+ AT91_OHCIICR_SUSPEND_C)
+
+
#endif /* _LINUX_MFD_SYSCON_ATMEL_SFR_H */
projects / deliverable / linux.git / commitdiff
