of led events.
You can change triggers in a similar manner to the way an IO
scheduler is chosen. Trigger specific parameters can appear in
- /sys/class/leds/<led> once a given trigger is selected.
+ /sys/class/leds/<led> once a given trigger is selected. For
+ their documentation see sysfs-class-led-trigger-*.
What: /sys/class/leds/<led>/inverted
Date: January 2011
--- /dev/null
+What: /sys/class/leds/<led>/delay_on
+Date: Jun 2012
+KernelVersion: 3.6
+Contact: linux-leds@vger.kernel.org
+Description:
+ Specifies for how many milliseconds the LED has to stay at
+ LED_FULL brightness after it has been armed.
+ Defaults to 100 ms.
+
+What: /sys/class/leds/<led>/delay_off
+Date: Jun 2012
+KernelVersion: 3.6
+Contact: linux-leds@vger.kernel.org
+Description:
+ Specifies for how many milliseconds the LED has to stay at
+ LED_OFF brightness after it has been armed.
+ Defaults to 100 ms.
+
+What: /sys/class/leds/<led>/invert
+Date: Jun 2012
+KernelVersion: 3.6
+Contact: linux-leds@vger.kernel.org
+Description:
+ Reverse the blink logic. If set to 0 (default) blink on for
+ delay_on ms, then blink off for delay_off ms, leaving the LED
+ normally off. If set to 1, blink off for delay_off ms, then
+ blink on for delay_on ms, leaving the LED normally on.
+ Setting this value also immediately changes the LED state.
+
+What: /sys/class/leds/<led>/shot
+Date: Jun 2012
+KernelVersion: 3.6
+Contact: linux-leds@vger.kernel.org
+Description:
+ Write any non-empty string to signal an events, this starts a
+ blink sequence if not already running.
a device, i.e. no other LED class device can be assigned the same
label.
+- default-state : The initial state of the LED. Valid values are "on", "off",
+ and "keep". If the LED is already on or off and the default-state property is
+ set the to same value, then no glitch should be produced where the LED
+ momentarily turns off (or on). The "keep" setting will keep the LED at
+ whatever its current state is, without producing a glitch. The default is
+ off if this property is not present.
+
- linux,default-trigger : This parameter, if present, is a
string defining the trigger assigned to the LED. Current triggers are:
"backlight" - LED will act as a back-light, controlled by the framebuffer
- active-low : Boolean, makes LED active low.
Default : false
- default-state : see
- Documentation/devicetree/bindings/leds/leds-gpio.txt
+ Documentation/devicetree/bindings/leds/common.txt
- linux,default-trigger : see
Documentation/devicetree/bindings/leds/common.txt
- active-low : Boolean, makes LED active low.
Default : false
- default-state : see
- Documentation/devicetree/bindings/leds/leds-gpio.txt
+ Documentation/devicetree/bindings/leds/common.txt
- linux,default-trigger : see
Documentation/devicetree/bindings/leds/common.txt
see Documentation/devicetree/bindings/leds/common.txt
- linux,default-trigger : (optional)
see Documentation/devicetree/bindings/leds/common.txt
-- default-state: (optional) The initial state of the LED. Valid
- values are "on", "off", and "keep". If the LED is already on or off
- and the default-state property is set the to same value, then no
- glitch should be produced where the LED momentarily turns off (or
- on). The "keep" setting will keep the LED at whatever its current
- state is, without producing a glitch. The default is off if this
- property is not present.
+- default-state: (optional) The initial state of the LED.
+ see Documentation/devicetree/bindings/leds/common.txt
- retain-state-suspended: (optional) The suspend state can be retained.Such
as charge-led gpio.
- panic-indicator : (optional)
--- /dev/null
+LEDs connected to is31fl319x LED controller chip
+
+Required properties:
+- compatible : Should be any of
+ "issi,is31fl3190"
+ "issi,is31fl3191"
+ "issi,is31fl3193"
+ "issi,is31fl3196"
+ "issi,is31fl3199"
+ "si-en,sn3199".
+- #address-cells: Must be 1.
+- #size-cells: Must be 0.
+- reg: 0x64, 0x65, 0x66, or 0x67.
+
+Optional properties:
+- audio-gain-db : audio gain selection for external analog modulation input.
+ Valid values: 0 - 21, step by 3 (rounded down)
+ Default: 0
+
+Each led is represented as a sub-node of the issi,is31fl319x device.
+There can be less leds subnodes than the chip can support but not more.
+
+Required led sub-node properties:
+- reg : number of LED line
+ Valid values: 1 - number of leds supported by the chip variant.
+
+Optional led sub-node properties:
+- label : see Documentation/devicetree/bindings/leds/common.txt.
+- linux,default-trigger :
+ see Documentation/devicetree/bindings/leds/common.txt.
+- led-max-microamp : (optional)
+ Valid values: 5000 - 40000, step by 5000 (rounded down)
+ Default: 20000 (20 mA)
+ Note: a driver will take the lowest of all led limits since the
+ chip has a single global setting. The lowest value will be chosen
+ due to the PWM specificity, where lower brightness is achieved
+ by reducing the dury-cycle of pulses and not the current, which
+ will always have its peak value equal to led-max-microamp.
+
+Examples:
+
+fancy_leds: leds@65 {
+ compatible = "issi,is31fl3196";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0x65>;
+
+ red_aux: led@1 {
+ label = "red:aux";
+ reg = <1>;
+ led-max-microamp = <10000>;
+ };
+
+ green_power: led@5 {
+ label = "green:power";
+ reg = <5>;
+ linux,default-trigger = "default-on";
+ };
+};
--- /dev/null
+Qualcomm PM8058 LED driver
+
+The Qualcomm PM8058 is a multi-functional device which contains
+an LED driver block for up to six LEDs: three normal LEDs, two
+"flash" LEDs and one "keypad backlight" LED. The names are
+quoted because sometimes these LED drivers are used for wildly
+different things than flash or keypad backlight: their names
+are more of a suggestion than a hard-wired usecase.
+
+Hardware-wise the different LEDs support slightly different
+output currents. The "flash" LEDs do not need to charge nor
+do they support external triggers. They are just powerful LED
+drivers.
+
+The LEDs appear as children to the PM8058 device, with the
+proper compatible string. For the PM8058 bindings see:
+mfd/qcom-pm8xxx.txt.
+
+Each LED is represented as a sub-node of the syscon device. Each
+node's name represents the name of the corresponding LED.
+
+LED sub-node properties:
+
+Required properties:
+- compatible: one of
+ "qcom,pm8058-led" (for the normal LEDs at 0x131, 0x132 and 0x133)
+ "qcom,pm8058-keypad-led" (for the "keypad" LED at 0x48)
+ "qcom,pm8058-flash-led" (for the "flash" LEDs at 0x49 and 0xFB)
+
+Optional properties:
+- label: see Documentation/devicetree/bindings/leds/common.txt
+- default-state: see Documentation/devicetree/bindings/leds/common.txt
+- linux,default-trigger: see Documentation/devicetree/bindings/leds/common.txt
+
+Example:
+
+qcom,ssbi@500000 {
+ pmicintc: pmic@0 {
+ compatible = "qcom,pm8058";
+ led@48 {
+ compatible = "qcom,pm8058-keypad-led";
+ reg = <0x48>;
+ label = "pm8050:white:keypad";
+ default-state = "off";
+ };
+ led@131 {
+ compatible = "qcom,pm8058-led";
+ reg = <0x131>;
+ label = "pm8058:red";
+ default-state = "off";
+ };
+ led@132 {
+ compatible = "qcom,pm8058-led";
+ reg = <0x132>;
+ label = "pm8058:yellow";
+ default-state = "off";
+ linux,default-trigger = "mmc0";
+ };
+ led@133 {
+ compatible = "qcom,pm8058-led";
+ reg = <0x133>;
+ label = "pm8058:green";
+ default-state = "on";
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
see Documentation/devicetree/bindings/leds/common.txt
- linux,default-trigger : (optional)
see Documentation/devicetree/bindings/leds/common.txt
-- default-state: (optional) The initial state of the LED. Valid
- values are "on", "off", and "keep". If the LED is already on or off
- and the default-state property is set the to same value, then no
- glitch should be produced where the LED momentarily turns off (or
- on). The "keep" setting will keep the LED at whatever its current
- state is, without producing a glitch. The default is off if this
- property is not present.
+- default-state: (optional) The initial state of the LED
+ see Documentation/devicetree/bindings/leds/common.txt
Example:
--- /dev/null
+Kernel driver for Mellanox systems LEDs
+=======================================
+
+Provide system LED support for the nex Mellanox systems:
+"msx6710", "msx6720", "msb7700", "msn2700", "msx1410",
+"msn2410", "msb7800", "msn2740", "msn2100".
+
+Description
+-----------
+Driver provides the following LEDs for the systems "msx6710", "msx6720",
+"msb7700", "msn2700", "msx1410", "msn2410", "msb7800", "msn2740":
+ mlxcpld:fan1:green
+ mlxcpld:fan1:red
+ mlxcpld:fan2:green
+ mlxcpld:fan2:red
+ mlxcpld:fan3:green
+ mlxcpld:fan3:red
+ mlxcpld:fan4:green
+ mlxcpld:fan4:red
+ mlxcpld:psu:green
+ mlxcpld:psu:red
+ mlxcpld:status:green
+ mlxcpld:status:red
+
+ "status"
+ CPLD reg offset: 0x20
+ Bits [3:0]
+
+ "psu"
+ CPLD reg offset: 0x20
+ Bits [7:4]
+
+ "fan1"
+ CPLD reg offset: 0x21
+ Bits [3:0]
+
+ "fan2"
+ CPLD reg offset: 0x21
+ Bits [7:4]
+
+ "fan3"
+ CPLD reg offset: 0x22
+ Bits [3:0]
+
+ "fan4"
+ CPLD reg offset: 0x22
+ Bits [7:4]
+
+ Color mask for all the above LEDs:
+ [bit3,bit2,bit1,bit0] or
+ [bit7,bit6,bit5,bit4]:
+ [0,0,0,0] = LED OFF
+ [0,1,0,1] = Red static ON
+ [1,1,0,1] = Green static ON
+ [0,1,1,0] = Red blink 3Hz
+ [1,1,1,0] = Green blink 3Hz
+ [0,1,1,1] = Red blink 6Hz
+ [1,1,1,1] = Green blink 6Hz
+
+Driver provides the following LEDs for the system "msn2100":
+ mlxcpld:fan:green
+ mlxcpld:fan:red
+ mlxcpld:psu1:green
+ mlxcpld:psu1:red
+ mlxcpld:psu2:green
+ mlxcpld:psu2:red
+ mlxcpld:status:green
+ mlxcpld:status:red
+ mlxcpld:uid:blue
+
+ "status"
+ CPLD reg offset: 0x20
+ Bits [3:0]
+
+ "fan"
+ CPLD reg offset: 0x21
+ Bits [3:0]
+
+ "psu1"
+ CPLD reg offset: 0x23
+ Bits [3:0]
+
+ "psu2"
+ CPLD reg offset: 0x23
+ Bits [7:4]
+
+ "uid"
+ CPLD reg offset: 0x24
+ Bits [3:0]
+
+ Color mask for all the above LEDs, excepted uid:
+ [bit3,bit2,bit1,bit0] or
+ [bit7,bit6,bit5,bit4]:
+ [0,0,0,0] = LED OFF
+ [0,1,0,1] = Red static ON
+ [1,1,0,1] = Green static ON
+ [0,1,1,0] = Red blink 3Hz
+ [1,1,1,0] = Green blink 3Hz
+ [0,1,1,1] = Red blink 6Hz
+ [1,1,1,1] = Green blink 6Hz
+
+ Color mask for uid LED:
+ [bit3,bit2,bit1,bit0]:
+ [0,0,0,0] = LED OFF
+ [1,1,0,1] = Blue static ON
+ [1,1,1,0] = Blue blink 3Hz
+ [1,1,1,1] = Blue blink 6Hz
+
+Driver supports HW blinking at 3Hz and 6Hz frequency (50% duty cycle).
+For 3Hz duty cylce is about 167 msec, for 6Hz is about 83 msec.
echo oneshot > trigger
-This adds the following sysfs attributes to the LED:
-
- delay_on - specifies for how many milliseconds the LED has to stay at
- LED_FULL brightness after it has been armed.
- Default to 100 ms.
-
- delay_off - specifies for how many milliseconds the LED has to stay at
- LED_OFF brightness after it has been armed.
- Default to 100 ms.
-
- invert - reverse the blink logic. If set to 0 (default) blink on for delay_on
- ms, then blink off for delay_off ms, leaving the LED normally off. If
- set to 1, blink off for delay_off ms, then blink on for delay_on ms,
- leaving the LED normally on.
- Setting this value also immediately change the LED state.
-
- shot - write any non-empty string to signal an events, this starts a blink
- sequence if not already running.
+This adds sysfs attributes to the LED that are documented in:
+Documentation/ABI/testing/sysfs-class-led-trigger-oneshot
Example use-case: network devices, initialization:
--- /dev/null
+Userspace LEDs
+==============
+
+The uleds driver supports userspace LEDs. This can be useful for testing
+triggers and can also be used to implement virtual LEDs.
+
+
+Usage
+=====
+
+When the driver is loaded, a character device is created at /dev/uleds. To
+create a new LED class device, open /dev/uleds and write a uleds_user_dev
+structure to it (found in kernel public header file linux/uleds.h).
+
+ #define ULEDS_MAX_NAME_SIZE 80
+
+ struct uleds_user_dev {
+ char name[ULEDS_MAX_NAME_SIZE];
+ };
+
+A new LED class device will be created with the name given. The name can be
+any valid file name, but consider using the LED class naming convention of
+"devicename:color:function".
+
+The current brightness is found by reading a single byte from the character
+device. Values are unsigned: 0 to 255. Reading does not block and always returns
+the most recent brightness value. The device node can also be polled to notify
+when the brightness value changes.
+
+The LED class device will be removed when the open file handle to /dev/uleds
+is closed.
+
+
+Example
+=======
+
+/*
+ * uledmon.c
+ *
+ * This program creates a new userspace LED class device and monitors it. A
+ * timestamp and brightness value is printed each time the brightness changes.
+ *
+ * Usage: uledmon <device-name>
+ *
+ * <device-name> is the name of the LED class device to be created. Pressing
+ * CTRL+C will exit.
+ */
+
+#include <fcntl.h>
+#include <poll.h>
+#include <stdio.h>
+#include <string.h>
+#include <time.h>
+#include <unistd.h>
+
+#include <linux/uleds.h>
+
+int main(int argc, char const *argv[])
+{
+ struct uleds_user_dev uleds_dev;
+ int fd, ret;
+ struct pollfd pfd;
+ unsigned char brightness;
+ struct timespec ts;
+
+ if (argc != 2) {
+ fprintf(stderr, "Requires <device-name> argument\n");
+ return 1;
+ }
+
+ strncpy(uleds_dev.name, argv[1], ULEDS_MAX_NAME_SIZE);
+
+ fd = open("/dev/uleds", O_RDWR);
+ if (fd == -1) {
+ perror("Failed to open /dev/uleds");
+ return 1;
+ }
+
+ ret = write(fd, &uleds_dev, sizeof(uleds_dev));
+ if (ret == -1) {
+ perror("Failed to write to /dev/uleds");
+ close(fd);
+ return 1;
+ }
+
+ pfd.fd = fd;
+ pfd.events = POLLIN;
+ pfd.revents = 0;
+
+ while (!(pfd.revents & (POLLERR | POLLHUP | POLLNVAL))) {
+ ret = read(fd, &brightness, 1);
+ if (ret == -1) {
+ perror("Failed to read from /dev/uleds");
+ close(fd);
+ return 1;
+ }
+ clock_gettime(CLOCK_MONOTONIC, &ts);
+ printf("[%ld.%09ld] %u\n", ts.tv_sec, ts.tv_nsec, brightness);
+ poll(&pfd, 1, -1);
+ }
+
+ close(fd);
+
+ return 0;
+}
Q: http://patchwork.ozlabs.org/project/netdev/list/
F: drivers/net/ethernet/mellanox/mlxsw/
+MELLANOX MLXCPLD LED DRIVER
+M: Vadim Pasternak <vadimp@mellanox.com>
+L: linux-leds@vger.kernel.org
+S: Supported
+W: http://www.mellanox.com
+F: drivers/leds/leds-mlxcpld.c
+F: Documentation/leds/leds-mlxcpld.txt
+
SOFT-ROCE DRIVER (rxe)
M: Moni Shoua <monis@mellanox.com>
L: linux-rdma@vger.kernel.org
This driver can also be built as a module. If so the module
will be called leds-sead3.
+config LEDS_IS31FL319X
+ tristate "LED Support for ISSI IS31FL319x I2C LED controller family"
+ depends on LEDS_CLASS && I2C && OF
+ select REGMAP_I2C
+ help
+ This option enables support for LEDs connected to ISSI IS31FL319x
+ fancy LED driver chips accessed via the I2C bus.
+ Driver supports individual PWM brightness control for each channel.
+
+ This driver can also be built as a module. If so the module will be
+ called leds-is31fl319x.
+
config LEDS_IS31FL32XX
tristate "LED support for ISSI IS31FL32XX I2C LED controller family"
depends on LEDS_CLASS && I2C && OF
This option enabled support for the LEDs on the ARM Versatile
and RealView boards. Say Y to enabled these.
+config LEDS_PM8058
+ tristate "LED Support for the Qualcomm PM8058 PMIC"
+ depends on MFD_PM8921_CORE
+ depends on LEDS_CLASS
+ help
+ Choose this option if you want to use the LED drivers in
+ the Qualcomm PM8058 PMIC.
+
+config LEDS_MLXCPLD
+ tristate "LED support for the Mellanox boards"
+ depends on X86_64 && DMI
+ depends on LEDS_CLASS
+ help
+ This option enabled support for the LEDs on the Mellanox
+ boards. Say Y to enabled these.
+
+config LEDS_USER
+ tristate "Userspace LED support"
+ depends on LEDS_CLASS
+ help
+ This option enables support for userspace LEDs. Say 'y' to enable this
+ support in kernel. To compile this driver as a module, choose 'm' here:
+ the module will be called uleds.
+
comment "LED Triggers"
source "drivers/leds/trigger/Kconfig"
obj-$(CONFIG_LEDS_KTD2692) += leds-ktd2692.o
obj-$(CONFIG_LEDS_POWERNV) += leds-powernv.o
obj-$(CONFIG_LEDS_SEAD3) += leds-sead3.o
+obj-$(CONFIG_LEDS_IS31FL319X) += leds-is31fl319x.o
obj-$(CONFIG_LEDS_IS31FL32XX) += leds-is31fl32xx.o
+obj-$(CONFIG_LEDS_PM8058) += leds-pm8058.o
+obj-$(CONFIG_LEDS_MLXCPLD) += leds-mlxcpld.o
# LED SPI Drivers
obj-$(CONFIG_LEDS_DAC124S085) += leds-dac124s085.o
+# LED Userspace Drivers
+obj-$(CONFIG_LEDS_USER) += uleds.o
+
# LED Triggers
obj-$(CONFIG_LEDS_TRIGGERS) += trigger/
*
*/
-#include <linux/module.h>
+#include <linux/export.h>
#include <linux/kernel.h>
#include <linux/list.h>
#include <linux/spinlock.h>
down_read(&led_cdev->trigger_lock);
if (!led_cdev->trigger)
- len += sprintf(buf+len, "[none] ");
+ len += scnprintf(buf+len, PAGE_SIZE - len, "[none] ");
else
- len += sprintf(buf+len, "none ");
+ len += scnprintf(buf+len, PAGE_SIZE - len, "none ");
list_for_each_entry(trig, &trigger_list, next_trig) {
if (led_cdev->trigger && !strcmp(led_cdev->trigger->name,
trig->name))
- len += sprintf(buf+len, "[%s] ", trig->name);
+ len += scnprintf(buf+len, PAGE_SIZE - len, "[%s] ",
+ trig->name);
else
- len += sprintf(buf+len, "%s ", trig->name);
+ len += scnprintf(buf+len, PAGE_SIZE - len, "%s ",
+ trig->name);
}
up_read(&led_cdev->trigger_lock);
up_read(&triggers_list_lock);
- len += sprintf(len+buf, "\n");
+ len += scnprintf(len+buf, PAGE_SIZE - len, "\n");
return len;
}
EXPORT_SYMBOL_GPL(led_trigger_show);
kfree(trig);
}
EXPORT_SYMBOL_GPL(led_trigger_unregister_simple);
-
-MODULE_AUTHOR("Richard Purdie");
-MODULE_LICENSE("GPL");
-MODULE_DESCRIPTION("LED Triggers Core");
--- /dev/null
+/*
+ * Copyright 2015-16 Golden Delicious Computers
+ *
+ * Author: Nikolaus Schaller <hns@goldelico.com>
+ *
+ * This file is subject to the terms and conditions of version 2 of
+ * the GNU General Public License. See the file COPYING in the main
+ * directory of this archive for more details.
+ *
+ * LED driver for the IS31FL319{0,1,3,6,9} to drive 1, 3, 6 or 9 light
+ * effect LEDs.
+ *
+ */
+
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/leds.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+/* register numbers */
+#define IS31FL319X_SHUTDOWN 0x00
+#define IS31FL319X_CTRL1 0x01
+#define IS31FL319X_CTRL2 0x02
+#define IS31FL319X_CONFIG1 0x03
+#define IS31FL319X_CONFIG2 0x04
+#define IS31FL319X_RAMP_MODE 0x05
+#define IS31FL319X_BREATH_MASK 0x06
+#define IS31FL319X_PWM(channel) (0x07 + channel)
+#define IS31FL319X_DATA_UPDATE 0x10
+#define IS31FL319X_T0(channel) (0x11 + channel)
+#define IS31FL319X_T123_1 0x1a
+#define IS31FL319X_T123_2 0x1b
+#define IS31FL319X_T123_3 0x1c
+#define IS31FL319X_T4(channel) (0x1d + channel)
+#define IS31FL319X_TIME_UPDATE 0x26
+#define IS31FL319X_RESET 0xff
+
+#define IS31FL319X_REG_CNT (IS31FL319X_RESET + 1)
+
+#define IS31FL319X_MAX_LEDS 9
+
+/* CS (Current Setting) in CONFIG2 register */
+#define IS31FL319X_CONFIG2_CS_SHIFT 4
+#define IS31FL319X_CONFIG2_CS_MASK 0x7
+#define IS31FL319X_CONFIG2_CS_STEP_REF 12
+
+#define IS31FL319X_CURRENT_MIN ((u32)5000)
+#define IS31FL319X_CURRENT_MAX ((u32)40000)
+#define IS31FL319X_CURRENT_STEP ((u32)5000)
+#define IS31FL319X_CURRENT_DEFAULT ((u32)20000)
+
+/* Audio gain in CONFIG2 register */
+#define IS31FL319X_AUDIO_GAIN_DB_MAX ((u32)21)
+#define IS31FL319X_AUDIO_GAIN_DB_STEP ((u32)3)
+
+/*
+ * regmap is used as a cache of chip's register space,
+ * to avoid reading back brightness values from chip,
+ * which is known to hang.
+ */
+struct is31fl319x_chip {
+ const struct is31fl319x_chipdef *cdef;
+ struct i2c_client *client;
+ struct regmap *regmap;
+ struct mutex lock;
+ u32 audio_gain_db;
+
+ struct is31fl319x_led {
+ struct is31fl319x_chip *chip;
+ struct led_classdev cdev;
+ u32 max_microamp;
+ bool configured;
+ } leds[IS31FL319X_MAX_LEDS];
+};
+
+struct is31fl319x_chipdef {
+ int num_leds;
+};
+
+static const struct is31fl319x_chipdef is31fl3190_cdef = {
+ .num_leds = 1,
+};
+
+static const struct is31fl319x_chipdef is31fl3193_cdef = {
+ .num_leds = 3,
+};
+
+static const struct is31fl319x_chipdef is31fl3196_cdef = {
+ .num_leds = 6,
+};
+
+static const struct is31fl319x_chipdef is31fl3199_cdef = {
+ .num_leds = 9,
+};
+
+static const struct of_device_id of_is31fl319x_match[] = {
+ { .compatible = "issi,is31fl3190", .data = &is31fl3190_cdef, },
+ { .compatible = "issi,is31fl3191", .data = &is31fl3190_cdef, },
+ { .compatible = "issi,is31fl3193", .data = &is31fl3193_cdef, },
+ { .compatible = "issi,is31fl3196", .data = &is31fl3196_cdef, },
+ { .compatible = "issi,is31fl3199", .data = &is31fl3199_cdef, },
+ { .compatible = "si-en,sn3199", .data = &is31fl3199_cdef, },
+ { }
+};
+MODULE_DEVICE_TABLE(of, of_is31fl319x_match);
+
+static int is31fl319x_brightness_set(struct led_classdev *cdev,
+ enum led_brightness brightness)
+{
+ struct is31fl319x_led *led = container_of(cdev, struct is31fl319x_led,
+ cdev);
+ struct is31fl319x_chip *is31 = led->chip;
+ int chan = led - is31->leds;
+ int ret;
+ int i;
+ u8 ctrl1 = 0, ctrl2 = 0;
+
+ dev_dbg(&is31->client->dev, "%s %d: %d\n", __func__, chan, brightness);
+
+ mutex_lock(&is31->lock);
+
+ /* update PWM register */
+ ret = regmap_write(is31->regmap, IS31FL319X_PWM(chan), brightness);
+ if (ret < 0)
+ goto out;
+
+ /* read current brightness of all PWM channels */
+ for (i = 0; i < is31->cdef->num_leds; i++) {
+ unsigned int pwm_value;
+ bool on;
+
+ /*
+ * since neither cdev nor the chip can provide
+ * the current setting, we read from the regmap cache
+ */
+
+ ret = regmap_read(is31->regmap, IS31FL319X_PWM(i), &pwm_value);
+ dev_dbg(&is31->client->dev, "%s read %d: ret=%d: %d\n",
+ __func__, i, ret, pwm_value);
+ on = ret >= 0 && pwm_value > LED_OFF;
+
+ if (i < 3)
+ ctrl1 |= on << i; /* 0..2 => bit 0..2 */
+ else if (i < 6)
+ ctrl1 |= on << (i + 1); /* 3..5 => bit 4..6 */
+ else
+ ctrl2 |= on << (i - 6); /* 6..8 => bit 0..2 */
+ }
+
+ if (ctrl1 > 0 || ctrl2 > 0) {
+ dev_dbg(&is31->client->dev, "power up %02x %02x\n",
+ ctrl1, ctrl2);
+ regmap_write(is31->regmap, IS31FL319X_CTRL1, ctrl1);
+ regmap_write(is31->regmap, IS31FL319X_CTRL2, ctrl2);
+ /* update PWMs */
+ regmap_write(is31->regmap, IS31FL319X_DATA_UPDATE, 0x00);
+ /* enable chip from shut down */
+ ret = regmap_write(is31->regmap, IS31FL319X_SHUTDOWN, 0x01);
+ } else {
+ dev_dbg(&is31->client->dev, "power down\n");
+ /* shut down (no need to clear CTRL1/2) */
+ ret = regmap_write(is31->regmap, IS31FL319X_SHUTDOWN, 0x00);
+ }
+
+out:
+ mutex_unlock(&is31->lock);
+
+ return ret;
+}
+
+static int is31fl319x_parse_child_dt(const struct device *dev,
+ const struct device_node *child,
+ struct is31fl319x_led *led)
+{
+ struct led_classdev *cdev = &led->cdev;
+ int ret;
+
+ if (of_property_read_string(child, "label", &cdev->name))
+ cdev->name = child->name;
+
+ ret = of_property_read_string(child, "linux,default-trigger",
+ &cdev->default_trigger);
+ if (ret < 0 && ret != -EINVAL) /* is optional */
+ return ret;
+
+ led->max_microamp = IS31FL319X_CURRENT_DEFAULT;
+ ret = of_property_read_u32(child, "led-max-microamp",
+ &led->max_microamp);
+ if (!ret) {
+ if (led->max_microamp < IS31FL319X_CURRENT_MIN)
+ return -EINVAL; /* not supported */
+ led->max_microamp = min(led->max_microamp,
+ IS31FL319X_CURRENT_MAX);
+ }
+
+ return 0;
+}
+
+static int is31fl319x_parse_dt(struct device *dev,
+ struct is31fl319x_chip *is31)
+{
+ struct device_node *np = dev->of_node, *child;
+ const struct of_device_id *of_dev_id;
+ int count;
+ int ret;
+
+ if (!np)
+ return -ENODEV;
+
+ of_dev_id = of_match_device(of_is31fl319x_match, dev);
+ if (!of_dev_id) {
+ dev_err(dev, "Failed to match device with supported chips\n");
+ return -EINVAL;
+ }
+
+ is31->cdef = of_dev_id->data;
+
+ count = of_get_child_count(np);
+
+ dev_dbg(dev, "probe %s with %d leds defined in DT\n",
+ of_dev_id->compatible, count);
+
+ if (!count || count > is31->cdef->num_leds) {
+ dev_err(dev, "Number of leds defined must be between 1 and %u\n",
+ is31->cdef->num_leds);
+ return -ENODEV;
+ }
+
+ for_each_child_of_node(np, child) {
+ struct is31fl319x_led *led;
+ u32 reg;
+
+ ret = of_property_read_u32(child, "reg", ®);
+ if (ret) {
+ dev_err(dev, "Failed to read led 'reg' property\n");
+ goto put_child_node;
+ }
+
+ if (reg < 1 || reg > is31->cdef->num_leds) {
+ dev_err(dev, "invalid led reg %u\n", reg);
+ ret = -EINVAL;
+ goto put_child_node;
+ }
+
+ led = &is31->leds[reg - 1];
+
+ if (led->configured) {
+ dev_err(dev, "led %u is already configured\n", reg);
+ ret = -EINVAL;
+ goto put_child_node;
+ }
+
+ ret = is31fl319x_parse_child_dt(dev, child, led);
+ if (ret) {
+ dev_err(dev, "led %u DT parsing failed\n", reg);
+ goto put_child_node;
+ }
+
+ led->configured = true;
+ }
+
+ is31->audio_gain_db = 0;
+ ret = of_property_read_u32(np, "audio-gain-db", &is31->audio_gain_db);
+ if (!ret)
+ is31->audio_gain_db = min(is31->audio_gain_db,
+ IS31FL319X_AUDIO_GAIN_DB_MAX);
+
+ return 0;
+
+put_child_node:
+ of_node_put(child);
+ return ret;
+}
+
+static bool is31fl319x_readable_reg(struct device *dev, unsigned int reg)
+{ /* we have no readable registers */
+ return false;
+}
+
+static bool is31fl319x_volatile_reg(struct device *dev, unsigned int reg)
+{ /* volatile registers are not cached */
+ switch (reg) {
+ case IS31FL319X_DATA_UPDATE:
+ case IS31FL319X_TIME_UPDATE:
+ case IS31FL319X_RESET:
+ return true; /* always write-through */
+ default:
+ return false;
+ }
+}
+
+static const struct reg_default is31fl319x_reg_defaults[] = {
+ { IS31FL319X_CONFIG1, 0x00},
+ { IS31FL319X_CONFIG2, 0x00},
+ { IS31FL319X_PWM(0), 0x00},
+ { IS31FL319X_PWM(1), 0x00},
+ { IS31FL319X_PWM(2), 0x00},
+ { IS31FL319X_PWM(3), 0x00},
+ { IS31FL319X_PWM(4), 0x00},
+ { IS31FL319X_PWM(5), 0x00},
+ { IS31FL319X_PWM(6), 0x00},
+ { IS31FL319X_PWM(7), 0x00},
+ { IS31FL319X_PWM(8), 0x00},
+};
+
+static struct regmap_config regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+ .max_register = IS31FL319X_REG_CNT,
+ .cache_type = REGCACHE_FLAT,
+ .readable_reg = is31fl319x_readable_reg,
+ .volatile_reg = is31fl319x_volatile_reg,
+ .reg_defaults = is31fl319x_reg_defaults,
+ .num_reg_defaults = ARRAY_SIZE(is31fl319x_reg_defaults),
+};
+
+static inline int is31fl319x_microamp_to_cs(struct device *dev, u32 microamp)
+{ /* round down to nearest supported value (range check done by caller) */
+ u32 step = microamp / IS31FL319X_CURRENT_STEP;
+
+ return ((IS31FL319X_CONFIG2_CS_STEP_REF - step) &
+ IS31FL319X_CONFIG2_CS_MASK) <<
+ IS31FL319X_CONFIG2_CS_SHIFT; /* CS encoding */
+}
+
+static inline int is31fl319x_db_to_gain(u32 dezibel)
+{ /* round down to nearest supported value (range check done by caller) */
+ return dezibel / IS31FL319X_AUDIO_GAIN_DB_STEP;
+}
+
+static int is31fl319x_probe(struct i2c_client *client,
+ const struct i2c_device_id *id)
+{
+ struct is31fl319x_chip *is31;
+ struct device *dev = &client->dev;
+ struct i2c_adapter *adapter = to_i2c_adapter(dev->parent);
+ int err;
+ int i = 0;
+ u32 aggregated_led_microamp = IS31FL319X_CURRENT_MAX;
+
+ if (!i2c_check_functionality(adapter, I2C_FUNC_I2C))
+ return -EIO;
+
+ is31 = devm_kzalloc(&client->dev, sizeof(*is31), GFP_KERNEL);
+ if (!is31)
+ return -ENOMEM;
+
+ mutex_init(&is31->lock);
+
+ err = is31fl319x_parse_dt(&client->dev, is31);
+ if (err)
+ goto free_mutex;
+
+ is31->client = client;
+ is31->regmap = devm_regmap_init_i2c(client, ®map_config);
+ if (IS_ERR(is31->regmap)) {
+ dev_err(&client->dev, "failed to allocate register map\n");
+ err = PTR_ERR(is31->regmap);
+ goto free_mutex;
+ }
+
+ i2c_set_clientdata(client, is31);
+
+ /* check for write-reply from chip (we can't read any registers) */
+ err = regmap_write(is31->regmap, IS31FL319X_RESET, 0x00);
+ if (err < 0) {
+ dev_err(&client->dev, "no response from chip write: err = %d\n",
+ err);
+ err = -EIO; /* does not answer */
+ goto free_mutex;
+ }
+
+ /*
+ * Kernel conventions require per-LED led-max-microamp property.
+ * But the chip does not allow to limit individual LEDs.
+ * So we take minimum from all subnodes for safety of hardware.
+ */
+ for (i = 0; i < is31->cdef->num_leds; i++)
+ if (is31->leds[i].configured &&
+ is31->leds[i].max_microamp < aggregated_led_microamp)
+ aggregated_led_microamp = is31->leds[i].max_microamp;
+
+ regmap_write(is31->regmap, IS31FL319X_CONFIG2,
+ is31fl319x_microamp_to_cs(dev, aggregated_led_microamp) |
+ is31fl319x_db_to_gain(is31->audio_gain_db));
+
+ for (i = 0; i < is31->cdef->num_leds; i++) {
+ struct is31fl319x_led *led = &is31->leds[i];
+
+ if (!led->configured)
+ continue;
+
+ led->chip = is31;
+ led->cdev.brightness_set_blocking = is31fl319x_brightness_set;
+
+ err = devm_led_classdev_register(&client->dev, &led->cdev);
+ if (err < 0)
+ goto free_mutex;
+ }
+
+ return 0;
+
+free_mutex:
+ mutex_destroy(&is31->lock);
+ return err;
+}
+
+static int is31fl319x_remove(struct i2c_client *client)
+{
+ struct is31fl319x_chip *is31 = i2c_get_clientdata(client);
+
+ mutex_destroy(&is31->lock);
+ return 0;
+}
+
+/*
+ * i2c-core (and modalias) requires that id_table be properly filled,
+ * even though it is not used for DeviceTree based instantiation.
+ */
+static const struct i2c_device_id is31fl319x_id[] = {
+ { "is31fl3190" },
+ { "is31fl3191" },
+ { "is31fl3193" },
+ { "is31fl3196" },
+ { "is31fl3199" },
+ { "sn3199" },
+ {},
+};
+MODULE_DEVICE_TABLE(i2c, is31fl319x_id);
+
+static struct i2c_driver is31fl319x_driver = {
+ .driver = {
+ .name = "leds-is31fl319x",
+ .of_match_table = of_match_ptr(of_is31fl319x_match),
+ },
+ .probe = is31fl319x_probe,
+ .remove = is31fl319x_remove,
+ .id_table = is31fl319x_id,
+};
+
+module_i2c_driver(is31fl319x_driver);
+
+MODULE_AUTHOR("H. Nikolaus Schaller <hns@goldelico.com>");
+MODULE_AUTHOR("Andrey Utkin <andrey_utkin@fastmail.com>");
+MODULE_DESCRIPTION("IS31FL319X LED driver");
+MODULE_LICENSE("GPL v2");
--- /dev/null
+/*
+ * drivers/leds/leds-mlxcpld.c
+ * Copyright (c) 2016 Mellanox Technologies. All rights reserved.
+ * Copyright (c) 2016 Vadim Pasternak <vadimp@mellanox.com>
+ *
+ * Redistribution and use in source and binary forms, with or without
+ * modification, are permitted provided that the following conditions are met:
+ *
+ * 1. Redistributions of source code must retain the above copyright
+ * notice, this list of conditions and the following disclaimer.
+ * 2. Redistributions in binary form must reproduce the above copyright
+ * notice, this list of conditions and the following disclaimer in the
+ * documentation and/or other materials provided with the distribution.
+ * 3. Neither the names of the copyright holders nor the names of its
+ * contributors may be used to endorse or promote products derived from
+ * this software without specific prior written permission.
+ *
+ * Alternatively, this software may be distributed under the terms of the
+ * GNU General Public License ("GPL") version 2 as published by the Free
+ * Software Foundation.
+ *
+ * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+ * AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+ * IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+ * ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT OWNER OR CONTRIBUTORS BE
+ * LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
+ * CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
+ * SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
+ * INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
+ * CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
+ * ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
+ * POSSIBILITY OF SUCH DAMAGE.
+ */
+
+#include <linux/acpi.h>
+#include <linux/device.h>
+#include <linux/dmi.h>
+#include <linux/hwmon.h>
+#include <linux/hwmon-sysfs.h>
+#include <linux/io.h>
+#include <linux/leds.h>
+#include <linux/module.h>
+#include <linux/mod_devicetable.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/version.h>
+
+#define MLXPLAT_CPLD_LPC_REG_BASE_ADRR 0x2500 /* LPC bus access */
+
+/* Color codes for LEDs */
+#define MLXCPLD_LED_OFFSET_HALF 0x01 /* Offset from solid: 3Hz blink */
+#define MLXCPLD_LED_OFFSET_FULL 0x02 /* Offset from solid: 6Hz blink */
+#define MLXCPLD_LED_IS_OFF 0x00 /* Off */
+#define MLXCPLD_LED_RED_STATIC_ON 0x05 /* Solid red */
+#define MLXCPLD_LED_RED_BLINK_HALF (MLXCPLD_LED_RED_STATIC_ON + \
+ MLXCPLD_LED_OFFSET_HALF)
+#define MLXCPLD_LED_RED_BLINK_FULL (MLXCPLD_LED_RED_STATIC_ON + \
+ MLXCPLD_LED_OFFSET_FULL)
+#define MLXCPLD_LED_GREEN_STATIC_ON 0x0D /* Solid green */
+#define MLXCPLD_LED_GREEN_BLINK_HALF (MLXCPLD_LED_GREEN_STATIC_ON + \
+ MLXCPLD_LED_OFFSET_HALF)
+#define MLXCPLD_LED_GREEN_BLINK_FULL (MLXCPLD_LED_GREEN_STATIC_ON + \
+ MLXCPLD_LED_OFFSET_FULL)
+#define MLXCPLD_LED_BLINK_3HZ 167 /* ~167 msec off/on */
+#define MLXCPLD_LED_BLINK_6HZ 83 /* ~83 msec off/on */
+
+/**
+ * mlxcpld_param - LED access parameters:
+ * @offset - offset for LED access in CPLD device
+ * @mask - mask for LED access in CPLD device
+ * @base_color - base color code for LED
+**/
+struct mlxcpld_param {
+ u8 offset;
+ u8 mask;
+ u8 base_color;
+};
+
+/**
+ * mlxcpld_led_priv - LED private data:
+ * @cled - LED class device instance
+ * @param - LED CPLD access parameters
+**/
+struct mlxcpld_led_priv {
+ struct led_classdev cdev;
+ struct mlxcpld_param param;
+};
+
+#define cdev_to_priv(c) container_of(c, struct mlxcpld_led_priv, cdev)
+
+/**
+ * mlxcpld_led_profile - system LED profile (defined per system class):
+ * @offset - offset for LED access in CPLD device
+ * @mask - mask for LED access in CPLD device
+ * @base_color - base color code
+ * @brightness - default brightness setting (on/off)
+ * @name - LED name
+**/
+struct mlxcpld_led_profile {
+ u8 offset;
+ u8 mask;
+ u8 base_color;
+ enum led_brightness brightness;
+ const char *name;
+};
+
+/**
+ * mlxcpld_led_pdata - system LED private data
+ * @pdev - platform device pointer
+ * @pled - LED class device instance
+ * @profile - system configuration profile
+ * @num_led_instances - number of LED instances
+ * @lock - device access lock
+**/
+struct mlxcpld_led_pdata {
+ struct platform_device *pdev;
+ struct mlxcpld_led_priv *pled;
+ struct mlxcpld_led_profile *profile;
+ int num_led_instances;
+ spinlock_t lock;
+};
+
+static struct mlxcpld_led_pdata *mlxcpld_led;
+
+/* Default profile fit the next Mellanox systems:
+ * "msx6710", "msx6720", "msb7700", "msn2700", "msx1410",
+ * "msn2410", "msb7800", "msn2740"
+ */
+static struct mlxcpld_led_profile mlxcpld_led_default_profile[] = {
+ {
+ 0x21, 0xf0, MLXCPLD_LED_GREEN_STATIC_ON, 1,
+ "mlxcpld:fan1:green",
+ },
+ {
+ 0x21, 0xf0, MLXCPLD_LED_RED_STATIC_ON, LED_OFF,
+ "mlxcpld:fan1:red",
+ },
+ {
+ 0x21, 0x0f, MLXCPLD_LED_GREEN_STATIC_ON, 1,
+ "mlxcpld:fan2:green",
+ },
+ {
+ 0x21, 0x0f, MLXCPLD_LED_RED_STATIC_ON, LED_OFF,
+ "mlxcpld:fan2:red",
+ },
+ {
+ 0x22, 0xf0, MLXCPLD_LED_GREEN_STATIC_ON, 1,
+ "mlxcpld:fan3:green",
+ },
+ {
+ 0x22, 0xf0, MLXCPLD_LED_RED_STATIC_ON, LED_OFF,
+ "mlxcpld:fan3:red",
+ },
+ {
+ 0x22, 0x0f, MLXCPLD_LED_GREEN_STATIC_ON, 1,
+ "mlxcpld:fan4:green",
+ },
+ {
+ 0x22, 0x0f, MLXCPLD_LED_RED_STATIC_ON, LED_OFF,
+ "mlxcpld:fan4:red",
+ },
+ {
+ 0x20, 0x0f, MLXCPLD_LED_GREEN_STATIC_ON, 1,
+ "mlxcpld:psu:green",
+ },
+ {
+ 0x20, 0x0f, MLXCPLD_LED_RED_STATIC_ON, LED_OFF,
+ "mlxcpld:psu:red",
+ },
+ {
+ 0x20, 0xf0, MLXCPLD_LED_GREEN_STATIC_ON, 1,
+ "mlxcpld:status:green",
+ },
+ {
+ 0x20, 0xf0, MLXCPLD_LED_RED_STATIC_ON, LED_OFF,
+ "mlxcpld:status:red",
+ },
+};
+
+/* Profile fit the Mellanox systems based on "msn2100" */
+static struct mlxcpld_led_profile mlxcpld_led_msn2100_profile[] = {
+ {
+ 0x21, 0xf0, MLXCPLD_LED_GREEN_STATIC_ON, 1,
+ "mlxcpld:fan:green",
+ },
+ {
+ 0x21, 0xf0, MLXCPLD_LED_RED_STATIC_ON, LED_OFF,
+ "mlxcpld:fan:red",
+ },
+ {
+ 0x23, 0xf0, MLXCPLD_LED_GREEN_STATIC_ON, 1,
+ "mlxcpld:psu1:green",
+ },
+ {
+ 0x23, 0xf0, MLXCPLD_LED_RED_STATIC_ON, LED_OFF,
+ "mlxcpld:psu1:red",
+ },
+ {
+ 0x23, 0x0f, MLXCPLD_LED_GREEN_STATIC_ON, 1,
+ "mlxcpld:psu2:green",
+ },
+ {
+ 0x23, 0x0f, MLXCPLD_LED_RED_STATIC_ON, LED_OFF,
+ "mlxcpld:psu2:red",
+ },
+ {
+ 0x20, 0xf0, MLXCPLD_LED_GREEN_STATIC_ON, 1,
+ "mlxcpld:status:green",
+ },
+ {
+ 0x20, 0xf0, MLXCPLD_LED_RED_STATIC_ON, LED_OFF,
+ "mlxcpld:status:red",
+ },
+ {
+ 0x24, 0xf0, MLXCPLD_LED_GREEN_STATIC_ON, LED_OFF,
+ "mlxcpld:uid:blue",
+ },
+};
+
+enum mlxcpld_led_platform_types {
+ MLXCPLD_LED_PLATFORM_DEFAULT,
+ MLXCPLD_LED_PLATFORM_MSN2100,
+};
+
+static const char *mlx_product_names[] = {
+ "DEFAULT",
+ "MSN2100",
+};
+
+static enum
+mlxcpld_led_platform_types mlxcpld_led_platform_check_sys_type(void)
+{
+ const char *mlx_product_name;
+ int i;
+
+ mlx_product_name = dmi_get_system_info(DMI_PRODUCT_NAME);
+ if (!mlx_product_name)
+ return MLXCPLD_LED_PLATFORM_DEFAULT;
+
+ for (i = 1; i < ARRAY_SIZE(mlx_product_names); i++) {
+ if (strstr(mlx_product_name, mlx_product_names[i]))
+ return i;
+ }
+
+ return MLXCPLD_LED_PLATFORM_DEFAULT;
+}
+
+static void mlxcpld_led_bus_access_func(u16 base, u8 offset, u8 rw_flag,
+ u8 *data)
+{
+ u32 addr = base + offset;
+
+ if (rw_flag == 0)
+ outb(*data, addr);
+ else
+ *data = inb(addr);
+}
+
+static void mlxcpld_led_store_hw(u8 mask, u8 off, u8 vset)
+{
+ u8 nib, val;
+
+ /*
+ * Each LED is controlled through low or high nibble of the relevant
+ * CPLD register. Register offset is specified by off parameter.
+ * Parameter vset provides color code: 0x0 for off, 0x5 for solid red,
+ * 0x6 for 3Hz blink red, 0xd for solid green, 0xe for 3Hz blink
+ * green.
+ * Parameter mask specifies which nibble is used for specific LED: mask
+ * 0xf0 - lower nibble is to be used (bits from 0 to 3), mask 0x0f -
+ * higher nibble (bits from 4 to 7).
+ */
+ spin_lock(&mlxcpld_led->lock);
+ mlxcpld_led_bus_access_func(MLXPLAT_CPLD_LPC_REG_BASE_ADRR, off, 1,
+ &val);
+ nib = (mask == 0xf0) ? vset : (vset << 4);
+ val = (val & mask) | nib;
+ mlxcpld_led_bus_access_func(MLXPLAT_CPLD_LPC_REG_BASE_ADRR, off, 0,
+ &val);
+ spin_unlock(&mlxcpld_led->lock);
+}
+
+static void mlxcpld_led_brightness_set(struct led_classdev *led,
+ enum led_brightness value)
+{
+ struct mlxcpld_led_priv *pled = cdev_to_priv(led);
+
+ if (value) {
+ mlxcpld_led_store_hw(pled->param.mask, pled->param.offset,
+ pled->param.base_color);
+ return;
+ }
+
+ mlxcpld_led_store_hw(pled->param.mask, pled->param.offset,
+ MLXCPLD_LED_IS_OFF);
+}
+
+static int mlxcpld_led_blink_set(struct led_classdev *led,
+ unsigned long *delay_on,
+ unsigned long *delay_off)
+{
+ struct mlxcpld_led_priv *pled = cdev_to_priv(led);
+
+ /*
+ * HW supports two types of blinking: full (6Hz) and half (3Hz).
+ * For delay on/off zero default setting 3Hz is used.
+ */
+ if (!(*delay_on == 0 && *delay_off == 0) &&
+ !(*delay_on == MLXCPLD_LED_BLINK_3HZ &&
+ *delay_off == MLXCPLD_LED_BLINK_3HZ) &&
+ !(*delay_on == MLXCPLD_LED_BLINK_6HZ &&
+ *delay_off == MLXCPLD_LED_BLINK_6HZ))
+ return -EINVAL;
+
+ if (*delay_on == MLXCPLD_LED_BLINK_6HZ)
+ mlxcpld_led_store_hw(pled->param.mask, pled->param.offset,
+ pled->param.base_color +
+ MLXCPLD_LED_OFFSET_FULL);
+ else
+ mlxcpld_led_store_hw(pled->param.mask, pled->param.offset,
+ pled->param.base_color +
+ MLXCPLD_LED_OFFSET_HALF);
+
+ return 0;
+}
+
+static int mlxcpld_led_config(struct device *dev,
+ struct mlxcpld_led_pdata *cpld)
+{
+ int i;
+ int err;
+
+ cpld->pled = devm_kzalloc(dev, sizeof(struct mlxcpld_led_priv) *
+ cpld->num_led_instances, GFP_KERNEL);
+ if (!cpld->pled)
+ return -ENOMEM;
+
+ for (i = 0; i < cpld->num_led_instances; i++) {
+ cpld->pled[i].cdev.name = cpld->profile[i].name;
+ cpld->pled[i].cdev.brightness = cpld->profile[i].brightness;
+ cpld->pled[i].cdev.max_brightness = 1;
+ cpld->pled[i].cdev.brightness_set = mlxcpld_led_brightness_set;
+ cpld->pled[i].cdev.blink_set = mlxcpld_led_blink_set;
+ cpld->pled[i].cdev.flags = LED_CORE_SUSPENDRESUME;
+ err = devm_led_classdev_register(dev, &cpld->pled[i].cdev);
+ if (err)
+ return err;
+
+ cpld->pled[i].param.offset = mlxcpld_led->profile[i].offset;
+ cpld->pled[i].param.mask = mlxcpld_led->profile[i].mask;
+ cpld->pled[i].param.base_color =
+ mlxcpld_led->profile[i].base_color;
+
+ if (mlxcpld_led->profile[i].brightness)
+ mlxcpld_led_brightness_set(&cpld->pled[i].cdev,
+ mlxcpld_led->profile[i].brightness);
+ }
+
+ return 0;
+}
+
+static int __init mlxcpld_led_probe(struct platform_device *pdev)
+{
+ enum mlxcpld_led_platform_types mlxcpld_led_plat =
+ mlxcpld_led_platform_check_sys_type();
+
+ mlxcpld_led = devm_kzalloc(&pdev->dev, sizeof(*mlxcpld_led),
+ GFP_KERNEL);
+ if (!mlxcpld_led)
+ return -ENOMEM;
+
+ mlxcpld_led->pdev = pdev;
+
+ switch (mlxcpld_led_plat) {
+ case MLXCPLD_LED_PLATFORM_MSN2100:
+ mlxcpld_led->profile = mlxcpld_led_msn2100_profile;
+ mlxcpld_led->num_led_instances =
+ ARRAY_SIZE(mlxcpld_led_msn2100_profile);
+ break;
+
+ default:
+ mlxcpld_led->profile = mlxcpld_led_default_profile;
+ mlxcpld_led->num_led_instances =
+ ARRAY_SIZE(mlxcpld_led_default_profile);
+ break;
+ }
+
+ spin_lock_init(&mlxcpld_led->lock);
+
+ return mlxcpld_led_config(&pdev->dev, mlxcpld_led);
+}
+
+static struct platform_driver mlxcpld_led_driver = {
+ .driver = {
+ .name = KBUILD_MODNAME,
+ },
+};
+
+static int __init mlxcpld_led_init(void)
+{
+ struct platform_device *pdev;
+ int err;
+
+ pdev = platform_device_register_simple(KBUILD_MODNAME, -1, NULL, 0);
+ if (!pdev) {
+ pr_err("Device allocation failed\n");
+ return -ENOMEM;
+ }
+
+ err = platform_driver_probe(&mlxcpld_led_driver, mlxcpld_led_probe);
+ if (err) {
+ pr_err("Probe platform driver failed\n");
+ platform_device_unregister(pdev);
+ }
+
+ return err;
+}
+
+static void __exit mlxcpld_led_exit(void)
+{
+ platform_device_unregister(mlxcpld_led->pdev);
+ platform_driver_unregister(&mlxcpld_led_driver);
+}
+
+module_init(mlxcpld_led_init);
+module_exit(mlxcpld_led_exit);
+
+MODULE_AUTHOR("Vadim Pasternak <vadimp@mellanox.com>");
+MODULE_DESCRIPTION("Mellanox board LED driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:leds_mlxcpld");
--- /dev/null
+/* Copyright (c) 2010, 2011, 2016 The Linux Foundation. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 and
+ * only version 2 as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+#include <linux/leds.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pm.h>
+#include <linux/regmap.h>
+
+#define PM8058_LED_TYPE_COMMON 0x00
+#define PM8058_LED_TYPE_KEYPAD 0x01
+#define PM8058_LED_TYPE_FLASH 0x02
+
+#define PM8058_LED_TYPE_COMMON_MASK 0xf8
+#define PM8058_LED_TYPE_KEYPAD_MASK 0xf0
+#define PM8058_LED_TYPE_COMMON_SHIFT 3
+#define PM8058_LED_TYPE_KEYPAD_SHIFT 4
+
+struct pm8058_led {
+ struct regmap *map;
+ u32 reg;
+ u32 ledtype;
+ struct led_classdev cdev;
+};
+
+static void pm8058_led_set(struct led_classdev *cled,
+ enum led_brightness value)
+{
+ struct pm8058_led *led;
+ int ret = 0;
+ unsigned int mask = 0;
+ unsigned int val = 0;
+
+ led = container_of(cled, struct pm8058_led, cdev);
+ switch (led->ledtype) {
+ case PM8058_LED_TYPE_COMMON:
+ mask = PM8058_LED_TYPE_COMMON_MASK;
+ val = value << PM8058_LED_TYPE_COMMON_SHIFT;
+ break;
+ case PM8058_LED_TYPE_KEYPAD:
+ case PM8058_LED_TYPE_FLASH:
+ mask = PM8058_LED_TYPE_KEYPAD_MASK;
+ val = value << PM8058_LED_TYPE_KEYPAD_SHIFT;
+ break;
+ default:
+ break;
+ }
+
+ ret = regmap_update_bits(led->map, led->reg, mask, val);
+ if (ret)
+ pr_err("Failed to set LED brightness\n");
+}
+
+static enum led_brightness pm8058_led_get(struct led_classdev *cled)
+{
+ struct pm8058_led *led;
+ int ret;
+ unsigned int val;
+
+ led = container_of(cled, struct pm8058_led, cdev);
+
+ ret = regmap_read(led->map, led->reg, &val);
+ if (ret) {
+ pr_err("Failed to get LED brightness\n");
+ return LED_OFF;
+ }
+
+ switch (led->ledtype) {
+ case PM8058_LED_TYPE_COMMON:
+ val &= PM8058_LED_TYPE_COMMON_MASK;
+ val >>= PM8058_LED_TYPE_COMMON_SHIFT;
+ break;
+ case PM8058_LED_TYPE_KEYPAD:
+ case PM8058_LED_TYPE_FLASH:
+ val &= PM8058_LED_TYPE_KEYPAD_MASK;
+ val >>= PM8058_LED_TYPE_KEYPAD_SHIFT;
+ break;
+ default:
+ val = LED_OFF;
+ break;
+ }
+
+ return val;
+}
+
+static int pm8058_led_probe(struct platform_device *pdev)
+{
+ struct pm8058_led *led;
+ struct device_node *np = pdev->dev.of_node;
+ int ret;
+ struct regmap *map;
+ const char *state;
+ enum led_brightness maxbright;
+
+ led = devm_kzalloc(&pdev->dev, sizeof(*led), GFP_KERNEL);
+ if (!led)
+ return -ENOMEM;
+
+ led->ledtype = (u32)of_device_get_match_data(&pdev->dev);
+
+ map = dev_get_regmap(pdev->dev.parent, NULL);
+ if (!map) {
+ dev_err(&pdev->dev, "Parent regmap unavailable.\n");
+ return -ENXIO;
+ }
+ led->map = map;
+
+ ret = of_property_read_u32(np, "reg", &led->reg);
+ if (ret) {
+ dev_err(&pdev->dev, "no register offset specified\n");
+ return -EINVAL;
+ }
+
+ /* Use label else node name */
+ led->cdev.name = of_get_property(np, "label", NULL) ? : np->name;
+ led->cdev.default_trigger =
+ of_get_property(np, "linux,default-trigger", NULL);
+ led->cdev.brightness_set = pm8058_led_set;
+ led->cdev.brightness_get = pm8058_led_get;
+ if (led->ledtype == PM8058_LED_TYPE_COMMON)
+ maxbright = 31; /* 5 bits */
+ else
+ maxbright = 15; /* 4 bits */
+ led->cdev.max_brightness = maxbright;
+
+ state = of_get_property(np, "default-state", NULL);
+ if (state) {
+ if (!strcmp(state, "keep")) {
+ led->cdev.brightness = pm8058_led_get(&led->cdev);
+ } else if (!strcmp(state, "on")) {
+ led->cdev.brightness = maxbright;
+ pm8058_led_set(&led->cdev, maxbright);
+ } else {
+ led->cdev.brightness = LED_OFF;
+ pm8058_led_set(&led->cdev, LED_OFF);
+ }
+ }
+
+ if (led->ledtype == PM8058_LED_TYPE_KEYPAD ||
+ led->ledtype == PM8058_LED_TYPE_FLASH)
+ led->cdev.flags = LED_CORE_SUSPENDRESUME;
+
+ ret = devm_led_classdev_register(&pdev->dev, &led->cdev);
+ if (ret) {
+ dev_err(&pdev->dev, "unable to register led \"%s\"\n",
+ led->cdev.name);
+ return ret;
+ }
+
+ return 0;
+}
+
+static const struct of_device_id pm8058_leds_id_table[] = {
+ {
+ .compatible = "qcom,pm8058-led",
+ .data = (void *)PM8058_LED_TYPE_COMMON
+ },
+ {
+ .compatible = "qcom,pm8058-keypad-led",
+ .data = (void *)PM8058_LED_TYPE_KEYPAD
+ },
+ {
+ .compatible = "qcom,pm8058-flash-led",
+ .data = (void *)PM8058_LED_TYPE_FLASH
+ },
+ { },
+};
+MODULE_DEVICE_TABLE(of, pm8058_leds_id_table);
+
+static struct platform_driver pm8058_led_driver = {
+ .probe = pm8058_led_probe,
+ .driver = {
+ .name = "pm8058-leds",
+ .of_match_table = pm8058_leds_id_table,
+ },
+};
+module_platform_driver(pm8058_led_driver);
+
+MODULE_DESCRIPTION("PM8058 LEDs driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:pm8058-leds");
--- /dev/null
+/*
+ * Userspace driver for the LED subsystem
+ *
+ * Copyright (C) 2016 David Lechner <david@lechnology.com>
+ *
+ * Based on uinput.c: Aristeu Sergio Rozanski Filho <aris@cathedrallabs.org>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+#include <linux/fs.h>
+#include <linux/init.h>
+#include <linux/leds.h>
+#include <linux/miscdevice.h>
+#include <linux/module.h>
+#include <linux/poll.h>
+#include <linux/sched.h>
+#include <linux/slab.h>
+
+#include <uapi/linux/uleds.h>
+
+#define ULEDS_NAME "uleds"
+
+enum uleds_state {
+ ULEDS_STATE_UNKNOWN,
+ ULEDS_STATE_REGISTERED,
+};
+
+struct uleds_device {
+ struct uleds_user_dev user_dev;
+ struct led_classdev led_cdev;
+ struct mutex mutex;
+ enum uleds_state state;
+ wait_queue_head_t waitq;
+ unsigned char brightness;
+ unsigned char new_data;
+};
+
+static void uleds_brightness_set(struct led_classdev *led_cdev,
+ enum led_brightness brightness)
+{
+ struct uleds_device *udev = container_of(led_cdev, struct uleds_device,
+ led_cdev);
+
+ if (udev->brightness != brightness) {
+ udev->brightness = brightness;
+ udev->new_data = 1;
+ wake_up_interruptible(&udev->waitq);
+ }
+}
+
+static int uleds_open(struct inode *inode, struct file *file)
+{
+ struct uleds_device *udev;
+
+ udev = kzalloc(sizeof(*udev), GFP_KERNEL);
+ if (!udev)
+ return -ENOMEM;
+
+ udev->led_cdev.name = udev->user_dev.name;
+ udev->led_cdev.max_brightness = LED_FULL;
+ udev->led_cdev.brightness_set = uleds_brightness_set;
+
+ mutex_init(&udev->mutex);
+ init_waitqueue_head(&udev->waitq);
+ udev->state = ULEDS_STATE_UNKNOWN;
+
+ file->private_data = udev;
+ nonseekable_open(inode, file);
+
+ return 0;
+}
+
+static ssize_t uleds_write(struct file *file, const char __user *buffer,
+ size_t count, loff_t *ppos)
+{
+ struct uleds_device *udev = file->private_data;
+ int ret;
+
+ if (count == 0)
+ return 0;
+
+ ret = mutex_lock_interruptible(&udev->mutex);
+ if (ret)
+ return ret;
+
+ if (udev->state == ULEDS_STATE_REGISTERED) {
+ ret = -EBUSY;
+ goto out;
+ }
+
+ if (count != sizeof(struct uleds_user_dev)) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ if (copy_from_user(&udev->user_dev, buffer,
+ sizeof(struct uleds_user_dev))) {
+ ret = -EFAULT;
+ goto out;
+ }
+
+ if (!udev->user_dev.name[0]) {
+ ret = -EINVAL;
+ goto out;
+ }
+
+ ret = led_classdev_register(NULL, &udev->led_cdev);
+ if (ret < 0)
+ goto out;
+
+ udev->state = ULEDS_STATE_REGISTERED;
+ ret = count;
+
+out:
+ mutex_unlock(&udev->mutex);
+
+ return ret;
+}
+
+static ssize_t uleds_read(struct file *file, char __user *buffer, size_t count,
+ loff_t *ppos)
+{
+ struct uleds_device *udev = file->private_data;
+ ssize_t retval;
+
+ if (count == 0)
+ return 0;
+
+ if (count != 1)
+ return -EINVAL;
+
+ do {
+ retval = mutex_lock_interruptible(&udev->mutex);
+ if (retval)
+ return retval;
+
+ if (udev->state != ULEDS_STATE_REGISTERED) {
+ retval = -ENODEV;
+ } else if (!udev->new_data && (file->f_flags & O_NONBLOCK)) {
+ retval = -EAGAIN;
+ } else {
+ retval = copy_to_user(buffer, &udev->brightness, 1);
+ udev->new_data = 0;
+ retval = 1;
+ }
+
+ mutex_unlock(&udev->mutex);
+
+ if (retval || count == 0)
+ break;
+
+ if (!(file->f_flags & O_NONBLOCK))
+ retval = wait_event_interruptible(udev->waitq,
+ udev->new_data ||
+ udev->state != ULEDS_STATE_REGISTERED);
+ } while (retval == 0);
+
+ return retval;
+}
+
+static unsigned int uleds_poll(struct file *file, poll_table *wait)
+{
+ struct uleds_device *udev = file->private_data;
+
+ poll_wait(file, &udev->waitq, wait);
+
+ if (udev->new_data)
+ return POLLIN | POLLRDNORM;
+
+ return 0;
+}
+
+static int uleds_release(struct inode *inode, struct file *file)
+{
+ struct uleds_device *udev = file->private_data;
+
+ if (udev->state == ULEDS_STATE_REGISTERED) {
+ udev->state = ULEDS_STATE_UNKNOWN;
+ led_classdev_unregister(&udev->led_cdev);
+ }
+ kfree(udev);
+
+ return 0;
+}
+
+static const struct file_operations uleds_fops = {
+ .owner = THIS_MODULE,
+ .open = uleds_open,
+ .release = uleds_release,
+ .read = uleds_read,
+ .write = uleds_write,
+ .poll = uleds_poll,
+ .llseek = no_llseek,
+};
+
+static struct miscdevice uleds_misc = {
+ .fops = &uleds_fops,
+ .minor = MISC_DYNAMIC_MINOR,
+ .name = ULEDS_NAME,
+};
+
+static int __init uleds_init(void)
+{
+ return misc_register(&uleds_misc);
+}
+module_init(uleds_init);
+
+static void __exit uleds_exit(void)
+{
+ misc_deregister(&uleds_misc);
+}
+module_exit(uleds_exit);
+
+MODULE_AUTHOR("David Lechner <david@lechnology.com>");
+MODULE_DESCRIPTION("Userspace driver for the LED subsystem");
+MODULE_LICENSE("GPL");
header-y += uhid.h
header-y += uinput.h
header-y += uio.h
+header-y += uleds.h
header-y += ultrasound.h
header-y += un.h
header-y += unistd.h
--- /dev/null
+/*
+ * Userspace driver support for the LED subsystem
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+#ifndef _UAPI__ULEDS_H_
+#define _UAPI__ULEDS_H_
+
+#define ULEDS_MAX_NAME_SIZE 80
+
+struct uleds_user_dev {
+ char name[ULEDS_MAX_NAME_SIZE];
+};
+
+#endif /* _UAPI__ULEDS_H_ */
projects / deliverable / linux.git / commitdiff
