--- /dev/null
+/*
+ * Device Tree file for SolidRun Clearfog revision A1 rev 2.0 (88F6828)
+ *
+ * Copyright (C) 2015 Russell King
+ *
+ * This board is in development; the contents of this file work with
+ * the A1 rev 2.0 of the board, which does not represent final
+ * production board. Things will change, don't expect this file to
+ * remain compatible info the future.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "armada-388.dtsi"
+#include "armada-38x-solidrun-microsom.dtsi"
+
+/ {
+ model = "SolidRun Clearfog A1";
+ compatible = "solidrun,clearfog-a1", "marvell,armada388",
+ "marvell,armada385", "marvell,armada380";
+
+ aliases {
+ /* So that mvebu u-boot can update the MAC addresses */
+ ethernet1 = ð0;
+ ethernet2 = ð1;
+ ethernet3 = ð2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ reg_3p3v: regulator-3p3v {
+ compatible = "regulator-fixed";
+ regulator-name = "3P3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ soc {
+ internal-regs {
+ ethernet@30000 {
+ phy-mode = "sgmii";
+ status = "okay";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ ethernet@34000 {
+ phy-mode = "sgmii";
+ status = "okay";
+
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+
+ i2c@11000 {
+ /* Is there anything on this? */
+ clock-frequency = <100000>;
+ pinctrl-0 = <&i2c0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ /*
+ * PCA9655 GPIO expander, up to 1MHz clock.
+ * 0-CON3 CLKREQ#
+ * 1-CON3 PERST#
+ * 2-CON2 PERST#
+ * 3-CON3 W_DISABLE
+ * 4-CON2 CLKREQ#
+ * 5-USB3 overcurrent
+ * 6-USB3 power
+ * 7-CON2 W_DISABLE
+ * 8-JP4 P1
+ * 9-JP4 P4
+ * 10-JP4 P5
+ * 11-m.2 DEVSLP
+ * 12-SFP_LOS
+ * 13-SFP_TX_FAULT
+ * 14-SFP_TX_DISABLE
+ * 15-SFP_MOD_DEF0
+ */
+ expander0: gpio-expander@20 {
+ /*
+ * This is how it should be:
+ * compatible = "onnn,pca9655",
+ * "nxp,pca9555";
+ * but you can't do this because of
+ * the way I2C works.
+ */
+ compatible = "nxp,pca9555";
+ gpio-controller;
+ #gpio-cells = <2>;
+ reg = <0x20>;
+
+ pcie1_0_clkreq {
+ gpio-hog;
+ gpios = <0 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "pcie1.0-clkreq";
+ };
+ pcie1_0_w_disable {
+ gpio-hog;
+ gpios = <3 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "pcie1.0-w-disable";
+ };
+ pcie2_0_clkreq {
+ gpio-hog;
+ gpios = <4 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "pcie2.0-clkreq";
+ };
+ pcie2_0_w_disable {
+ gpio-hog;
+ gpios = <7 GPIO_ACTIVE_LOW>;
+ output-low;
+ line-name = "pcie2.0-w-disable";
+ };
+ usb3_ilimit {
+ gpio-hog;
+ gpios = <5 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "usb3-current-limit";
+ };
+ usb3_power {
+ gpio-hog;
+ gpios = <6 GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "usb3-power";
+ };
+ m2_devslp {
+ gpio-hog;
+ gpios = <11 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "m.2 devslp";
+ };
+ sfp_los {
+ /* SFP loss of signal */
+ gpio-hog;
+ gpios = <12 GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "sfp-los";
+ };
+ sfp_tx_fault {
+ /* SFP laser fault */
+ gpio-hog;
+ gpios = <13 GPIO_ACTIVE_HIGH>;
+ input;
+ line-name = "sfp-tx-fault";
+ };
+ sfp_tx_disable {
+ /* SFP transmit disable */
+ gpio-hog;
+ gpios = <14 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "sfp-tx-disable";
+ };
+ sfp_mod_def0 {
+ /* SFP module present */
+ gpio-hog;
+ gpios = <15 GPIO_ACTIVE_LOW>;
+ input;
+ line-name = "sfp-mod-def0";
+ };
+ };
+
+ /* The MCP3021 is 100kHz clock only */
+ mikrobus_adc: mcp3021@4c {
+ compatible = "microchip,mcp3021";
+ reg = <0x4c>;
+ };
+
+ /* Also something at 0x64 */
+ };
+
+ i2c@11100 {
+ /*
+ * Routed to SFP, mikrobus, and PCIe.
+ * SFP limits this to 100kHz, and requires
+ * an AT24C01A/02/04 with address pins tied
+ * low, which takes addresses 0x50 and 0x51.
+ * Mikrobus doesn't specify beyond an I2C
+ * bus being present.
+ * PCIe uses ARP to assign addresses, or
+ * 0x63-0x64.
+ */
+ clock-frequency = <100000>;
+ pinctrl-0 = <&clearfog_i2c1_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ mdio@72004 {
+ pinctrl-0 = <&mdio_pins>;
+ pinctrl-names = "default";
+
+ phy_dedicated: ethernet-phy@0 {
+ /*
+ * Annoyingly, the marvell phy driver
+ * configures the LED register, rather
+ * than preserving reset-loaded setting.
+ * We undo that rubbish here.
+ */
+ marvell,reg-init = <3 16 0 0x101e>;
+ reg = <0>;
+ };
+ };
+
+ pinctrl@18000 {
+ clearfog_dsa0_clk_pins: clearfog-dsa0-clk-pins {
+ marvell,pins = "mpp46";
+ marvell,function = "ref";
+ };
+ clearfog_dsa0_pins: clearfog-dsa0-pins {
+ marvell,pins = "mpp23", "mpp41";
+ marvell,function = "gpio";
+ };
+ clearfog_i2c1_pins: i2c1-pins {
+ /* SFP, PCIe, mSATA, mikrobus */
+ marvell,pins = "mpp26", "mpp27";
+ marvell,function = "i2c1";
+ };
+ clearfog_sdhci_cd_pins: clearfog-sdhci-cd-pins {
+ marvell,pins = "mpp20";
+ marvell,function = "gpio";
+ };
+ clearfog_sdhci_pins: clearfog-sdhci-pins {
+ marvell,pins = "mpp21", "mpp28",
+ "mpp37", "mpp38",
+ "mpp39", "mpp40";
+ marvell,function = "sd0";
+ };
+ clearfog_spi1_cs_pins: spi1-cs-pins {
+ marvell,pins = "mpp55";
+ marvell,function = "spi1";
+ };
+ mikro_pins: mikro-pins {
+ /* int: mpp22 rst: mpp29 */
+ marvell,pins = "mpp22", "mpp29";
+ marvell,function = "gpio";
+ };
+ mikro_spi_pins: mikro-spi-pins {
+ marvell,pins = "mpp43";
+ marvell,function = "spi1";
+ };
+ mikro_uart_pins: mikro-uart-pins {
+ marvell,pins = "mpp24", "mpp25";
+ marvell,function = "ua1";
+ };
+ rear_button_pins: rear-button-pins {
+ marvell,pins = "mpp34";
+ marvell,function = "gpio";
+ };
+ };
+
+ sata@a8000 {
+ /* pinctrl? */
+ status = "okay";
+ };
+
+ sata@e0000 {
+ /* pinctrl? */
+ status = "okay";
+ };
+
+ sdhci@d8000 {
+ bus-width = <4>;
+ cd-gpios = <&gpio0 20 GPIO_ACTIVE_LOW>;
+ no-1-8-v;
+ pinctrl-0 = <&clearfog_sdhci_pins
+ &clearfog_sdhci_cd_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ vmmc = <®_3p3v>;
+ wp-inverted;
+ };
+
+ serial@12100 {
+ /* mikrobus uart */
+ pinctrl-0 = <&mikro_uart_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+
+ spi@10680 {
+ /*
+ * We don't seem to have the W25Q32 on the
+ * A1 Rev 2.0 boards, so disable SPI.
+ * CS0: W25Q32 (doesn't appear to be present)
+ * CS1:
+ * CS2: mikrobus
+ */
+ pinctrl-0 = <&spi1_pins
+ &clearfog_spi1_cs_pins
+ &mikro_spi_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+
+ spi-flash@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "w25q32", "jedec,spi-nor";
+ reg = <0>; /* Chip select 0 */
+ spi-max-frequency = <3000000>;
+ status = "disabled";
+ };
+ };
+
+ usb@58000 {
+ /* CON3, nearest power. */
+ status = "okay";
+ };
+
+ usb3@f0000 {
+ /* CON2, nearest CPU, USB2 only. */
+ status = "okay";
+ };
+
+ usb3@f8000 {
+ /* CON7 */
+ status = "okay";
+ };
+ };
+
+ pcie-controller {
+ status = "okay";
+ /*
+ * The two PCIe units are accessible through
+ * the mini-PCIe connectors on the board.
+ */
+ pcie@2,0 {
+ /* Port 1, Lane 0. CON3, nearest power. */
+ reset-gpios = <&expander0 1 GPIO_ACTIVE_LOW>;
+ status = "okay";
+ };
+ pcie@3,0 {
+ /* Port 2, Lane 0. CON2, nearest CPU. */
+ reset-gpios = <&expander0 2 GPIO_ACTIVE_LOW>;
+ status = "okay";
+ };
+ };
+ };
+
+ dsa@0 {
+ compatible = "marvell,dsa";
+ dsa,ethernet = <ð1>;
+ dsa,mii-bus = <&mdio>;
+ pinctrl-0 = <&clearfog_dsa0_clk_pins &clearfog_dsa0_pins>;
+ pinctrl-names = "default";
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ switch@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <4 0>;
+
+ port@0 {
+ reg = <0>;
+ label = "lan1";
+ };
+
+ port@1 {
+ reg = <1>;
+ label = "lan2";
+ };
+
+ port@2 {
+ reg = <2>;
+ label = "lan3";
+ };
+
+ port@3 {
+ reg = <3>;
+ label = "lan4";
+ };
+
+ port@4 {
+ reg = <4>;
+ label = "lan5";
+ };
+
+ port@5 {
+ reg = <5>;
+ label = "cpu";
+ };
+
+ port@6 {
+ /* 88E1512 external phy */
+ reg = <6>;
+ label = "lan6";
+ fixed-link {
+ speed = <1000>;
+ full-duplex;
+ };
+ };
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ pinctrl-0 = <&rear_button_pins>;
+ pinctrl-names = "default";
+
+ button_0 {
+ /* The rear SW3 button */
+ label = "Rear Button";
+ gpios = <&gpio1 2 GPIO_ACTIVE_LOW>;
+ linux,can-disable;
+ linux,code = <BTN_0>;
+ };
+ };
+};
--- /dev/null
+/*
+ * Device Tree file for SolidRun Armada 38x Microsom
+ *
+ * Copyright (C) 2015 Russell King
+ *
+ * This board is in development; the contents of this file work with
+ * the A1 rev 2.0 of the board, which does not represent final
+ * production board. Things will change, don't expect this file to
+ * remain compatible info the future.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * version 2 as published by the Free Software Foundation.
+ *
+ * This file is distributed in the hope that it will be useful
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ memory {
+ device_type = "memory";
+ reg = <0x00000000 0x10000000>; /* 256 MB */
+ };
+
+ soc {
+ ranges = <MBUS_ID(0xf0, 0x01) 0 0xf1000000 0x100000
+ MBUS_ID(0x01, 0x1d) 0 0xfff00000 0x100000
+ MBUS_ID(0x09, 0x19) 0 0xf1100000 0x10000
+ MBUS_ID(0x09, 0x15) 0 0xf1110000 0x10000>;
+
+ internal-regs {
+ ethernet@70000 {
+ pinctrl-0 = <&ge0_rgmii_pins>;
+ pinctrl-names = "default";
+ phy = <&phy_dedicated>;
+ phy-mode = "rgmii-id";
+ status = "okay";
+ };
+
+ mdio@72004 {
+ /*
+ * Add the phy clock here, so the phy can be
+ * accessed to read its IDs prior to binding
+ * with the driver.
+ */
+ pinctrl-0 = <&mdio_pins µsom_phy_clk_pins>;
+ pinctrl-names = "default";
+
+ phy_dedicated: ethernet-phy@0 {
+ /*
+ * Annoyingly, the marvell phy driver
+ * configures the LED register, rather
+ * than preserving reset-loaded setting.
+ * We undo that rubbish here.
+ */
+ marvell,reg-init = <3 16 0 0x101e>;
+ reg = <0>;
+ };
+ };
+
+ pinctrl@18000 {
+ microsom_phy_clk_pins: microsom-phy-clk-pins {
+ marvell,pins = "mpp45";
+ marvell,function = "ref";
+ };
+ };
+
+ rtc@a3800 {
+ /*
+ * If the rtc doesn't work, run "date reset"
+ * twice in u-boot.
+ */
+ status = "okay";
+ };
+
+ serial@12000 {
+ pinctrl-0 = <&uart0_pins>;
+ pinctrl-names = "default";
+ status = "okay";
+ };
+ };
+ };
+};
projects / deliverable / linux.git / commitdiff
